User Manual

Watlow EZ-ZONE
®
RME Module • 104 • Chapter 6 Features
Math
Sample and Hold
Range Low
Range High
Pressure Units
Altitude Unit
s
Scale Low
Scale High
Function
Filter
Offset
Filter
Math
Dewpoint
Range Low
Range High
Pressure Units
Altitude Units
Scale Low
Scale High
Function
Filter
Offset
Filter
If E = OFF
, Output Value = Filter [A + Offset]
If E = ON
, Output Value = Filter [last value of A + Offset]
Display units follows Source
A
Output Value = Filter [427.26 * (CP * B / 8.8618)
/ (17.27- (CP * B / 8.8618)) + 32 + Offset]
Source A is used for Calculated Pressure or CP ;
Note: For dewpoint, Source A is temperature (F)
and Source B is RH (%). Saturation pressure
calculation is identical to that used in wet/dry
bulb. Result is in degrees F.
Source Function A
Source Instance A
Source Zone A
Source Error A
Source Function B
Source Instance B
Source Zone B
Source Error B
Source Function C
Source Instance C
Source Zone C
Source Error C
Source Function D
Source Instance D
Source Zone D
Source Error D
Source Function E
Source Instance E
Source Zone E
Source Error E
Source Function A
Source Instance A
Source Zone A
Source Error A
Source Function B
Source Instance B
Source Zone B
Source Error B
Source Function C
Source Instance C
Source Zone C
Source Error C
Source Function D
Source Instance D
Source Zone D
Source Error D
Source Function E
Source Instance E
Source Zone E
Source Error E
Source Value A
Source Value B
Source Value C
Source Value D
Source Value E
Output Value
Error
Source Value A
Source Value B
Source Value C
Source Value D
Source Value E
Output Value
Error
Output Function
This function configures and connects physical outputs to
internal functions.
Note:
Digital Outputs not included on these sheets
An error, when read, can indicate any of the following:
None, Open, Shorted, Measurement Error, Bad Cal Data,
Ambient Error, RTD Error, Fail, Math Error, Not Sourced,
Stale
Output
Overview
Instances - 0 to 22 per RME
Output Value
Error
Output Low Power Scale
Output Time Base
Output Control
Output High
Power Scale
Output Function
Output Function Instance
Output Source Zone
Output Source Error
[``o;u] Output Value : On, Off
[``Fn] Output Function : Off, Analog Input, Alarm, Cool Power,
Heat Power, Compare, Counter, Digital I/O. Profile Event Out A to
H, Function Key, Logic, Linearization, Math, Process Va lue,
Special Function Output 1 to 4, Timer, Variable
[`o;Ct] Output Control : Fixed Time Base, Variable Time Base
[``Fi] Output Function Instance : 1 to 250
[`o;Lo] Output Low Power Scale : 0 to 100 %
[`o;hi] Output High Power Scale : 0 to 100 %
[`o;tb] Output Time Base : 0.1 to 60.0 seconds
[``S2] Output Source Zone : 0 to 16
[otPt] Output Menu
[`SEt] Setup Page
[``Fn] Output Function : Off, Analog Input, Current, Cool Power,
Heat Power, Control Loop Power, Linearization, Math, Process
Value, Set Point Closed, Set Point Open, Special Function Outputs
1 to 4, Variable
[`s;lo] Scale Low: -100.0 to 100.0
[``Fi] Output Function Instance : 1 to 250
[`r;Lo] Range Low: -1,999.000 to 9,999.000°F
[`r;hi] Range High: -1,999.000 to 9,999.000°F
[`s;hi] Scale High: -100.0 to 100.0
[``S2] Output Source Zone : 0 to 16
[`o;Ca] Calibration Offset
[`oty] Output Type: Volts or Milliamps
Output
Off
Output
Digital
Output Low Power Scale
Output Time Base
Output Control
Output High
Power Scale
Output Low Power Scale
Output Time Base
Output Control
Output High Power Scale
Output Function
Output Function Instance
Output Source Zone
Output Source Error
Output Function
Output Function Instance
Output Source Zone
Output Source Error
Output Value
Output Value
Error
Error