User guide

4.4 ■ Watlow Power Series Navigation and Software, Chapter 4
**NOTE: These menus and display prompts are only viewable in the Factory Mode using a password.
NOTE: For an explanation of the parameters in the Setup Page, (range information, Modbus address, and conditions for the
parameter to appear), see Chapter Six, Parameters, pp. 6.5-6.14; for information on the Factory Page, see pp. 6.14-6.22.
[dAta] System Data Manipulation
[FctY]% ¨[baup]¨[dflt]¨[rEst]¨[nUOl]¨
%Î
%Ó
[`Loc] Global/Menu Lockouts
[[FctY]% ¨[gloc]¨[`Ctr]¨[`OPt]¨[`Alr]¨[COm]¨[retr]¨[`CIn]¨[C|`rtr]¨[dAta]¨[diAg]¨
%Î
%Ó
[InFo] Unit Information
[FctY]% ¬®[`sn–]¬®[`sn_]¬®[date]¬®[HUEr]¬®[SUEr]¬®[sbld]¬®[ratU]¬®[rata]¬®[2onC]¬®[`Opt]¬®[```Ç]¬®
Î
%Ó
%%% ¬®[Hrs_]¬®[Hrs–]¬®[HIÇ`]¬®[sdÇ`]¬®[AlÇ`]
[diAg] Diagnostics
[[FctY]% ¨[``Ad]¨[Cnts]¨[l!A1]¨[l!A2]¨[l!A3]¨[l@A1]¨[l@A2]¨[l@A3]¨[l#A1]¨[l#A2]¨[l#A3]¨
Î
%Ó%
¨[retr]¨[`UAL]¨[``In]¨[dIsp]
%%
[`pw] Factory Password
[FctY]
% ¨[`pw]¨[fcty]¨
%
Î
%Ó
[CIn1] Calibrate Analog Input Signal Zone 1**
[FctY] % ¬®[nnA_]¬®[nnA–]¬®[UoL_]¬®[UoL–]¬®[Cala]¬®
%
Î
%Ó
[CIn2] Calibrate Analog Input Signal Zone 2**
[FctY] % ¬®[nnA_]¬®[nnA–]¬®[UoL_]¬®[UoL–]¬®[Cala]¬®
%
Î
%Ó
[CIn3] Calibrate Analog Input Signal Zone 3**
[FctY] % ¬®[nnA_]¬®[nnA–]¬®[UoL_]¬®[UoL–]¬®[Cala]¬®
%
Î
%Ó
[Crtr] Calibrate Retransmit**
[FctY]% ¬®[nnA_]¬®[nnA–]¬®[UoL_]¬®[UoL–]¬®[Calr]¬®
%Î
%Ó
Factory Page Menus
Use the Increment/Decrement keys ( Ó Î ) to select a menu
within the Factory Page. The menu appears in the upper display.
Use the Left/Right arrow keys (
¬ ® ) to select a parameter
within a menu. The parameter appears in the bottom display.
Use the Increment/Decrement keys ( Ó Î ) to select a value,
either alpha or numeric, within a parameter. The value appears
in the upper display.
*NOTE: This prompt will only appear in [Ctr1], and if the controller is 3 phase.
[algo] Control Algorithm
[`set]
% ¨[algo]¨[`ftb]¨[``UC]¨
%Î% Î
%Ó% Óv
[cont] Î [`OFF] Î [`ftb] Î Urtb] Î [pH2t]
%
[Ctr1] Setup Control Zone 1
[`set]
% ¬®[``In]¬®[%dflt]¬®[nna_]¬®[nna–]¬®[Uol_]¬®[Uol–]¬®[lrn|``A]¬®[bl`U]¬®[lrn|``U]¬®[type]¬®[rate]¬®[soft]¬®[rdly]¬®
%Î
%Ó
[Opt1] Setup Options Zone 1
[`set]
% ¬®[`Hbo]¬®[Min]¬®[`HbC]¬®[`Cli]¬®[`Cla]¬®[tol_]¬®[toL–]¬®[Indf]¬®[1Cur]¬®
%Î
%Ó
[Ctr2] Setup Control Zone 2
[`set]
% ¬®[``In]¬®[dflt]¬®[nna_]¬®[nna–]¬®[Uol_]¬®[Uol–]¬®[lrn|``A]¬®[bl`U]¬®[lrn|``U]¬®[rate]¬®[soft]¬®
%
Î
%Ó
[Opt2] Setup Options Zone 2
[`set]
% ¬®[`Hbo]¬®[Min]¬®[`HbC]¬®[`Cli]¬®[`Cla]¬®[tol_]¬®[toL–]¬®[Indf]¬®[1Cur]¬®
%Î
%Ó
[Ctr3] Setup Control Zone 3
[`set]
% ¬®[``In]¬®[dflt]¬®[nna_]¬®[nna–]¬®[Uol_]¬®[Uol–]¬®[lrn|A]¬®[bl`U]¬®[lrn|``U]¬®[rate]¬®[soft]¬®
%
Î
%Ó
[Opt3] Setup Options Zone 3
[`set]
% ¬®[`Hbo]¬®[Min]¬®[`HbC]¬®[`Cli]¬®[`Cla]¬®[tol_]¬®[toL–]¬®[Indf]¬®[1Cur]¬®
%Î
%Ó
[`aLr] Setup Alarms Configuration
[`set]
% ¬®[A|``l9c]¬®[glbl]¬®[Open]¬®[`tol]¬®[``Ot]¬®[`aLÇ]¬®[Line]¬®[p|bal]¬®[lbal]¬®[ldif]¬®[freq]¬®
%Î
%Ó
% %%% ¨[C|``wd]¨[``OU]¨[``UC]
[COm] Setup Comms Configuration
[`set]
% ¨[addr]¨[baUd]¨[`wd]¨[`seC]¨[pwr]¨
%Î
%Ó
[retr] Setup Retransmit Configuration
[`set]
% ¬®[`Cfg]¬®[type]¬®[pha5]¬®[2one]¬®[Cur_]¬®[Cur–]¬®[HUa_]¬®[HUa–]¬®[rt|``C_]¬®[rt|``C–]¬®[rt|``U_]¬®[rt|``U–]¬®
%Î
%Ó
Setup Page Menus
Use the Increment/Decrement keys ( Ó Î ) to select a menu
within the Setup Page. The menu appears in the upper display.
Use the Left/Right arrow keys (
¬ ® ) to select a parameter within a
menu. The parameter appears in the bottom display.
Use the Increment/Decrement keys (
Ó Î ) to select a value, either alpha
or numeric, within a parameter. The value appears in the upper display.
*