User guide

Watlow EZ-ZONE
®
RMH Module • 55 • Chapter 4 Setup Page
RM High Density Module • Setup Page
Display
Parameter Name
Description
Range Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Probus
Index
Parameter
ID
Data
Type
&
Read/
Write
[SFn;E]
[SFn.E]
Process Value (1 to 16)
Source Function E
Set the type of function
that will be used for this
source.
[nonE] None (61)
[ALM] Alarm (6)
[`CPE] Compare (230)
[`Ctr] Counter (231)
[`dio] Digital I/O (1142)
[Ent;A] Profile Event Out A
(233)
[Ent;b] Profile Event Out B
(234)
[Ent;C] Profile Event Out C
(235)
[Ent;d] Profile Event Out D
(236)
[Ent;E] Profile Event Out E
(247)
[Ent;F] Profile Event Out F
(248)
[Ent;g] Profile Event Out G
(249)
[Ent;h] Profile Event Out H
(250)
[`FUn] Function Key (1001)
[`lgC] Logic (239)
[tMr] Timer (244)
[`uAr] Variable (245)
None 8228
[offset 70]
0x7E
(126)
1 to 16
5
- - - - 26005 uint
RWES
[`Si;E]
[ Si.E]
Process Value (1 to 16)
Source Instance E
Set the instance of the
function selected above.
1 to 250 1 8238
[offset 70]
0x7E
(126)
1 to 16
0x0A (10)
- - - - 26010 uint
RWES
[`s2;E]
[ SZ.E]
Process Value (1 to 16)
Source Zone E
Set the zone of the function
selected above.
0 to 16 0 8248
[offset 70]
0x7E
(126)
1 to 16
0x0F (15)
- - - - 26015 uint
RWES
[``C;p]
[ SZ.E]
Process Value (1 to 16)
Cross Over Point
Enter a value where the
Output Value switches
from Source A to Source
B value. This applies only
when the Process function
is set to Cross Over.
-1,999.000 to 9,999.000 units
or °F
-1,128.333 to 5,537.223 °C
100.0 8266
[offset 70]
0x7E
(126)
1 to 16
0x18 (24)
- - - - 26024 float
RWES
[``C;b]
[ SZ.E]
Process Value (1 to 16)
Cross Over Band
Enter a band centered
about the Cross Over
Point where Output Value
switches from Source A to
Source B Value. This ap-
plies only when the Process
function is set to Cross
Over.
-1,999.000 to 9,999.000 units
or °F
-1,128.333 to 5,537.223 °C
10.0 8268
[offset 70]
0x7E
(126)
1 to 16
0x19 (25)
- - - - 26025 float
RWES
Note:
Some values will be rounded off to fit in the four-character display.
Full values can be read with other interfaces.
Note:
If there is only one instance of a menu, no submenus will appear.
** These parameters/prompts are available in these menus with firmware revisions 6.0 and
above.
R: Read
W: Write
E: EEPROM
S: User
Set