MINICHEF 2000 TM Applications 1 - 6 Cook-&-Hold Oven Applications Guide Programming & Operating Steps 97 TOTAL CUSTOMER SATISFACTION Watlow Controls 1241 Bundy Blvd. P.O. Box 5580 Winona, Minnesota U.S.A. 55987-5580 (507) 454-5300, Fax (507) 452-4507 WMC2-XAGN-0001-Rev A May 1997 ISO 9001 Registered Company Winona, Minnesota USA $5.00 Made in the U.S.A.
Table of Contents Application 1 Automatic Cook-&-Hold Oven with Meat Probe Option . . . 1 Application 2 Automatic Cook-&-Hold Oven with Meat Probe Optiion . . 11 Application 3 Automatic Cook-&-Hold Oven . . . . . . . . . . . . . . . . . . . 23 Application 4 Automatic Cook-&-Hold Oven . . . . . . . . . . . . . . . . . . . 33 Application 5 Manual Cook-&-Hold Oven with Meat Probe Option . . . . 43 Application 6 Manual Cook-&-Hold Oven. . . . . . . . . . . . . . . . . . . . . 55 Ordering Information . . . . .
1 Application 1 Automatic Cook-&-Hold Oven with Meat Probe Option One Heat Channel, Six Menus Introduction to Application 1 . . . . . . . . . . . . . . . 1 Configuration Mode Quick Reference . . . . . . . . . 3 Program Mode Quick Reference . . . . . . . . . . . . 4 Step 7 Design a Faceplate Overlay. . . . . . . . . . . 5 Step 8 Operate the Controller . . . . . . . . . . . . . .
Key Functions in Configuration Mode MINICHEF 2000 Display five-digit, sevensegment numeric LED display. Indicator lights (1 for each key, 2 for heat channels). G H A Edit key (A) Access the next level of parameters or values. Enter key (B) Enter the value and return to previous level. Home key (D) Move to Operation Mode with a two-second key press. C B Edit Up key (C) Move up the lists. Enter D Home Escape key (E) Return to original value when editing a parameter value.
Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. You must select Application 1 to access them. For directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes an explanation of all parameters and values.
Program Mode Quick Reference These are the functions, parameters and values included in the Program Mode for this application. You must select Application 1 to access them. For menu programming directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes a detailed explanation of all parameters and values. Function Parameter Value [M`__] Menu Numbers 1 - 6 [Stpt1] Set point 1 Temperature of set point 1.
Step 7 Design a Faceplate Overlay To complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide.
Step 8 Operate the Controller Summary of Key Functions in Operation Mode Key Function A Menu 1 B Menu 2 C Menu 3 D Menu 4 E Menu 5 F Menu 6 Startup Apply power to the oven. [`iDle] will appear on the display. If the Real Time Clock Display option is installed and [SetUp] / [Cloc`] = [``yes], the time of day will appear on the display.
When the oven is at operating temperature (set point minus the ready band) [Ready] will appear on the display and the menu key indicator light will flash rapidly. You are now ready to cook with the active menu. • If the oven is at operating temperature, the display goes directly to [Ready] without indicating preheat or temperature. Note: You can skip preheat and go directly to the cooking sequence by pressing the menu key a second time.
switch to the Hold sequence. The display will alternate slowly between Hold and count up time. MINICHEF 2000 [`Ho1d]] [``!¢4] [`Ho1d] [``!¢9] ... G H A B Edit Accept D E Exit Back-Up C F If the Hold time [HtinE] parameter has been set to 0, the unit will count up time indefinitely. The hold sequence will end and the controller will go into idle when you cancel the current menu by pressing the active menu key.
1. With idle on the display, place food in the oven and insert meat probe (if necessary). MINICHEF 2000 MINICHEF 2000 [`idle] G [`0009] H A B Edit Accept D E Exit Back-Up G C F STEADY ON H A B Edit Accept D E Exit Back-Up C F 2. Press the key for the menu you want to run. The menu key indicator will light up. Time will count down on the display. The unit will run the following two-step cooking sequence: Countdown time is displayed.
Pause a Menu While cooking, you can pause cooking time by pressing the active menu key once. The menu key indicator light will flash rapidly. Countdown time will resume when you press the active menu key again. Cancel a Menu Canceling a menu stops controller operation completely. The controller does not maintain set point temperatures or run time. You cancel a menu to run another menu, stop menu operation for any reason, or are preparing to shut off the oven. • Press the active menu key for 2 seconds.
2 Application 2 Automatic Cook-&-Hold Oven with Meat Probe Option One Heat Channel, 17 Menus Introduction to Application 2 . . . . . . . . . . . . . . 11 Configuration Mode Quick Reference . . . . . . . . 13 Program Mode Quick Reference. . . . . . . . . . . . 14 Step 7 Design a Faceplate Overlay . . . . . . . . . . 15 Step 8 Operate the Controller . . . . . . . . . . . . .
Key Functions in Configuration Mode MINICHEF 2000 Display five-digit, sevensegment numeric LED display. Indicator lights (1 for each key, 2 for heat channels). G H A Edit key (A) Access the next level of parameters or values. Enter key (B) Enter the value and return to previous level. Home key (D) Move to Operation Mode with a two-second key press. C B Edit Up key (C) Move up the lists. Enter D Home Escape key (E) Return to original value when editing a parameter value.
Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. You must select Application 2 to access them. For directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes an explanation of all parameters and values.
Program Mode Quick Reference These are the functions, parameters and values included in the Program Mode for this application. You must select Application 2 to access them. For menu programming directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes a detailed explanation of all parameters and values. Function Parameter Value [M``] Menu Numbers 1 - 17 [Stpt1] Set point 1 Temperature of set point 1.
Step 7 Design a Faceplate Overlay To complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide. Suggested End-user Overlay: Your Company Logo Heat 1 2 3 Up 4 Menu Select 5 6 Start/ Stop Down This Prototyping and Training Membrane Overlay will help you with the configuration and programming steps.
Step 8 Operate the Controller Summary of Key Functions in Operation Mode Key Operation Function A None B None C Menu Increment D Menu Select E Start/Stop F Menu Decrement Start-up Apply power to the oven. [`idle] will appear on the display. If the Real Time Clock Display option is installed and [setup] / [Cloc`] = [``Yes], the time of day will appear on the display. Select a Menu 1. Press the Menu Select key The controller will display the currently selected menu.
[`idle] G RAPID FLASH SLOW FLASH MINICHEF 2000 MINICHEF 2000 [pre-`] [`Heat] H A B Edit Accept D E Exit Back-Up MINICHEF 2000 [100f`] G C F [ready] H A B Edit Accept D E Exit Back-Up G C F H A B Edit Accept D E C Exit Back-Up F AT OPERATING TEMPERATURE (PREHEAT CONDITION MET) • Activate the menu by pressing the Start/Stop key. If the oven is not at operating temperature, it will preheat.
3. With [ready] on the display, place the food in the oven and insert the meat probe (if necessary). Then press the Start/Stop key (indicated by the rapidly flashing indicator light). The Start/Stop key indicator will light up. Time will count down on the display. The unit will run the following two-step cooking sequence: Countdown time is displayed. It is the total of the programmed Time 1 plus Time 2. Set point 1 and Fan 1 will run until Time 1 expires. Set point 2 and Fan 2 will run until Time 2 expires.
light will be off. With Sound set to 1, 2, or 3: [``end] will appear on the display and an audible tone will be emitted. The Start/Stop key indicator light will flash rapidly. You can acknowledge and silence the tone by pressing the Start/Stop key or it will automatically time out within 2 seconds for setting 1 or 20 seconds for settings 2 or 3 and then go into idle. The Start/Stop key indicator light will be off.
hold and count up time. If the Hold time parameter [Htine] has been set to 0, the unit will count up time indefinitely. The hold sequence will end when you cancel the current menu or activate another menu. If Hold time [Htine] is greater than 0, the unit will run the hold sequence until the hold time expires. It will then switch to the sequence described in 6. 6.
Change Menus 1. With the controller in idle, select the menu you want to run by performing the procedure under “Select a Menu” earlier in this section. 2. Press the Start/Stop key. Based on its programming, the unit will run the menu in one of the ways described earlier. Door Opening When you open the oven door (uses Event Output 1 for switch closure. Switch closure indicates the door is open) the unit will act as described below.
22 ■ Watlow M I N I C H E F 2000 Application 2
3 Application 3 Automatic Cook-&-Hold Oven One Heat Channel, Six Menus Introduction to Application 3 . . . . . . . . . . . . . . 23 Configuration Mode Quick Reference . . . . . . . . 25 Program Mode Quick Reference . . . . . . . . . . . . 26 Step 7 Design a Faceplate Overlay . . . . . . . . . . 27 Step 8 Operate the Controller . . . . . . . . . . . . .
Key Functions in Configuration Mode MINICHEF 2000 Display five-digit, sevensegment numeric LED display. Indicator lights (1 for each key, 2 for heat channels). G H A Edit key (A) Access the next level of parameters or values. Enter key (B) Enter the value and return to previous level. Home key (D) Move to Operation Mode with a two-second key press. C B Edit Up key (C) Move up the lists. Enter D Home Escape key (E) Return to original value when editing a parameter value.
Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. You must select Application 3 to access them. For directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes an explanation of all parameters and values.
Program Mode Quick Reference These are the functions, parameters and values included in the Program Mode for this application. You must select Application 3 to access them. For menu programming directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes a detailed explanation of all parameters and values. Function Parameter [M`__] Menu Numbers 1 - 6 [Stpt1] Set point 1 Temperature of set point 1. [TiNe1] Time 1 Run time of set point 1.
Step 7 Design a Faceplate Overlay To complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide.
Step 8 Operate the Controller Summary of Key Functions in Operation Mode Key Function A Menu 1 B Menu 2 C Menu 3 D Menu 4 E Menu 5 F Menu 6 Startup Apply power to the oven. [`iDle] will appear on the display. If the Real-time Clock option is installed and [SetUp] / [time] is programmed, the time of day will appear on the display.
When the oven is at operating temperature (above the set point minus the ready band) [Ready] will appear on the display and the menu key indicator light will flash rapidly. You are now ready to cook with the active menu. • If the oven is at operating temperature, the display goes directly to [Ready] without indicating preheat or temperature. Note: You can skip preheat and go directly to the cooking sequence by pressing the menu key a second time.
If the Hold time parameter [Htine] has been set to 0, the unit will count up time indefinitely. The hold sequence will end and the controller will go into idle when you cancel the current menu by pressing the active menu key. If [Htine] is greater than 0, the unit will run the hold sequence until the hold time expires. It will then switch to the sequence described in 4. 4.
2. Press the key for the menu you want to run. The menu key indicator will light up. Time will count down on the display. The unit will run the following two-step cooking sequence: Countdown time is displayed. It is the total of the programmed Time 1 plus Time 2. Set point 1 and Fan 1 will run until Time 1 expires. Set point 2 and Fan 2 will run until Time 2 expires. You will not see the switch-over from Time 1 to Time 2. 3.
Cancel a Menu Canceling a menu stops controller operation completely. The controller does not maintain set point temperatures or run time. You cancel a menu to run another menu, stop menu operation for any reason, or are preparing to shut off the oven. • Press the active menu key for 2 seconds (in hold, momentarily press the menu key). Heat outputs will switch off. Heat output indicator lights will switch off. [`idle] or time of day will be on the display. Change Menus or Restart 1.
4 Application 4 Automatic Cook-&-Hold Oven One Heat Channel, 20 Menus Introduction to Application 4 . . . . . . . . . . . . . . 33 Configuration Mode Quick Reference . . . . . . . . 35 Program Mode Quick Reference . . . . . . . . . . . . 36 Step 7 Design a Faceplate Overlay . . . . . . . . . . 37 Step 8 Operate the Controller . . . . . . . . . . . . . 38 Application 4 allows you to program as many as twenty menus to control one temperature channel, a fan and cooking time for an automatic cook-&-hold oven.
Key Functions in Configuration Mode MINICHEF 2000 Display five-digit, sevensegment numeric LED display. Indicator lights (1 for each key, 2 for heat channels). G H A Edit key (A) Access the next level of parameters or values. Enter key (B) Enter the value and return to previous level. Home key (D) Move to Operation Mode with a two-second key press. C B Edit Up key (C) Move up the lists. Enter D Home Escape key (E) Return to original value when editing a parameter value.
Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. You must select Application 4 to access them. For directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes an explanation of all parameters and values.
Program Mode Quick Reference These are the functions, parameters and values included in the Program Mode for this application. You must select Application 4 to access them. For menu programming directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes a detailed explanation of all parameters and values. Function Parameter [M`__] Menu Numbers 1 - 20 [Stpt1] Set point 1 Temperature of set point 1. [TiNe1] Time 1 Run time of set point 1.
Step 7 Design a Faceplate Overlay To complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide. Suggested End-user Overlay: Your Company Logo Heat 1 2 3 Up 4 Menu Select 5 6 Start/ Stop Down This Prototyping and Training Membrane Overlay will help you with the configuration and programming steps.
Step 8 Operate the Controller Summary of Key Functions in Operation Mode Key Function A None B None C Menu Increment D Menu Select E Start/Stop F Menu Decrement Start-up Apply power to the oven. [`idle] will appear on the display. If the Real-time Clock option is installed and [setUp] / [time] is programmed, the time of day will appear on the display. Select a Menu 1.
Preheat If the [Ready] parameter under the [SEtUP] function in the Configuration Mode is set to yes, the controller will detect temperatures and preheat to operating temperature (above the relative set point minus the ready band) as required. • Activate the menu by pressing the Start/Stop key.
3. With [ready] on the display, place the food in the oven. Then press the Start/Stop key (indicated by the rapidly flashing indicator light). The Start/Stop key indicator will light up. Time will count down on the display. The unit will run the following two-step cooking sequence: Countdown time is displayed. It is the total of the programmed Time 1 plus Time 2. Set point 1 and Fan 1 will run until Time 1 expires. Set point 2 and Fan 2 will run until Time 2 expires.
Setpoint 1 and Fan 1 will run until Time 1 expires. Setpoint 2 and Fan 2 will run until Time 2 expires. You will not see the switch-over from Time 1 to Time 2. 4. Once the cooking sequence is complete, the unit will switch to the Hold sequence. The display will alternate slowly between [`Ho1d] and count up time. If the Hold time parameter [Htine] has been set to 0, the unit will count up time indefinitely.
Door Opening When you open the oven door (uses Event Output 1 for switch closure. Switch closure indicates the door is open) the unit will act as described below. During the cooking sequence: time is paused and [`door] will appear on the display. The heat and fan output signal will shut off. During the preheat or hold sequence: [`door] will appear on the display. The heat and fan output signals will be shut off. When you close the door the unit will operate normally.
5 Application 5 Manual Cook-&-Hold Oven with Meat Probe Option One Heat Channel Introduction to Application 5 . . . . . . . . . . . . . . 43 Configuration Mode Quick Reference . . . . . . . . 45 Step 7 Design a Faceplate Overlay . . . . . . . . . . 47 Step 8 Operate the Controller . . . . . . . . . . . . . 48 Application 5 allows the manual setting of a single menu to control a temperature channel, and cooking time for a manual cook-&-hold oven with a meat probe.
Key Functions in Configuration Mode MINICHEF 2000 Display five-digit, sevensegment numeric LED display. Indicator lights (1 for each key, 2 for heat channels). G H A Edit key (A) Access the next level of parameters or values. Edit Enter key (B) Enter the value and return to previous level. Up key (C) Move up the lists. Enter D Home key (D) Move to Operation Mode with a two-second key press. C B Home Escape key (E) Return to original value when editing a parameter value.
Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. You must select Application 5 to access them. For directions, see the Hardware & Software Setup Guide. The Appendix of that guide includes an explanation of all parameters and values.
Auto-tuning Note: Before auto-tuning Application 5, [teNp1] in the operations menu must first be set to a value that is typical of your application. (See the Hardware & Software Setup Guide for information) Then set [tHerl] / [tunE1] to [```on]. After you accept [```on], by pressing “Enter,” the controller will display [`tunE] while auto-tuning is taking place. The controller will cancel the auto-tuning process if it cannot be completed in 80 minutes.
Step 7 Design a Faceplate Overlay To complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide.
Step 8 Operate the Controller Summary of Key Functions in Operation Mode Key Operation Function A Cook Temp(s) B Cook Time(s) C Up (Increment) D Hold Temp E Start/Stop F Down (Decrement) Start-up Apply power to the oven. [`idle] will appear on the display. If the Real Time Clock option is installed and [Setup] / [Cloc`] = [``yes], the time of day will appear on the display.
4. Press the Up-arrow or Down-arrow key until the value you want appears on the display. 5. Press the Cook Temp key again. The probe temperature has been set. [`idle] will appear on the display. MINICHEF 2000 MINICHEF 2000 [600`F] G [`iDLE] H A B Edit Accept D E Exit Back-Up G C F H A B Edit Accept D E Exit Back-Up C F Set the cooking time: 1. Press the Cook Time key. [TiNe1] and then the cooking time value will appear on the display. 2.
2. Press the Up-arrow or Down-arrow key until the value you want appears on the display. 3. Press the Cook Temp key again. The first cooking temperature has been set. [tENP2] and then the second cooking temperature value will appear on the display. 4. Press the Up-arrow or Down-arrow key until the value you want appears on the display. 5. Press the Cook Temp key again. The second cooking temperature has been set. [PtENP] and then the probe temperature value will appear on the display. 6.
Five Second Timeout When using the up or down keys to change a value, if you do not press any key for 5 seconds, the controller will automatically be set to the last value on the display and return to [`idle]. Preheat If the [ready] parameter under the [SEtUP] function in the Configuration Mode is set to yes, when you press the Start/Stop key to activate the menu, the controller will detect temperatures and preheat to operating temperature (above relative set point minus the ready band) as required.
If the preheat condition has not been met, the oven will preheat until [ready] appears on the display. Note: You can skip preheat and go directly to the cooking sequence by pressing the Start/Stop key a second time. If the oven is already at operating temperature [ready] will appear on the display. 3. With [ready] on the display, place the food in the oven and insert the meat probe. Then press the Start/Stop key (indicated by the rapidly flashing indicator light). The Start/Stop key indicator will light up.
Depending on the way the controller was programmed at [Etype] / [Steps] the menu will run in one step or two. One Step Countdown time is displayed. Set point 1 will run until time expires. Two Step Countdown time is displayed. It is the total of the programmed Time 1 plus Time 2. Set point 1 will run until Time 1 expires. Set point 2 will run until Time 2 expires. You will not see the switch-over from Time 1 to Time 2. 4. When the timed cooking sequence is complete, the oven will run the probe sequence.
Cancel a Menu Canceling a menu stops the controller completely. The controller does not maintain set point temperatures or run time. You cancel a menu to change the menu, stop menu operation for any reason, or are preparing to shut off the oven. Press the Start/Stop key for 2 seconds (in hold, momentarily press the Start/Stop key). Heat outputs will switch off. Heat output indicator lights will switch off. [`idLE] or time of day will be on the display. Restart a Menu 1.
6 Application 6 Manual Cook & Hold Oven One Heat Channel, One Manual Menu Introduction to Application 6 . . . . . . . . . . . . . . 55 Configuration Mode Quick Reference . . . . . . . . 57 Step 7 Design a Faceplate Overlay . . . . . . . . . . 59 Step 8 Operate the Controller . . . . . . . . . . . . . 60 Application 6 allows the manual setting of a single menu to control a temperature channel, and cooking time for a manual cook-&-hold oven.
Key Functions in Configuration Mode MINICHEF 2000 Display five-digit, sevensegment numeric LED display. Indicator lights (1 for each key, 2 for heat channels). G H A Edit key (A) Access the next level of parameters or values. Edit Enter key (B) Enter the value and return to previous level. Up key (C) Move up the lists. Enter D Home key (D) Move to Operation Mode with a two-second key press. C B Home Escape key (E) Return to original value when editing a parameter value.
Configuration Mode Quick Reference These are the functions, parameters and values included in the Configuration Mode for this application. You must select Application 6 to access them. For directions, see the Hardware & Software Setup Guide.
Auto-tuning Note: Before auto-tuning Application 6, [teNp1] in the operations menu must first be set to a value that is typical of your application. (See Hardware & Software Setup Guide for information on programming menus.) Then set [tHerl] / [tunE1] to [```on]. After you accept [```on], by pressing “Enter,” the controller will display [`tunE] while auto-tuning is taking place. The controller will cancel the auto-tuning process if it cannot be completed in 80 minutes.
Step 7 Design a Faceplate Overlay To complete the installation, you must apply a graphic membrane to the front panel of the controller. The following artwork will help you design and create a membrane for this application. For more dimensions and guidelines, see the Hardware & Software Setup Guide.
Step 8 Operate the Controller Summary of Key Functions in Operation Mode Key Operation Function A Cook Temp(s) B Cook Time(s) C Up (Increment) D Hold Temp E Start/Stop F Down (Decrement) Start-up Apply power to the oven. [`idle] will appear on the display. If the Real Time Clock option is installed and [SetUp] / [time] is programmed, the time of day will appear on the display.
Set the cooking time. 1. Press the Cook Time key [tiNE1] and then the cooking time value will appear on the display. 2. Press the Up-arrow or Down-arrow key until the value you want appears on the display. 3. Press the Cook Time key again. The cooking time has been set. [`idle] will appear on the display. Set the Hold Temperature. 1. Press the Hold Temp key [HteNp] and then the hold temperature value will appear on the display. 2.
Set the two cooking times. 1. Press the Cook Time key [TiNe1] and then the first cooking time value will appear on the display. 2. Press the Up-arrow or Down-arrow key until the value you want appears on the display. 3. Press the Cook Time key again. The first cooking time has been set. [tiNE2] and then the second cooking time value will appear on the display. 4. Press the Up-arrow or Down-arrow key until the value you want appears on the display. 5. Press the Cook Time key again.
• The heat output indicator light - G, just below the display- will light up whenever the controller is calling for heat. When the oven is at operating temperature (above the relative set point minus the ready band) [ready] will appear on the display and the Start/Stop key indicator light will flash rapidly. You are now ready to cook with the active menu. If the oven is at operating temperature, the display goes directly to [ready] without indicating preheat or temperature.
The unit will count up time indefinitely. The hold sequence will end and the controller will go into idle when you cancel the current menu by pressing the Start/Stop key. 5. Once the controller goes into idle, the Start/Stop key indicator light will switch off. 6. To repeat cooking, repeat steps 1 through 4.
the cooking sequence. Temperature changes made while cooking are saved and become part of the permanent menu. Time changes are not saved and do not become part of the permanent menu. Pause a Menu While cooking, you can pause cooking time by pressing the Start/Stop key once. The Start/Stop key indicator light will flash rapidly [PAUSE] will appear on the display. Countdown time will resume when you press the active menu key again. Cancel a Menu Canceling a menu stops the controller completely.
Specifications (1032) Control Mode 1 • Single and dual heat channels, PID or on/off. • Microprocessor-based, programmable, reverse-acting control outputs. • User-selectable embedded application software defines operation of display, keys, inputs, outputs, timing action. • One-step auto-tuning, WatHelp diagnostics, WatCurve temperature compensation.
Ordering Information (1033) F 2 HA- _ _ _ 1 - _ _AA MINICHEF™ 2000 Cooking controller with numerous food equipment application software sets, single and dual channel on/off or PID temperature regulation, timer and machine-function control, microprocessorbased, programmable, auto-tuning, WatCurve, WatHelp diagnostics, 24VÅ (ac) power input, agency approved, flush mounted (membrane faceplate supplied by customer).
Ordering Information: Part Numbers & Accessories MINICHEF 2000 Accessories MINICHEF 2000 Documentation 0836-0442-0000 WMC2-XUGN-0000 A001-0298-0000 0238-0679-0000 0830-0479-0000 A001-0249-0001 A001-0249-0002 Sensor Input Mating Connector, (RIACON #31007106), 6-position, quick-connect terminal, screw connection for 28-14 AWG wires, tighten to 7 in/lb Power Supply and I / O Mating Connector Kit.
Watlow Controls Watlow Controls is a division of Watlow Electric Mfg. Co., St. Louis, Missouri, a manufacturer of industrial electric heating products since 1922. Watlow begins with a full set of specifications and completes an industrial product that is manufactured totally inhouse, in the U.S.A. Watlow products include electric heaters, sensors, controls and switching devices.
Watlow MINICHEF™ 2000 Cook-&-Hold Oven Applications Guide Watlow Controls, 1241 Bundy Blvd., P.O. Box 5580, Winona, MN U.S.A.
Ordering Information (1033) F2HA-___1-__AA MINICHEF 2000™ Cooking controller with numerous food equipment application software sets, single and dual channel on/off or PID temperature regulation, timer and machine-function control, microprocessorbased, programmable, auto-tuning, WatCurve, WatHelp diagnostics, 24VÅ (ac) power input, agency approved, flush mounted (membrane faceplate supplied by customer).
the display. (The message, which varies based on programming at [M```] / [ALArn] will appear for ten seconds.) An audible tone will sound for five seconds. Time will continue to count down on the display. 4. When the cooking cycle is finished one of the following will happen, depending on the way the controller was programmed at [EtypE] / {Sound]. With Sound set to 0: The controller automatically switches to idle, where the controller maintains the temperatures at set point and does not run time.
Watlow MINICHEF™ 2000 Cook-&-Hold Oven Applications Guide Watlow Controls, 1241 Bundy Blvd., P.O. Box 5580, Winona, MN U.S.A.
