User`s manual

Watlow Series SD ■ 28 ■ Chapter 5 Setup
Display Parameter Name
Description
Settings Range
(Integer values for Modbus
in parentheses.)
Default Modbus*
(less 40,001
offset)
Read/Write
Appears if:
Note: Some values will be rounded off to fit in the four-character display. Full values can be read with Modbus. All temperature parame-
ters are in °F through Modbus.
* Low register numbers contain the two higher bytes; high register numbers contain the two lower bytes of the four-byte integer. Decimal
precision is implied at three decimal places unless otherwise noted.
*** Profiling version only (SD_R-_ _ _ _- _ _ _ _ ).
[sP;hi]
[SP.hi]
Set Point High Limit
Set the high range for the set point.
[rg;Lo] to max. operating
range (of sensor): if {`sen}
is set to {``tc}
[SP;Lo] +0.100 to 1472: if
{`sen} is set to {`rtd}
[SP;Lo] +0.001 to 9999: if
{`sen} is set to [`MA],
[uolt] or [`Mu].
(Set precision with [P;dEC] ,
Process Decimal Places)
Max. operat-
ing range (J
type): {``tc}
1472: {`rtd]
999: [`MA],
[uolt] and
[`Mu].
*242, 243
R/W (ther-
mocouple)
*246, 247
R/W (RTD)
*250, 251
R/W (mA, V
or mV)
Always active.
[Ftr;E]
[Ftr.E]
Input Filter
Select filtering action.
[`OFF] (0) (no filtering)
[DiSP] (1) (filter only the
display value)
[CntL] (2) (filter the
control input values)
[both] (3)
[`OFF] (0)
89 R/W
Always active.
[FLtr]
[FLtr]
Filter Value
Set the input filter value.
0.0 to 60.0 seconds
(0000 to 60000)
0.0
*87, 88
R/W
[Ftr;E] is not set to
[`OFF] .
[Ot`1]
[Ot 1]
Output 1 Function
Set Output 1 function.
[`OFF] Off (0)
[Pr;AL] Process Alarm (1)
[dE;;AL] Deviation Alarm (2)
[hEAt] Heat Control (3)
[CooL] Cool Control (4)
[E;out] Event (5) ***
[rmt] Retransmit (6)
[hEAt] (3)
143 R/W
Always active.
Active only if Output 1
is a process output (SD_
_ - _ F _ _ - _ _ _ _)
[Ctr1]
[Ctr1]
Control Method 1
Set output 1 control type. This parameter
is only used with PID control, but can be
set anytime.
[`Ftb] Fixed Time Base (0)
[Urtb] Variable Time Base
(1)
[`Ftb] (0)
144 R/W
[Ot`1] is set to [hEAt] or
[CooL] and output type
is SD_ _-_ C _ _-_ _ _ _ or
SD_ _-_ K _ _-_ _ _ _.
[Ftb1]
[Ftb1]
Fixed Time Base 1 (Cycle Time)
Set the time base for Fixed Time Base
Control.
1.0 to 60.0 seconds if Out-
put 1 is a mechanical relay
(1000 to 60000)
0.1 to 60.0 seconds if Out-
put 1 is not a mechanical
relay
(100 to 60000)
20.0: mech.
relay
5.0: solid-
state relay
1.0: switched
dc
*145, 146
R/W
[Ot`1] is set to [hEAt]
or [CooL] , [Ctr1] is set
to [`Ftb] and Output 1
is not a process output.
(not SD_ _ - _ F _ _ -
_ _ _ _ )
[SP;Lo]
[SP.Lo]
Set Point Low Limit
Set the low range for the set point.
Min. operating range (of
sensor) to [SP;Hi] -0.100: if
{`sen} is set to {``tc}
-328 to [SP;hi] -0.100: if
{`sen] is set to {`rtd}
-1999 to [SP;hi] -0.001: if
{`sen} is set to [`MA],
[uolt] or [`Mu].
(Set precision with [P;dEC] ,
Process Decimal Places.)
Min. operat-
ing range (J
type): {``tc}
-328: {`rtd}
-999: [`MA],
[uolt] and
[`Mu].
*240, 241
R/W (ther-
mocouple)
*244, 245
R/W (RTD)
*248, 249
R/W (mA, V
or mV)
Always active.