User`s manual

ManualsBrandsWatlow Electric ManualsNetwork CardRamping and Profiling Microprocessor-Based Control SERIES 1500

Watlow Series SD ■ 39 ■ Chapter 7 Programming

Display Parameter Name

Description

Settings Range

(Integer values for Modbus

in parentheses.)

Default Modbus*

(less 40,001

offset)

Read/Write

Appears if:

Programming Page

The Programming Page allows you to select what parameters appear on the Operations Page. To go to the Pro-

gramming Page, press the Advance ‰ and Infinity ˆ keys for six seconds from the Home Page. {Prog} will appear

in the upper display and {page} in the lower display.

• Press the ‰ Advance Key to move through the parameter prompts.

• Press the Up ¿ or Down ¯ keys to change the parameter value.

• Press the Infinity Key ˆ at any time to return to the Home Page.

[~~P1]

Parameter Location 1

[Po;ht]

(15)

48 R/W

[~~P2]

Parameter Location 2

[`gsd]

(35)

49 R/W

[~~P3]

Parameter Location 3

[`Aut]

(13)

50 R/W

[~~P4]

Parameter Location 4

[~CAL]

(1)

51 R/W

[~~P5]

Parameter Location 5

[ht;m]

(17)

52 R/W

[~~P6]

Parameter Location 6

[pb;ht]

(18)

53 R/W

[~~P7]

Parameter Location 7

[re;ht]

(19)

54 R/W

[~~P8]

Parameter Location 8

[ra;ht]

(20)

55 R/W

[~~P9]

Parameter Location 9

[h;hys]

(22)

56 R/W

[~P10]

Parameter Location 10

[CL;m]

(23)

57 R/W

[~P11]

Parameter Location 11

[pb;cl]

(24)

58 R/W

[~P12]

Parameter Location 12

[re;cL]

(25)

59 R/W

[~P13]

Parameter Location 13

[ra;cl]

(26)

60 R/W

[~P14]

Parameter Location 14

[C;hys]

(28)

61 R/W

[~P15]

Parameter Location 15

[A1;hi]

(4)

62 R/W

[~P16]

Parameter Location 16

[A1;Lo]

(3)

63 R/W

[~P17]

Parameter Location 17

[A2;hi]

(6)

64 R/W

[~P18]

Parameter Location 18

[A2;Lo]

(5)

65 R/W

[~P19]

Parameter Location 19

[A3;hi]

(8)

66 R/W

[~P20]

Parameter Location 20

[A3Loi]

(7)

67 R/W

[~P21]

Parameter Location 21***

[Ent1]

(32)

68 R/W

[~P22]

Parameter Location 22***

[Ent2]

(33)

69 R/W

[~P23]

Parameter Location 23***

[Ent3]

(34)

47 R/W

Note: All parameter locations have the same range of possible values.

** Static set point version only (SD_C-_ _ _ _- _ _ _ _.)

*** Profiling version only (SD_R-_ _ _ _- _ _ _ _.).

All parameter locations

always appear on the

Programming Page.

Static set point version

(SD_ C - _ _ _ _ - _ _ _ _ )

P1 to P20

Profiling version only.

(SD_ R - _ _ _ _ - _ _ _ _ )

P1 to P23

[none] (0) None

[`CAL] (1) Calibration Offset

[`C-F] (2) Temperature Units

(Setup Page)

[A1;Lo] (3) Alarm 1 Low

[A1;hi;] (4) Alarm 1 High

[A2;Lo] (5) Alarm 2 Low

[A2;hi] (6) Alarm 2 High

[A3;;Lo] (7) Alarm 3 Low

[A3;;hi] (8) Alarm 3 High

[hys1] (9) Alarm Hysteresis 1

(Setup Page)

[hys2] (10) Alarm Hysteresis 2

(Setup Page)

[hyS3] (11) Alarm Hysteresis 3

(Setup Page)

[addr] (12) Modbus Device

Address (Setup Page)

[`Aut] (13) Autotune

[A-m] (14) Auto-Manual

[Po;ht] (15) Power Heat

[Po;CL] (16) Power Cool

[ht;M] (17) Heat Control

Method

[Pb;ht] (18) Prop. Band Heat

[It;ht] (19) Integral Heat OR

[re;ht] (19) Reset Heat

[dEht] (20) Derivative Heat OR

[ra;ht] (20) Rate Heat

[db;ht] (21) Dead Band Heat

[h;hys] (22) Heat Hysteresis

[CL;M] (23) Cool Control

Method

[Pb;Cl] (24) Prop. Band Cool

[It;Cl] (25) Integral Cool OR

[rE;Cl] (25) Reset Cool

[dE;Cl] (26) Derivative Cool OR

[ra;Cl] (26) Rate Cool

[db;Cl] (27) Dead Band Cool

[C;hys] (28) Cool Hysteresis

[prop] (29) Proportional Term

[``It] (30) Integral Term

[``dE] (31) Derivative Term

[rP;rt] (32) Ramp Rate (Setup

Page)**

[Ent1] (32) Event Output 1***

[Ent2] (33) Event Output 2***

[Ent3] (34) Event Output 3***

[~gsd] (35) Guaranteed Soak ***