Manual

ManualsBrandsWatlow ManualsSensorsSeries 96

Series 96 Software Map

[``96] Process 1 Value

[``96]

[``96] Custom Menu**…

[``P1]

Home Page

Set Point Value,

Remote Set Point Value

or Percent Output Value

Setup Page

[InP1] Input 1 Menu

[`SEt] Setup Page

[SEn1] Sensor Type _______________

[In`1] Input Type 1 _______________

[rL`1] Range Low 1_______________

[rh`1] Range High 1 ______________

[dEC1] Decimal 1 _________________

[Ftr1] Input Software Filter 1 _______

[InP2] Input 2 Menu

[`SEt] Setup Page

[In`2] Input 2** __________________

[rL`2] Range Low 2** _____________

[rh`2] Range High 2**_____________

[CAL2] Calibration Offset 2**_________

[E`Fn] Event Function _____________

[E`cn] Event Condition ____________

[absp] Abort Set Point* ____________

[Out1] Output 1 Menu

[`SEt] Setup Page

[Ot`1] Output 1 __________________

[Prc1] Process Type 1_____________

[Out2] Output 2 Menu

[`SEt] Setup Page

[Ot`2] Output 2 __________________

[Prc2] Process Type 2_____________

[AtY2] Alarm Type 2_______________

[AhY2] Alarm Hysteresis 2 __________

[LAt2] Latching 2 _________________

[SIL2] Silencing 2 ________________

[Sid2] Alarm Active Sides 2_________

[Lgc2] Alarm Logic 2 ______________

[Anu2] Alarm Annunciation 2 ________

[Out3] Output 3 Menu

[`SEt] Setup Page

[Ot`3] Output 3 __________________

[AtY3] Alarm Type 3_______________

[Ahy3] Alarm Hysteresis 3 __________

[LAt3] Latching 3 _________________

[SIL3] Silencing 3_________________

[Sid3] Alarm Active Sides 3 _________

[Lgc3] Alarm Logic 3 _______________

[Anu3] Alarm Annunciation 3_________

[Out4] Output 4 Menu

[`SEt] Setup Page

[Ot`4] Output 4 __________________

[AtY4] Alarm Type 4 _______________

[Ahy4] Alarm Hysteresis 4 __________

[LAt4] Latching 4 _________________

[SIL4] Silencing 4 _________________

[Sid4] Alarm Active Sides 4_________

[Lgc4] Alarm Logic 4 _______________

[Anu4] Alarm Annunciation 4 _________

[Aout] Analog Output 4 _____________

[Prc4] Process Type 4_____________

[A`hi] Analog Output High __________

[A`lo] Analog Output Low __________

[ACAL] Analog Output Offset _________

[BaUd] Baud Rate _________________

[Addr] Address ___________________

[gLbL] Global Menu

[`SEt] Setup Page

[Unit] Units Type_________________

[`C-F] C or F ____________________

[`Err] Input Error Latching _________

[FAIL] Failure Mode**______________

[MAn] Manual Default Power** ______

[PLSP] Power Limit Set Point ________

[PL`A] High Power Limit Above ______

[PL`b] High Power Limit Below ______

[``rP] Ramping Mode**____________

[rP`S] Ramp Scale** ______________

[ratE] Ramp Rate**_______________

[OPLP] Open Loop Detect __________

[ptyP] Program Type* _____________

perat

ons

age

[Mon] Monitor Menu

[OPEr] Operations Page

[Pr2`] Process 2**__________________

[Pcnt] Percent Output _______________

[rPSP] Ramping Set Point**___________

[E`St] Event Input Status ____________

[USEr] User Menu

[OPEr] Operations Page

[A-M] Auto-Manual Operations Mode** __

[`Aut] Auto-tune ___________________

[AtSP] Auto-tune Set Point____________

[`SP2] Set Point 2** _________________

[E`SP] Event Set Point**_____________

[`L-r] Local or Remote Mode**________

[CAL1] Calibration Offset _____________

[PId1] PID 1 Menu

[OPEr] Operations Page

[Pb`1] Propband 1 __________________

[It`1] Integral 1____________________

[rE`1] Reset 1 _____________________

[dE`1] Derivative 1__________________

[rA`1] Rate 1 ______________________

[brS1] Burst 1______________________

[Ct`1] Cycle Time 1 _________________

[hYS1] Hysteresis 1 _________________

[db`1] Dead Band 1 ________________

[PID2] PID 2 Menu

[OPEr] Operations Page

[Pb`2] Propband 2 __________________

[It`2] Integral 2 ___________________

[rE`2] Reset 2 _____________________

[dE`2] Derivative 2 _________________

[rA`2] Rate 2 ______________________

[brS2] Burst 2 _____________________

[Ct`2] Cycle Time 2 ________________

[hYS2] Hysteresis 2 _________________

[db`2] Dead Band 2 ________________

[ALM] Alarm Menu

[OPEr] Operations Page

[A2Lo] Alarm 2 Low _________________

[A2hi] Alarm 2 High _________________

[A3Lo] Alarm 3 Low _________________

[A3hi] Alarm 3 High _________________

[A4Lo] Alarm 4 Low _________________

[A4hi] Alarm 4 High _________________

Factory Page

[CUSt] Custom Menu**

[FctY] Factory Page

[``P1] __________________________

[``P2] __________________________

[``P3] __________________________

[``P4] __________________________

[``P5] __________________________

[``P6] __________________________

[``P7] __________________________

[``P8] __________________________

[``P9] __________________________

[`P10] __________________________

[`P11] __________________________

[`P12] __________________________

[`P13] __________________________

[`P14] __________________________

[`P15] __________________________

[`P16] __________________________

[`LOC] Lockout Menu

[FctY] Factory Page

[``SP] Set Point Lock ______________

[prog] Program Menu Lock* ________

[CuSt] Custom Menu Lock** ________

[OPEr] Operations Page Mode _______

[`SEt] Setup Page Lock____________

[`CAL] Calibration Menu Lock

________

[dIAg] Diagnostics Menu

[FctY] Factory Page_______________

[MdL] Model Number______________

[dAtE] Date of Manufacture _________

[`Sn1] Serial Number 1

____________

[`Sn2] Serial Number 2 ____________

[Soft] Software ID Number _________

[ItY2] Input Type 2 ________________

[`rEu] Software Revision ___________

[OTY1] Output 1 Hardware __________

[Oty2] Output 2 Hardware __________

[Oty3] Output 3 Hardware __________

[Oty4] Output 4 Hardware___________

[tout] Test Output_________________

[dISP] Test Displays _______________

[hrES] High Resolution_____________

[AMb] Ambient Temperature ________

[Acnt] Ambient A-D Counts _________

[cnt1] Channel 1 A-D Counts _______

[cnt2] Channel 2 A-D Counts _______

[tSht] Communications Test/

Troubleshooting

____________

[LinE] Line Frequency _____________

Enter your settings on a photo-

copy of this page.

The Factory Page also includes

calibration parameters that are

not necessary for everyday use

of the controller. Calibration

parameters and procedures are

explained at Watlow’s web site,

http://www.watlow.com/litera-

ture/prodtechinfo. Search on 96

calibration manual.

*Menu added if ramping version

of the controller is selected

(96__-____-AA__).

**Menu removed if ramping

version of the controller is

selected (96__-____-AA__).

Program Menu*

(see pg. 7.1)