User`s manual

ManualsBrandsWatlow Electric ManualsNetwork CardRamping and Profiling Microprocessor-Based Control SERIES 1500

Watlow Series SD ■ 34 ■ Chapter 5 Setup

Display Parameter Name

Description

Settings Range

(Integer values for Modbus

in parentheses.)

Default Modbus*

(less 40,001

offset)

Read/Write

Appears if:

Note: Some values will be rounded off to fit in the four-character display. Full values can be read with Modbus. All temperature parame-

ters are in °F through Modbus.

* Low numbers contain the two lower bytes; high numbers contain the two higher bytes of the four-byte integer. Decimal precision is im-

plied at three decimal places unless otherwise noted.

** Static set point version only (SD_C-_ _ _ _- _ _ _ _ ).

*** Profiling version only (SD_R-_ _ _ _- _ _ _ _ ).

[Addr]

Modbus Device Address

Set the device address for communica-

tions. Every controller on a network must

have a unique address.

1 to 247 1

This can

only be set

from the

controller

front panel.

Output 2 is a communi-

cations output.

(SD_ _ - _ _ U _ - _ _ _ _ )

[bAud]

Baud Rate

Set the baud rate at which the communi-

cations occurs.

[9600]

[`19;2]

[`38;4]

[9600]

This can

only be set

from the

controller

front panel.

Output 2 is a communi-

cations output.

(SD_ _ - _ _ U _ - _ _ _ _ )

[`LOC]

[ LOC]

Lockout

Set the security level for the user inter-

face.

[```0]

(0) no lockout

*** Full profile access.

[```1]

(1) Set Point,

Auto/Manual, alarms only.

*** Full profile access

[```2]

(2) Set Point,

Auto/Manual, only.

*** Pre-Run and Run Menu

access. only. View a running

profile. Profile editing not

permitted.

[```3]

(3) Set Point only

*** Profile access not per-

mitted.

[```4]

(4) full lockout

*** Profile access not per-

mitted.

See the Features Chapter

for details.

[```0]

(0)

43 R/W

Always active.

[`GSd

[ gSd]

Guaranteed Soak Deviation Value***

Set the value of deviation allowed by the

guaranteed soak deviation function.

1 to 999

(1000 to 999000)

*357, 358

R/W

Profiling version only.

(SD_ R - _ _ _ _ - _ _ _ _ )

[GSdE}

is set to [~YES].

[GS;dE]

[gS.dE]

Guaranteed Soak Deviation Enable***

Enables the guaranteed soak deviation func-

tion in profiles.

[`~no]

Disabled (0)

[~YES]

Enabled (1)

[~~no]

(0)

356 R/W

Profiling version only.

(SD_ R - _ _ _ _ - _ _ _ _ )

[PStr]

Profile Start***

Select where the profile begins the start-

ing set point of the profile, current static

set point or current process temperature.

[`Set]

Static Set Point (0)

[~Pro]

Process (1)

[`Set]

(0)

355 R/W

Profiling version only.

(SD_ R - _ _ _ _ - _ _ _ _ )

[Ptyp]

[PtyP]

Profile Type***

Set the profile ramp to time based or rate

based.

{~~ti] Time based ramp

(0)

{rate] Rate based ramp

(1)

{~~ti] (0)

354 R/W

Profiling version only.

(SD_ R - _ _ _ _ - _ _ _ _ )

[rP;rt]

[rP.rt]

Ramp Rate**

Set the rate for the set point ramp.

0 to 9999

(0000 to 9999000)

100

*268, 269

R/W

[``rP]

is set to

[`Str]

[``On]

Does not appear if

[``rP]

is set to

[`OFF]

[rP;Sc]

[rP.Sc]

Ramp Scale**

Select the scale of the ramp rate.

[hour]

degrees/hour (0)

[Min]

degrees/minute (1)

[hour]

(0)

267 R/W

[``rP]

is set to

[`Str]

[``On]