User Manual
WATLOW Series 998 User’s Manual A.7
Appendix
Index
Prompt Index
A
[A3HI] alarm 3 high 5.5
[A3LO] alarm 3 low 5.5
[A4HI] alarm 4 high 5.6
[A4LO] alarm 4 low 5.6
[ACAL] retransmit calibration offset
4.31
[Addr] address 4.40
[`AL3] alarm 3 4.24
[`AL4] alarm 4 4.27
[`ALt] altitide compensation 4.14
[Amb] ambient temperature 6.9
[Anun] annunciator 4.35
[Aout] analog output 4.29
[`ArH] retransmit high limit 4.31
[`ArL] retransmit low limit 4.30
[AtSP] auto-tune set point 4.35
[`AUt] auto-tune 5.7
B
[bAUd] baud rate 4.39
C
[`C_F] celsius-fahrenheit 4.33
[`CAL] calibration menu 6.6, 6.14
[CAL1] calibration offset 1 4.8
[CAL2] calibration offset 2 4.13
[COM] Communications Menu 4.38
[COM] communications menu lock-
out 6.6
[Ct1a] cycle time, output 1A 5.12
[Ct1b] cycle time, output 1B 5.17
[Ct2a] cycle time, output 2A 5.12
[Ct2b] cycle time, output 2B 5.17
D
{dAtA} data bits and parity 4.39
[dAtE] factory ship date 6.9
[db`a] dead band A 5.12
[db`b] dead band B 5.17
[dE1A] derivative, output 1A 5.11
[dE1b] derivative, output 1B 5.16
[dE2A] derivative, output 2A 5.11
[dE2b] derivative, output 2B 5.16
[dEC1] decimal 1 4.6
[dEC2] decimal 2 4.11
[`dFL] default 6.15
[diag] Diagnostics Menu 6.8
[diag] diagnostics menu lockout
6.6
[diSP] test displays 6.12
E
[`Ei1] event input 1 4.34
[Ei1S] event input 1 status 5.4
[`Err] error latching 4.34
F
[FaIl] failure mode 4.33
[Ftr1] software filter 1 4.9
[Ftr2] software filter 2 4.14
G
[glbl] Global Menu 4.32
[glbl] global menu lockout 6.5
H
[Hy1A] hysteresis 1A 4.18
[Hy2A] hysteresis 2A 4.20
[Hy1b] hysteresis 1B 4.21
[Hy2b] hysteresis 2B 4.22
[Hys3] hysteresis 3 4.25
[HyS4] hysteresis 4 4.28
I
[`In1] input 1 4.5 - 4.6
[`In2] input 2 4.10
[InPt] Input Menu 4.2
[InPt] input menu lockout 6.5
{IntF} interface type 4.40
[It1a] integral, output 1A 5.10
[It1b] integral, output 1B 5.15
[It2a] integral, output 2A 5.10
[It2b] integral, output 2B 5.15
[itY1] input 1 module type 6.10
[itY2] input 2 module type 6.10
L
[LAt3] latching 3 4.26
[LAt4] latching 4 4.28
[Lin2] linearization 2 4.14
[`LOC] front panel lockout 6.3
O
[Ot1A] output 1A 4.17
[Ot1b] output 1B 4.21
[Ot2A] output 2A 4.19
[Ot2b] output 2B 4.22
[`Ot3] output 3 4.23
[Ot3s] output 3 status 5.4
[`Ot4] output 4 4.27
[Ot4s] output 4 status 5.4
[OtPt] Output Menu 4.16
[OtPt] output menu lockout 6.5
[OtY1] output 1 module type 6.11
[OtY2] output 2 module type 6.11
[OtY3] output 3 module type 6.11
[OtY4] output 4 module type 6.11
P
[Pb1a] proportional band, output 1A
5.9
[Pb1b] proportional band, output 1B
5.14
[Pb2a] proportional band, output 2A
5.9
[Pb2b] proportional band, output 2B
5.14
[PIda] Channel A PID Menu 5.8
[Pida] PID A menu lockout 6.4
[PIdb] Channel B PID Menu 5.13
[Pidb] PID B menu lockout 6.4
[PlOC] Panel Lockout Menu 6.2
[Prc3] process 3 4.30
[PrcA] process A 4.20
[Prcb] process B 4.23
{Prot} protocol type 4.40
R
[rA1A] rate, output 1A 5.11
[rA1b] rate, output 1B 5.16
[rA2A] rate, output 2A 5.11
[rA2b] rate, output 2B 5.16
[rE1A] reset, output 1A 5.10
[rE1b] reset, output 1B 5.15
[rE2A] reset, output 2A 5.10
[rE2b] reset, output 2B 5.15
[`rH1] range high 1 4.7 - 4.8
[`rH2] range high 2 4.11 - 4.12
[`rL1] range low 1 4.7 - 4.8
[`rL2] range low 2 4.11 - 4.12
[rp`a] ramping function for channel A
4.35
[rp`b] ramping function for channel B
4.36
[rt`a] ramp rate for channel A 4.36
[rt`b] ramp rate for channel B 4.36
[rtd1] RTD calibration curve 1 4.9
[rtd2] RTD calibration curve 2 4.13
[`rSt] restore 6.15
S
[SIL3] silencing 3 4.26
[SIL4] silencing 4 4.29
[Sn--] serial number 6.9
[SOFt] software revision 6.9
[SP2A] set point 2A 5.3
[SP2b] set point 2B 5.3
[`SyS] System Menu 5.2
[`SyS] system menu lockout 6.4
T
[tout] test outputs 6.12