User guide

Appendix Watlow Power Series ■ A.13
Prompt Index
A
[``Ad] Select Analog to Digital Channel 6.19
[Addr] Unit Address Select 6.12
[ALÇ`] Heat Sink Alarm Temp 6.18
[aLÇ`] Heat Sink Over Temperature Alarm
Temperature 6.10
[a| lgc] Active Relay State 6.10
[ALgo] Power Control Algorithm Select 6.5
[Algo] Setup Control Algorithm Menu 6.5-
6.6
{`Alr} Alarms Setup Menu Lockout 6.16
[`ALr] Setup Alarms Configuration Menu 5.7,
6.10-6.11
B
[baud] Unit Baud Rate Select 6.12
[BAuP] Backup Data Set 6.15
[bl`U] Baseline Voltage Read/Adjust 6.7
C
[```Ç] Heat Sink Temperature (°C) 6.18
[CALA] Calibrate Analog Input Request 6.21
[CALr] Cal Retransmit Request 6.22
[`Cf9] Retransmit Configuration Select 6.12
{`CIn} Analog Input Factory Menus Lockout
6.16
[CIn1] [CIn2] [CIn3] Calibrate Analog Input
Signal Zone 1, 2, or 3 Menus 6.21-6.22
[CL`A] Current Limit Set Point (A) 5.5, 6.9
[`CLi] Current Limit Select (On/Off) 5.5, 6.8
{COM} Comms Setup Menu Lockout 6.16
[COM] Setup Comms Configuration Menu
6.12
[Cnts] Read Selected Analog to Digital
Counts 6.19
[cont] dc contactor 5.2
[C| rtr] Retransmit Cal Factory Menu Lockout
6.16
[Crtr] Calibrate Retransmit Menu 6.22
[`Ctr] Control Setup Menus Lockout 6.16
[Ctr1] [Ctr2] [Ctr3] Setup Control Zone 1,
2, and 3 Menus 6.6-6.8
[`Cur] Load Current (Amps) rms 6.2
[Cur1], [Cur2], [Cur3] Load Current (Amps)
rms 6.3, 6.4
[Cur–] Maximum Amps Retransmit 6.13
[Cur_] Minimum Amps Retransmit 6.13
[C| Wd] Comms Watchdog Alarm Configura-
tion 6.11
D
[dAtA] System Data Factory Menu Lockout
6.17
[dATA] System Data Manipulation Menu
6.15-6.16
[date] Manufactured Date (yymm) 6.17
[dFLt] Default Data Set 6.15
[dFlt] Default Numeric Input Signal (%) 6.6
[diAg] Diagnostics Factory Menu Lockout 6.17
[diag] Diagnostics Menu 6.19-6.20
[dIsp] Display Test 6.20
EF
[fcty] Factory Mode Request 6.20
[Fcty] Factory Page 6.14 - 6.22
[Freq] Frequency Out of Tolerance Alarm
Configuration 6.11
[FrEq] Line Frequency (Hz) 6.1
[`FTB] Fixed Time Base 5.1
[`FTB] Fixed Time Base (Sec) 6.5
G
[glbl] Global Alarm Configuration 5.7, 6.10
{gLOC} Global Lockout 5.6, 6.16
H
[`HbC] Heater Bakeout Overcurrent Trip
6.8
[`Hbo] Heater Bakeout Select (On/Off) 5.4,
6.8
[`Hbt] Heater Bakeout Timeout 6.2
[Hbt1] [Hbt2] [Hbt3] Heater Bakeout Time-
out 6.2, 6.3
[HI`Ç] Record High Heat Sink Temp 6.18
[HrS–] Accum Hours (10K - 100M) 6.18
[HrS_] Accum Hours (0 - 9999) 6.18
[`HUa] Load Power (kVA) 6.2, 6.4
HUA–] Maximum kVA Retransmit 6.13
[HUA_] Minimum kVA Retransmit 6.13
[HUa1] [HUa2] [HUa3] Load Power (kVA) 6.3,
6.4
[HUer] Hardware Version 6.17
I J K
[ICur] Inductive Current 6.9
[``In] Analog (mA or V) or Numeric (%)
Input Signal 6.1, 6.4
[``In] Input Signal Method Select (dig, mA,
volt) 6.6
[``In] Select Discrete Input 6.20
[In`1], [In`2], [In`3] Analog (mA or V) or
Numeric (%) Input Signal 6.2, 6.3
[Indf] Inductive Load Factor Request 6.9
[Info] Unit Information Menu 6.17-6.18
L
[l!a1] Line Loss Alarm, Most Recent 6.19
[l!a2] [l@a2] [l#a2] Line Loss 6.19
[l!a3] [l@a3] [l#a3] Alarm Type 6.19
[l@a1] Line Loss Alarm, Previous 6.19
[l#a1] Line Loss Alarm, Least Recent 6.19
[Lbal] Load Balance Alarm Config. 6.11
[Ldif] Load Balance Percentage 6.11
[Line] Line Loss Alarm Config. 6.10
[LoAd] Load Activity Indicator 6.1
[`LOC] Global/Menu Lockouts Menu 6.16-6.17
[lrn| A] Learn Input Learn Request (Hi, Lo)
6.7
[lrn| U] Baseline Voltage Learn Request 6.7
M N
[Min] Heater Bakeout Select Time 5.4, 6.8
[nna–] Adjust High mA Cal Point 6.21
[nna_] Adjust Low mA Cal Point 6.21
[nna–] Retransmit Cal mA High 6.22
[nna_] Retransmit Cal mA Low 6.22
[nna–] Set Analog Input High Current (mA)
6.6
[nna_] Set Analog Input Low Current (mA)
6.6
[nUOL] Enable NVOL Storage 6.16
O
[Open] Heater Open Alarm Config. 6.10
[`OPt] Config. Installed Options 6.18
{`Opt} Options Setup Menus Lockout 6.16
[Opt1] [Opt2] [Opt3] Setup Options Zone 1,
2, and 3 Menus 6.8-6.9
[``OT] Heat Sink Over Temperature Alarm
Configuration 6.10
[``OU] Over Voltage Alarm Config. 6.11
[`Out] Output Power (%) 6.2, 6.4
[Out1], [Out2], [Out3] Output Power (%)
6.2, 6.3
P Q
[p| bAl] Phase Balance Alarm Config. 6.11
[Phas] Display Phase 6.4
[PhaS] Retransmit Phase Select 6.13
[Ph2t] Phase Angle 5.2
[`PW] Factory Password 6.20
[`PW] Factory Password Entry 6.20
[PWr] Watchdog Failure Output Power
Select (%) 6.12
R
[ratA] Unit Current Rating (Amps) 6.18
[rATE] Maximum Rate of Change (%/100msec)
6.8
[ratU] Unit Voltage Rating (Volts) 6.17
[rdLY] Reactance Delay 6.8
[reSt] Restore Data Set 6.15
[rEtr] Retransmit Set Test Word 6.20
{retr} Retransmit Setup Menu Lockout 6.16
[rEtr] Setup Retransmit Configuration Menu
6.12-6.14
[rt| C–] Set Retransmit Output High Current
(mA) 6.13
[rt| C_] Set Retransmit Output Low Current
(mA) 6.13
[rt| U–] Set Retransmit Output High Voltage
(Volts) 6.14
[rt| U_] Set Retransmit Output Low Voltage
(Volts) 6.14
S
[Sbld] Software Build Number 6.17
[sdÇ`] Factory Safety Shutdown Temp 6.18
[`seC] Watchdog Timeout (Sec) 6.12
[`Set] Setup Page Select 6.5-6.13
[`Sn–] Unit Serial Number High Digits 6.17
[`Sn_] Unit Serial Number Low Digits 6.17
[Soft] Soft Start 5.3
[Soft] Soft Start Time (Sec) 6.8
[SUEr] Software Version 6.17
T
[`tol] Heater Tolerance Alarm Configuration
6.10
[tol–] High Tolerance Set Point (A) 6.9
[tol_] Low Tolerance Set Point (A) 6.9
[type] Load Type Select 6.7
[type] Retransmit Type Select 6.12
U V W X Y Z
[`UAL] Read Selected Input Value 6.20
[``UC] Line Voltage Compensation 6.6
[``UC] Voltage Compensation Alarm
Configuration 6.11
[`UoL] Line Potential (Volts) rms 6.2
[Uol1], [Uol2], [Uol3] Line Potential (Volts)
rms 6.3, 6.4
[Uol–] Adjust High V Cal Point 6.21
[Uol_] Adjust Low V Cal Point 6.21
[Uol–] Retransmit Cal Volts High 6.22
[Uol_] Retransmit Cal Volts Low 6.22
[Uol–] Set Analog Input High Voltage (Volts)
6.7
[Uol_] Set Analog Input Low Voltage (Volts)
6.6
[Urtb] Variable Time Base 5.2
[`Wd] Watchdog Select (On/Off) 6.12
[2onC] Number Zones Configured 6.18
[2one] Retransmit Zone Select 6.13
[2one] Zone Display Selection 6.2, 6.3