INSTALLATION, OPERATION AND MAINTENANCE MANUAL Warning Please read carefully before proceeding with installation. Your failure to follow any attached instructions or operating parameters may lead to the product’s failure and possible damage to property. Save manual for future reference Model: RO-PURE System Tested and certified by WQA against NSF/ANSI Standard 58 for the reduction of the claims specifi ed on the performance data sheet.
Service Record Model Number:__________ Serial Number:___________ Date of Purchase:__________ Date of Install:___________ Installed by:_____________ Date Sediment Filter (6 months) Carbon Pre-Filter (6 months) Membrane (2-5 years) NOTES: Page 2 Carbon Post-Filter (6 months)
WARRANTY REGISTRATION Thank you for selecting Watts Premier for your water filtration needs. 4 Ways to Register 1. On-line at www.wattspremier.com Register your product on-line and receive a 5% discount on your next on-line order, Plus receive reduced shipping. 2. Call in your information 1-800-752-5582 Call and we will enter your information. 3. Fax in your information 623-931-0191 Fax this form directly to us. 4. Mail in the information. Please complete the form below. Mail to: Watts Premier 1725 W.
Thank you for your purchase of a state of the art Watts Premier Reverse Osmosis (RO) water treatment system. Water quality concerns are becoming more of a focus for the public. You may have heard about contaminants in the drinking water, such as Arsenic, Perchlorate, Chromium, Cryptosporidium or Giardia. There may also be some local water issues such as high levels of Lead and Copper.
Thank you for your purchase of a Watts Premier Reverse Osmosis system. With proper installation and maintenance, this system will provide you with high quality water for years to come. All of Premier’s water enhancement products are rigorously tested by independent laboratories for safety and reliability. If you have any questions or concerns, please contact our customer service department at 1-800-752-5582 (outside USA 623-931-1977) or refer to our on-line troubleshooting at www.wattspremier.com.
Operational Parameters Installation needs to comply with state and local plumbing regulations. This system is intended to be installed on the cold water line only. Operating Temperatures: Maximum 100°F (37.8°C) Minimum Operating Pressure: Maximum 85 psi (7.43 g/cm2) Minimum pH Maximum 11 Minimum 2 Parameters: Iron: Maximum 0.2 ppm TDS (Total Dissolved Solids): < 1800 ppm Turbidity: < 5NTU 40°F 4.4°C) 40 psi (2.
Note: Most sinks are predrilled with 1 ½” or 1 ¼” diameter hole that you can use for your RO faucet (If you are already using it for a sprayer or soap dispenser, you will need an additional hole for the faucet). Drill a Hole for the Faucet in a Porcelain Sink Porcelain sinks are extremely hard and can crack or chip easily. Use extreme caution when drilling. Premier accepts no responsibility for damage resulting from the installation of faucet.
WATTS Premier Chrome Monitored & Non-Monitored (Top Mount) Faucet Installation Mounting Hole Size Torque on Toggle Bolt Minimum Maximum 1.00” 1.25” 5lb.in. (max) Gather and identify the faucet pieces. Step 6 Remove faucet base & faucet spout from their respective plastic bags. From above the sink, feed the faucet base, tubing & toggle bolt down through the 1¼” mounting hole in the sink. Align the faucet base so that the handle is on the right side and the base is sitting flush on the sink top.
Green Tube Connection (From RO Module to The Adapta Valve) Step 11 Remove a brass nut, plastic sleeve and brass insert from the parts bag. Place nut on the green tube (coming from the RO Module) first, then the plastic sleeve (small taper end of plastic sleeve must point to the end of tube) and then insert the brass insert into the end of the tube. Step 12 Insert the green tube into the ¼” opening on the Adapta Valve (supplied in the parts bag) until it stops.
Drain Saddle Installation - Part# 164016 Drain Saddle fits standard 1 ¼” – 1 ½” drain pipes Caution: If you have a garbage disposal, do not install the drain line near it. Installation of the drain line must be either above the disposal, or if a second sink drain is available, install it above the cross bar on the second sink. Installation of the drain line near a garbage disposal may cause the drain line to plug.
How To Use the Quick Connect Fittings For Tubing Connections To make a connection, the tube is simply pushed into the fi tting. Place a piece of tape 1/2” from end of tube to indicate how far the tube should be inserted. The unique patented locking system holds the tube firmly in place without deforming it or restricting flow. NOTE: These diagrams are just to show how the quick connect fittings work, your product may not have this exact connector part.
Blue Tube Connection (From The RO Module To TANK) Step 22 Position tank in desired location. Stand it upright or lay it on its side (using the black plastic stand). Measure the blue tube (marked “TANK”) from the RO module over to the tank and cut it to length leaving a straight edge on the end of the tube. Then insert the tube into the quick connect fitting on the tank ball valve. Make sure the tube is pushed in all the way to the tube stop (see page 11 for quick connect fi tting use directions).
Red Tube Connection (From FAUCET To The FLOW RESTRICTOR) Step 27 Determine where the 1/4” red tubing from the faucet and the open end of the flow restrictor (attached to the end of the 1/4” black tubing from the RO Module) would join together comfortably. Cut the tubes to length, making sure the cut ends are straight. Unscrew the supplied compression nut from the open end of the flow restrictor and push the nut onto the end of the red tube.
This reverse osmosis system contains a replaceable component (the RO membrane) which is critical to the ef ficiency of the system. Replacement of this reverse osmosis membrane should be with one of identical specifications as defi ned by Watts Premier to assure the same efficiency and contaminant reduction performance. 6 Month System Maintenance Watts Premier sells a fi lter change kit which includes all replacement filters needed. Call 1-800-752-5582 or buy on-line at www.wattspremier.com.
Check Air Pressure in the Tank Note: Check air pressure only when tank is empty of water! Check air pressure in the tank when you notice a decrease in available water from the RO system. Step 1 It is recommended that you drain the tank of water, and then pump up the RO tank in order to ensure all water is out of the tank. Air can be added with a bicycle pump using the schrader valve that is located on the bottom side of the tank.
TROUBLE SHOOTING Problem Cause 1. Low/Slow Production Low Water Pressure Solution Assure a minimum of 40 psi incoming water pressure. Premier sells a booster pump if home water pressure is low. Maker sure water supply is turned on and Adapta Valve is all the way open Check tubing and straighten or replace as necessary. Replace pre-filters. Replace membrane and flow restrictor. Crimps in tubing Clogged pre-fi lters Fouled membrane 2.
Watts Premier Inc. 1725 W. Williams Drive C-20 Phoenix, AZ 85027 USA California Certification # 07-1882 RO-Pure System conforms to NSF Standard 58 for specific claims. GENERAL USE CONDITIONS: 1. System to be used with municipal or well water sources treated and tested on regular basis to insure bacteriological safe quality. DO NOT use with water that is microbiologically unsafe or unknown quality without adequate disinfection before and after the system.
Arsenic Fact Sheet Arsenic (As) is a naturally occurring contaminant found in many ground waters. Arsenic in water has no color, taste or odor. It must be measured by an arsenic test kit or lab test. Public water utilities must have their water tested for arsenic. You can obtain the results from your water utility contained with in your consumer con fidence report. If you have your own well, you will need to have the water evaluated.
Other Products from Watts Premier Watts Premier has other fine water filtration products and accessories to enhance your water and to compliment your existing RO System. Listed on the next several pages are only a few of the items we offer. Visit our website at www.wattspremier.com or call our Customer Service Representatives at 1-800-752-5582 (inside USA) 1-623-931-1977 (outside USA) for more products. Watts Premier sells a fi lter change kit which includes all replacement filters needed.
Watts Premier Ice Maker Kit - High efficiency replaceable filter that can last up to 5 years or 20,000 gallons. Prefect for residential and commercial ice makers as well as refrigerators, drinking fountains, coffee & tea brewers, motor homes and campers. Reduces chlorine taste and odor. Part No. 500327 *$36.95 each Whole House Filter Great for sediment problems such as in well water supply or areas where dirt and rust particles are a problem. Includes three 50 Micron sediment filters, and wrench.
Removing chlorine from your shower Special Chlorgon & KDF media – More effective then carbon medias with hot water applications in the removal of the following. √ Free Chlorine (CL-) √ Combined Chlorine (Sodium Hypochlorite) √ Hydrogen Sulfide (Rotten egg smell) √ Plus, its pH balanced.
Limited Warranty What your Warranty Covers: If any part of your WATTS PREMIER Reverse Osmosis System is defective in workmanship (excluding replaceable filters and membranes), return unit after obtaining a return authorization (see below), less tank, within 3 years of original retail purchase, WATTS PREMIER will repair or, at WATTS PREMIER’S option, replace the system at no charge. How to obtain Warranty Service: For warranty service, call 1-800-752-5582 for documentation and a return authorization number.
