User guide

Page 40 WS1TC & WS1.25 TC Manual
Rell Flow Control Assembly or Rell Port Plug
To clean or replace the rell ow control, pull out the elbow-locking clip and then pull straight up on the elbow. Replace the elbow
locking clip in the slot so that it is not misplaced. Twist to remove the white ow control retainer. The ow control can be removed
by prying upward through the side slots of the retainer with a small at blade screwdriver.
Chemically clean the ow control or the white ow control retainer using dilute sodium bisulte or vinegar. Do not use a wire brush.
If necessary, replace the ow control, o-ring on the ow control retainer, or the o-ring on the elbow.
Reseat the ow control so the rounded end is visible in the ow control. Reseat the white ow control retainer by pushing the
retainer into the elbow until the o-ring seats. Remove locking clip, push down on elbow to reseat and insert locking clip.
Do not use Vaseline, oils, or other unacceptable lubricants on o-rings. A silicone lubricant may be used on the o-ring on the elbow or
the white retainer.
Meter Plug
This control valve does not come equipped with a meter, instead a plug is installed. The plug should not need to be serviced.
To remove the meter plug assembly, unscrew the meter cap on the left side of the control valve. Pliers may be used to unscrew the
nut if necessary.
With the nut removed, a slot at the top of the meter plug is visible. Twist a at blade screwdriver in the slot between the control
valve body and the meter plug. When the meter plug is part way out it is easy to remove the meter plug from the housing.
Do not use a wire brush to clean the meter plug. Wipe with a clean cloth or chemically clean in dilute sodium bisulte or vinegar.
Do not use Vaseline, oils, or other unacceptable lubricants on the o-ring. A silicone lubricant may be used on the black o-ring.
Reinsert the meter plug into the side slot. Hand tighten the nut. Do not use a pipe wrench to tighten nut.
Compliance Table
Application Injector and/or Plug(s) Main Piston
Regenerant
Piston
Stack Body
WS1TC Downow
Softener or Regenerating
Filter
Injector in “DN” hole, Plug
in “UP” hole
V3011 V3174 V3005
V3001 or
V3001-02 (Mixing)
WS1TC Backwash Only
Filter
Plug in “DN” and “UP”
holes, Install Rell Port Plug
V3011 None V3005
V3001 or
V3001-02 (Mixing)
WS1.25TC Downow
Softener or Regenerating
Filter (1.32" Distributor)
Injector in “DN” hole, Plug
in “UP” hole
V3407 V3174 V3430
V3020 or
V3020-01 (Mixing)
WS1.25TC Backwash
Only Filter (1.32"
Distributor)
Plug in “DN” and “UP”
holes, Install Rell Port Plug
V3407 None V3430
V3020 or
V3020-01 (Mixing)
WS1.25TC Downow
Softener or Regenerating
Filter (32mm Distributor)
Injector in “DN” hole, Plug
in “UP” hole
V3407 V3174 V3430
V3020-02 or
V3020-03 (Mixing)
WS1.25TC Backwash
Only Filter (32mm
Distributor)
Plug in “DN” and “UP”
holes, Install Rell Port Plug
V3407 None V3430
V3020-02 or
V3020-03 (Mixing)
Two holes are labeled DN and UP. Check for compliance. See Table.
Push the plug(s) and/or injectors rmly in place, replace the screen and hand tighten the injector cap.