User guide

Watlow Series 97 Appendix ■ A.25
Series 97 Software Map
[``97] Process Value
[Safe]
Home Page
Limit Status
Setup Page
[InP1] Input 1 Menu
[`SEt] Setup Page
[SEn1] Sensor Type 1___________
_
[In`1] Input 1 _________________
_
[rL`1] Range Low 1 ____________
_
[rh`1] Range High 1 ____________
_
[dEC1] Decimal 1 _______________
_
[Ftr1] Input Software Filter 1 _____
_
[InP2] Input 2 Menu
[`SEt] Setup Page
[In`2] Input 2 _________________
_
[E`Fn] Event Function ___________
_
[E`cn] Event Condition __________
_
[Out1] Ouput 1 Menu
[`SEt] Setup Page
[LSid] Set Limit Active Sides _____
_
[LhyS] Limit Hysteresis __________
_
[Out2] Ouput 2 Menu
[`SEt] Setup Page
[Ot`2] Output 2 ________________
_
[hys2] Alarm Hysteresis 2 ________
_
[LAt2] Latching 2 ______________
_
[sil2] Silencing 2 ______________
_
[Sid2] Alarm Active Sides 2 ______
_
[Lgc2] Alarm Logic 2 ____________
_
[Anu2] Alarm Annunciation 2 ______
_
[Out3] Ouput 3 Menu
[`SEt] Setup Page
[Ot`3] Output 3 ________________
_
[hys3] Alarm Hysteresis 3 ________
_
[LAt3] Latching 3 ______________
_
[sil3] Silencing 3 ______________
_
[sid3] Alarm Active Sides 3 ______
_
[Lgc3] Alarm Logic 3 ____________
_
[Anu3] Alarm Annunciation 3 ______
_
[Out4] Ouput 4 Menu
[`SEt] Setup Page
[Ot`4] Output 4 ________________
_
[hys4] Alarm Hysteresis 4 ________
_
[LAt4] Latching 4 ______________
_
[sil4] Silencing 4 ______________
_
[Sid4] Alarm Active Sides 4 ______
_
[Lgc4] Alarm Logic 4 ____________
_
[Anu4] Alarm Annunciation 4 ______
_
[Aout] Analog Output 4 __________
_
[Prc4] Process 4 Type __________
_
[A`hi] Analog Output High _______
_
[A`lo] Analog Output Low _______
_
[ACAL] Analog Output Offset ______
_
[BaUd] Baud Rate ______________
_
[Addr] Address ________________
_
[diSP] Display Menu
[`SEt] Setup Page
[UdSP] Upper Display____________
_
[UP`L] Upper Display
User Limit Message_______
_
[LdSP] Lower Display____________
_
[Lo`S] Lower Display
User Safe Message_______
_
[Lo`L] Lower Display
User Limit Message___
____
_
[GLbL] Global Menu
[`SEt] Setup Page
[C-F`] C or F __________________
_
[`Err] Input Error Latching _______
_
Operations Page
[LIM] Limit Menu
[OPEr] Operations Page
[L~Lo] Low Limit Set Point ________
_
[L~hi] High Limit Set Point ________
_
[CAL1] Calibration Offset __________
_
[Mon] Monitor Menu
[OPEr] Operations Page
[Pr1`] Process 1________________
_
[L`St] Limit Status_______________
[AL`2] Alarm 2 Status ____________
_
[AL`3] Alarm 3 Status ____________
_
[AL`4] Alarm 4 Status ____________
_
[E`St] Event Input Status _________
_
[ALM] Alarm Menu
[OPEr] Operations Page
[A2Lo] Alarm 2 Low ______________
_
[A2hi] Alarm 2 High _____________
_
[A3Lo] Alarm 3 Low ______________
_
[A3hi] Alarm 3 High _____________
_
[A4Lo] Alarm 4 Low ______________
_
[A4hi] Alarm 4 High _____________
_
Factory Page
[`LOC] Lockout Menu
[FctY] Factory Page
[OPEr] Operations Page Mode ______
_
[`SEt] Setup Page Lock __________
_
[`CAL] Calibration Menu Lock ______
_
[dIAg] Diagnostics Menu
[FctY] Factory Page
[MdL] Model Number ____________
_
[dAtE] Date of Manufacture ________
_
[`Sn1] Serial Number 1 ___________
_
[`Sn2] Serial Number 2 ___________
_
[Soft] Software ID Number ________
_
[`rEu] Software Revision __________
_
[ity2] Input 2 Hardware Enabled____
_
[OTY1] Output 1 Hardware _________
_
[Oty2] Output 2 Hardware _________
_
[Oty3] Output 3 Hardware _________
_
[Oty4] Output 4 Hardware _________
_
[tout] Test Output _______________
_
[dISP] Test Displays ______________
_
[hrES] High Resolution ___________
_
[AMb] Ambient Temperature _______
_
[Acnt] Ambient A-D Counts ________
_
[cnt1] Channel 1 A-D Counts ______
_
[cnt2] Channel 2 A-D Counts ______
_
[LinE] Line Frequency ____________
_
Enter your settings on a photocopy
of this page.
The Factory Page also includes
calibration parameters that are
not necessary for everyday use of
the controller. Calibration para-
meters and procedures are
explained in the Appendix.