User`s manual

NEMA 4X 7
Non-latching Alarm 32, 33, 69
Non-latching Input Error 23, 33, 60
Non-linear output curve 29, 30, 31, 63
Non-volatile memory writes 67
On-Off Control 61, 69
Open Loop 60
Open Loop Output Power 25
Operating Environment 72
Operating Ranges 71
Operations Page 3, 22, 24, 35, 40, 57, 69
Operations Page Overview 22
Operations Parameters Table 35
Operator Interface 71
Ordering Information 73
Output Non-linear Function 1 23, 29, 63
Output Non-linear Function 2 23, 30, 63
Output Non-linear Function 3 23, 31, 63
Output Power Scale High 1 23, 29, 61, 62
Output Power Scale High 2 23, 30, 61, 62
Output Power Scale High 3 23, 31, 61, 62
Output Power Scale Low 1 23, 29, 61, 62
Output Power Scale Low 2 23, 30, 61, 62
Output Power Scale Low 3 23, 31, 61, 62
Output 1 Function 23, 27
Output 1 Process Value 24, 54
Output 1 Type 24, 54
Output 2 Function 23, 30
Output 2 Type 24, 54
Output 3 Function 23, 30
Output 3 Process Value 23, 54
Output 3 Type 24, 54
Output Configuration 60
Output Types 71
Overview 2
Paktron 13
PI Control 62
PID Control 62
Power Limit 1, 2, 3 23, 29, 31, 61, 62
Power Scaling 62
Power specifications 72
Power Supply 18
Power Type 24, 54
Process Alarm 21, 22, 23, 25, 27, 29, 30, 38,
39, 64
Process Decimal Places 23, 26
Process Scale High 23, 27, 60
Process Scale Low 23, 27, 60
Process Value 25
Pre-Run Menu 20, 45, 46
Profile Example 49
Profile Fail 52, 70
Profile Menu 41, 45
Profile Restore 57
Profile Save 57
Profile Select 51
Profile Status Indicator Light 20
Profile Start 23, 34, 51
Profile Status 46, 52
Profile State 51
Profile Type 23, 34, 41, 46, 51
Profiling Menu 41, 45
Profiling Modbus Registers 51, 52, 53
Profiling Page 41
Programming Page Overview 24
Programming Page example 40
Proportional Band Cool 22, 36, 61
Proportional Band Heat 22, 35, 61
Proportional Control 61
Proportional plus Integral (PI) Control 62
Proportional plus Integral plus Derivative
(PID) Control 62
Quencharc 13, 14, 15, 16, 17
Ramp Rate 23, 34, 39, 64
Ramp Rate (profiling) 34, 46, 47, 52
Ramp Scale 23, 34, 64
Ramp and soak Modbus registers 51, 52, 53
Ramp and soak programming page 41
Ramp Target Set Point 25
Ramping 64
Ramping Home Page display 21
Ramping Mode 33, 64
Rate based profile 41, 46, 52
Rate Cool 22, 37, 39, 62
Rate Heat 22, 36, 39, 62
Removal
1/32 DIN 6
1/16 DIN 7
1/8 DIN 8
1/4 DIN 9
Reset Cool 22, 36, 39, 62
Reset Heat 22, 35, 39, 62
Restore Factory Calibration 24, 54, 55, 69
Restore User Profiles 54, 57
Restore User Settings 54, 57
Restoring Factory Calibration 54
Resume 45, 46
Resume a profile 45, 46
Retransmit 29, 30, 31, 32, 65
Right Display 20
Run Menu 34, 45, 46
Running a profile 45, 46
Save User Profiles 24, 54, 57
Save User Settings 24, 54, 57
Saving and Restoring User Profiles 54, 57
Saving and Restoring User Settings 54, 57
Select 45, 46, 51
Sensor Selection 59
Sensor Type 23, 26, 59, 69
Serial Number 1 24, 54
Serial Number 24, 54
Set Point High 23, 27, 59
Set Point High Limit 23, 27, 59
Set Point Low 23, 27, 59
Set Point Low Limit 23, 27, 59
Set Point Low Limit and High Limit 23, 27,
59
Set Point Step 41, 42, 47, 49, 52
Set Value 25
Setting Up a Modbus Network 66
Setup Page 3, 23, 26
Setup Page Overview 23
Soak Step 43, 47, 49, 51
Software Build Number 24, 54
Software ID 24, 54
Software Version 24, 54
Specifications 71
Start File Number 51
Start Step Number 51
Start profile 45
Step 41, 45, 46
Step Number 45, 46, 50, 51, 70
Step Running 52
Step Type 41
Target Set Point 21, 25, 42, 46, 47, 70
Temperature Decimal Places 23, 26
Temperature set point 21, 22
Temperature Units 23, 26, 39
Terminals 72
Thermocouple Linearization 23, 26
Time based profile 34, 41, 42, 51, 52
Time remaining 46
Troubleshooting 68
Two-wire EIA/TIA 485 capability 18
Units of Measurement 23, 33
Units Scale High 23, 27, 60
Units Scale Low 23, 27, 60
Universal Input 71
Up and Down Keys 20
Upper Display 20
Variable Time Base 28, 30, 31, 63
WATCONNECT™ 66
Watlow web site 66
WATVIEW™ 3, 19, 66
Wiring
0 to 10V Î Process Input 12
0 to 20mA Process Input 13
EM Gateway 19
High Voltage AC Power Wiring 11
Low Voltage AC Power Wiring 11
Output 1 Mechanical Relay 13
Output 1 Process 14
Output 1 Solid-state Relay 13
Output 1 Switched DC 14
Output 2 EIA-485 15
Output 2 Mechanical Relay 14
Output 2 Solid-state Relay 15
Output 2 Switched DC 15
Output 3 Mechanical Relay 16
Output 3 Open Collector 17
Output 3 Process 17
Output 3 Solid-state Relay 16
Output 3 Switched DC 16
RTD Input 12
Thermocouple Input 12
Wait-for Process Enable 43, 46, 52
Wait-for Process Value 43, 46, 52, 70
Weight 72
Writing to non-volatile memory 67
Watlow Series SD ■ 75 ■ Appendix