Instruction Manual

Watlow Series PD ■ 98 ■ Chapter 9 Device Config Table
Device Configuration > Outputs > Output 4
Output 4 - FunctionSelect the function of the output.,Configuration Output 4,,Off (0)Control (1)Event (2),Off (0),501 (R/W)
Output 4 - Output Cycle TimeSet the cycle time in seconds.,Configuration Output 4,,,,502 (R/W) (/10)
Output 4 - Control SourceSet Loop which will control this output.,Configuration Output 4,,Loop 1 (0)Loop 2 (1),Loop 1 (0),503 (R/W)
Output 4 - Output Mode Time BaseSelect method of output control as either Fixed Time Base or Variable Time Base.,Configuration Output
4,,Fixed (0)Variable (1),Fixed (0),506 (R/W)
Output 4 - StateDisplay state of output.,Monitor Device,,Inactive (0)Active (1),Inactive (0),507 (R)
Output 4 - Output DirectionSelect whether the output will be for heating (reverse action) or cooling (direct action).,Configuration Output
4,,Off (0)Heat (Indirect) (1)Cool (Direct) (2),Off (0),508 (R/W)
Output 4 - Logic OperatorSelect logic operation for event output.,Configuration Output 4,,And (0)Or (1),And (0),509 (R/W)
Output 4 - Output Source Alarm 1Set to enable Alarm 1 source.,Configuration Output 4,,No (0)Yes (1),No (0),510 (R/W)
Output 4 - Output Source Alarm 2Set to enable Alarm 2 source.,Configuration Output 4,,No (0)Yes (1),No (0),511 (R/W)
Output 4 - Output Source Alarm 3Set to enable Alarm 3 source.,Configuration Output 4,,No (0)Yes (1),No (0),512 (R/W)
Parameter Name
and Description
Web Page Your
Settings
Range Default Modbus*
(Read/write and
scaling)
Output 4 - Function
Select the function of the out-
put.
Configuration Output 4 Off (0)
Control (1)
Event (2)
Off (0) 501 (R/W)
Output 4 - Output Cycle Time
Set the cycle time in seconds.
Configuration Output 4 0.1 to 60 seconds for non-
mechanical relay outputs
1.0 to 60 seconds for me-
chanical relay outputs
1.0 second for
non-mech
relay output
10.0 seconds
for mechanical
relay output
502 (R/W) (/10)
Output 4 - Control Source
Set Loop which will control
this output.
Configuration Output 4 Loop 1 (0)
Loop 2 (1)
Loop 1 (0) 503 (R/W)
Output 4 - Output Mode
Time Base
Select method of output con-
trol as either Fixed Time Base
or Variable Time Base.
Configuration Output 4 Fixed (0)
Variable (1)
Fixed (0) 506 (R/W)
Output 4 - Low Power Scale
Set unit value for low power
scale. This setting is the
process power value when the
analog output is at minimum.
Configuration Output 4 0 to 10000 %
(two decimal places)
10000 519-520 (R/W)
(/100)
Output 4 - High Power Scale
Set unit value for high power
scale. This setting is the
process power value when the
analog output is at maximum.
Configuration Output 4 0 to 10000 %
(two decimal places)
10000 521-522 (R/W)
(/100)
Output 4 - State
Display state of output.
Monitor Device Inactive (0)
Active (1)
Inactive (0) 507 (R)
Output 4 - Output Direction
Select whether the output will
be for heating (reverse action)
or cooling (direct action).
Configuration Output 4 Off (0)
Heat (Indirect) (1)
Cool (Direct) (2)
Off (0) 508 (R/W)
Output 4 - Logic Operator
Select logic operation for event
output.
Configuration Output 4 AND (0)
OR (1)
AND (0) 509 (R/W)