Manual

Using the Manual ■
Units Type [Unit] °C or °F [`C-F] Output 1 [Ot`1] Output 2 [Ot`2] Sensor Type [Sen1] Input 1 [In`1] Range High 1 [rh`1] Range Low [rL`1] Decimal 1 [DeC1] HPL Above [PL`A] HPL Below [PL`b] Input 2 [In`2] Alarm Type 2, 3, 4
Units Type [Unit]
°C or °F [`C-F]
Failure Mode [Fail]
Output 1 [Ot`1]
Output 2 [Ot`2]
Output 3 [Ot`3]
Output 4 [Ot`4]
Manual Default Power [man] OO OO
Sensor Type [Sen1]
Input 1 [In`1] O
Range High 1 [rh`1] CDDC
Range Low [rL`1] CDDC
Decimal 1 [DeC1] DD
Calibration Offset 1 [Cal1] CDDC
Input Software Filter 1 [Ftr1] DD O
Power Limit Set Point [PLSP] C D DOOC
High Power Limit Above [PL`A] OO
High Power Limit Below [PL`b] OO
Input 2 [In`2]
Event Function [E`fn] O
Event Condition [E`cn] O
Range High 2 [rh`2] CCD
Range Low 2 [rL`2] CCD
Calibration Offset 2 [CAL2] CCD
Analog Output 4 [Aout] DD
Analog Output High [A`hi] CDDC
Analog Output Low [A`lo] CDD C
Analog Output Offset [ACAL] CDDC
Ramping Mode [``rP]
Ramp Scale [rP`S]
Ramp Rate [rAtE]
Alarm Type 2, 3, 4 [Aty2] 3] 4]
Alarm Hysteresis 2, 3, 4 [Ahy2] 3] 4] CDDC
Latching 2, 3, 4 [Lat2] 3] 4]
Alarm Silencing 2, 3, 4 [Sil2] 3] 4]
Alarm Active Sides 2, 3, 4 [Sid2] 3] 4]
Alarm Logic 2, 3, 4 [Lgc2] 3] 4]
Alarm 2, 3, 4 High [A2hi] 3] 4] CDDC O
Alarm 2, 3, 4 Low [A2lo] 3] 4] CDDC O
Propband 1, 2 [Pb1] 2] CDDC
Integral 1, 2 [It`1] 2] C
Reset 1, 2 [rE`1] 2] C
Derivative 1, 2 [dE`1] 2]
Rate 1, 2 [rA`1] 2]
Burst 1, 2 [brS1] 2]
Cycle Time 1, 2 [Ct`1] 2]
Dead Band 1, 2 [db`1] 2] CDDC
Hysteresis 1, 2 [Hys1] 2] CDDC
Auto-Manual Operations Mode [A-M]
Event Set Point [E`SP] C D DOOC
Set Point 2 [`SP2] C DDOOC
Set Point Lock [``SP] C D DOOC
Manual Set Point O O O O
Changing this
Affects this
Key:
D = Changing will change
the default
C = Changing will convert
the
temperature scale
O = Other effect
Table 3.2 — Set up
parameters in this
order.