User guide

Watlow EZ-ZONE
®
RMH Module • 42 • Chapter 3 Operations Page
RM High Density Module • Operations Page
Display
Parameter Name
Description
Range Default
Modbus
Relative
Address
CIP
Class
Instance
Attribute
hex (dec)
Probus
Index
Parameter
ID
Data
Type
& Read/
Write
[`C;SP]
[ C.SP]
Control Loop (1 to 16)
Closed Loop Set Point
Set the set point that the
controller will automati-
cally control to.
Low Set Point to High Set
Point (Setup Page)
75.0°F
or
units
24.0°C
5220
[offset 80]
0x6B
(107)
1 to 16
1
39 7001 float
RWES
[`id;S]
[ id.S]
Control Loop (1 to 16)
Idle Set Point
Set a closed loop set point
that can be triggered by
an event state.
Low Set Point to High Set
Point (Setup Page)
75.0°F
or
units
24.0°C
5236
[offset 80]
0x6B
(107)
1 to 16
9
40 7009 float
RWES
[`h;Pb]
[ h.Pb]
Control Loop (1 to 16)
Heat Proportional Band
Set the PID proportional
band for the heat outputs.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
25.0°F
or
units
14.0°C
4110
[offset 70]
0x97
(151)
1 to 16
6
55 8009 float
RWES
[`h;hy]
[ h.hy]
Control Loop (1 to 16)
Heat Hysteresis
Set the control switching
hysteresis for on-off con-
trol. This determines how
far into the “on” region
the process value needs
to move before the output
turns on.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
3.0°F or
units
2.0°C
4120
[offset 70]
0x97
(151)
1 to 16
0xB (11)
56 8010 float
RWES
[`C;Pb]
[ C.Pb]
Control Loop (1 to 16)
Cool Proportional Band
Set the PID proportional
band for the cool outputs.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
25.0°F
or
units
14.0°C
4112
[offset 70]
0x97
(151)
1 to 16
7
57 8012 float
RWES
[`C;hy]
[ C.hy]
Control Loop (1 to 16)
Cool Hysteresis
Set the control switching
hysteresis for on-off con-
trol. This determines how
far into the “on” region
the process value needs
to move before the output
turns on.
0.001 to 9,999.000°F or
units
0.001 to 5,555.000°C
3.0°F or
units
2.0°C
4122
[offset 70]
0x97
(151)
1 to 16
0xC (12)
58 8013 float
RWES
[``ti]
[ ti]
Control Loop (1 to 16)
Time Integral
Set the PID integral for
the outputs.
0 to 9,999 seconds per
repeat
180 sec-
onds
per
repeat
4114
[offset 70]
0x97
(151)
1 to 16
8
59 8006 float
RWES
[``td]
[ td]
Control Loop (1 to 16)
Time Derivative
Set the PID derivative
time for the outputs.
0 to 9,999 seconds 0 seconds 4116
[offset 70]
0x97
(151)
1 to 16
9
60 8007 float
RWES
[``dB]
[ db]
Control Loop (1 to 16)
Dead Band
Set the offset to the
proportional band. With
a negative value, both
heating and cooling out-
puts are active when the
process value is near the
set point. A positive value
keeps heating and cooling
outputs from fighting each
other.
-1,000.0 to 1,000.0°F or
units
-555.556 to 555.556°C
0.0 4118
[offset 70]
0x97
(151)
1 to 16
0xA (10)
61 8008 float
RWES
Note: Some values will be rounded off to fit in the four-character display. Full values
can be read with other interfaces.
If there is only one instance of a menu, no submenus will appear.
R: Read
W: Write
E: EEPROM
S: User Set