User Manual

ManualsBrandsWatts ManualsConditionersPWBWCAL3

Installation, Operation

and Maintenance Manual

Series PWBWGAC, PWBWMZ, PWBWCAL

Filter Systems

IOM-WQ-PWBWGAC-PWBWMZ-PWBWCAL

Warning

You are required to thoroughly read all installation instructions and

product safety information before beginning the installation of this

product. FAILURE TO COMPLY WITH PROPER INSTALLATION

AND MAINTENTENANCE INSTRUCTIONS COULD RESULT IN

PROPERTY DAMAGE, PERSONAL INJURY AND/OR DEATH.

Watts is not responsible for damages resulting from improper instal-

lation and/or maintenance.

Do not use with water that is microbiologically unsafe or of

unknown quality without adequate disinfection before or after

the system.

Local building or plumbing codes may require modiﬁcations to the

information provided. You are required to consult the local building

and plumbing codes prior to installation. If this information is not

consistent with local building or plumbing codes, the local codes

should be followed.

Save manual for future reference.

Refer to enclosed for operating parameters to ensure proper use

with your water supply.

Table of Contents Pages

Important Safety Information – Read All .......................2

Instructions Before Using..................................2

Filter Anatomy ..........................................3

Speciﬁcations ..........................................4

Feedwater Parameters ...................................4

Power ................................................4

Installation Considerations .................................4

Drain Flow Rates ........................................4

Setup ................................................5

Installation .............................................6

Controller..............................................7

Filter Operation .........................................7

Replenishing the Calcite Filter Media .........................7

Troubleshooting.........................................7

Limited Warranty ........................................8

PWBWGAC

PWBWMZ

PWBWCAL

PURE WATER

Summary of content (8 pages)

PAGE 1
IOM-WQ-PWBWGAC-PWBWMZ-PWBWCAL Installation, Operation and Maintenance Manual Series PWBWGAC, PWBWMZ, PWBWCAL Filter Systems PURE WATER ! Warning You are required to thoroughly read all installation instructions and product safety information before beginning the installation of this product. FAILURE TO COMPLY WITH PROPER INSTALLATION AND MAINTENTENANCE INSTRUCTIONS COULD RESULT IN PROPERTY DAMAGE, PERSONAL INJURY AND/OR DEATH.
PAGE 2
Important Safety Information – Read All ! Caution: Read and follow the information in this manual to minimize the risk of electric shock or personal injury. Important: If you are unsure about installing your Watts water filter, contact a Watts representative or consult a professional plumber. Important: This system must be installed in compliance with applicable state province and local codes, law, and regulations.
PAGE 3
Filter Anatomy 6 1 2 3 4 5 7 3 Item # Description 1 2 3 4 5 6 7 Valve Bypass Tank Distributor Filter Media (Calcite, Carbon, or Micro Z™) Faceplate/Controls Gravel Underbed
PAGE 4
Specifications Drain Flow Rates - The drain system these filters are plumbed to must be able to accept the listed drain volumes for a period of 27 minutes. Feed Water Parameters Micro Z™ Filters ! Do not use this system on water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system ! 9" X 48", 1 cubic ft. 7 gpm 10" X 54", 1.5 cubic ft. 7 gpm Minimum inlet pressure: 30 psig 12" X 52", 2 cubic ft.
PAGE 5
Setup Unpack and check the system components for damage or missing parts. Make sure that the bypass valve and plumbing yoke are properly connected to each other and to the control valve with the mounting clips. Make certain that the drain line flow control fitting is installed properly on the drain port of the control valve. Systems that are 13” in diameter and larger are not loaded with media. These systems must be loaded with media before placing into service. To load a system follow the below steps. 1.
PAGE 6
Installation 8. Fully open two (2) cold water faucets near the water filter. 9. Fully open the house main water shutoff valve. Observe a steady flow from both faucets. 1. Turn off gas or electric supply to the water heater. 2. Turn off the main water supply to pipes to be cut and drain the house water pipes. 10. Close the cold water faucets. 11. Check plumbing work for leaks and fix immediately if any are found. 3. Open both hot and cold faucets. 4.
PAGE 7
Installation continued Controller 22. Plug the unit back in to the electrical outlet and allow it to finish the flush cycle. This will take approximately 20 minutes. The factory default program settings should be adequate for most installations. See the ProFlo SXT Service Manual included with the unit for advanced programming options. 23. Set the time of day. Press and hold either the Up or Down buttons until the programming icon replaces the service icon and the parameter display reads TD.
PAGE 8
LIMITED WARRANTY: Certain Watts Pure Water products come with a limited warranty from Watts Regulator Co. Other products may have no warranty or are covered by the original manufacturer’s warranty only. For specific product warranty information, please visit www.watts.com or the published literature that comes with your product. Any remedies stated in such warranties are exclusive and are the only remedies for breach of warranty.