User`s manual

Watlow Series SD ■ 42 ■ Chapter 8 Profiling
Display Parameter Name
Description
Settings Range
(Integer values for Modbus
in parentheses.)
Default Modbus*
(less 40,001
offset)
Read/Write
Appears if:
Note: Some values will be rounded off to fit in the four-character display. Full values can be read with Modbus. All temperature parame-
ters are in °F through Modbus.
* Low register numbers contain the two higher bytes; high register numbers contain the two lower bytes of the four-byte integer. Decimal
precision is implied at three decimal places unless otherwise noted.
[ StYp] Set Point Step
[tg;SP]
[tg.SP}
Target Set Point
Indicates ending set point value the con-
troller ramps to during the set point step.
-1999 to 9999
(-1999000 to 9999000)
Target set point values
must be between [SP;Lo] to
[SP;Hi] or step will fail the
Pre-Run check and will not
run.
75
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
[hour]
[hour}
Hours
The number of hours, (plus Min and Sec
parameters) equal the total step time to
achieve the ending set point under the
[styp] step type.
0 to 99
0
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
Active if the value set
for [ptyp] is [``ti]
or time based profiles.
[Min]
[ Min}
Minutes
The number of minutes, (plus Hour and
Sec parameters) equal the total step time
to achieve the ending set point under the
[styp] step type.
0 to 59
0
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
Active if the value set
for [ptyp] is [``ti]
or time based profiles.
[~SEC]
[ SEC}
Seconds
The number of seconds, (plus Hour and
Min parameters) equal the total step time
to achieve the ending set point under the
[styp] step type.
0 to 59
0
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
Active if the value set
for [ptyp] is [``ti]
or time based profiles.
[rate]
[rAtE}
Rate
Indicates rate at which the set point
changes in degrees per minute.
0 to 9999
100
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
Active if the value set
for [ptyp] is [rate]
or rate based profiles.
[Ent1]
[Ent1}
Event Output 1
Selects whether Event Output 1 is on or
off during the program step.
[`Off] (0)
[``On] (1)
[`Off] (0)
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
Output 1 is set to
[Ent1].
[Ent2]
[Ent2}
Event Output 2
Selects whether Event Output 2 is on or
off during the program step.
[`Off] (0)
[``On] (1)
[`Off] (0)
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
Output 2 is set to
[Ent2].
[Ent3]
[Ent3}
Event Output 3
Selects whether Event Output 3 is on or
off during the program step.
[`Off] (0)
[``On] (1)
[`Off] (0)
See page
53.
Profiling version only.
(SD_ R - _ _ _ _ - _ _ _ _ )
Output 3 is set to
[Ent3].