User`s manual

ManualsBrandsWatlow Electric ManualsComputer equipmentIntegrated Controller Rev C EZ-ZONE PM

Watlow EZ-ZONE

®

ST • 60 • Chapter 6 Factor y Page

Control Module • Factory Page

Display

Parameter Name

Description

Range Default

Modbus

Relative Ad-

dress

CIP

Class

Instance

Attribute

hex (dec)

Pro DP

Index

Par

ID

RUI/

GTW

Mod-

bus

Data

Type

&

Read/

Write

[CUSt]

[FCty]

Custom Setup Menu

[`par]

[ Par]

Custom

Parameter 1 to 20

Select the parameters

that will appear in the

Home Page.

The Parameter 1 value

will appear in the

upper display of the

Home Page. It cannot

be changed with the

Up and Down Keys

in the Home Page.

The Parameter 2 value

will appear in the

lower display in the

Home Page. It can

be changed with the

Up and Down Keys,

if the parameter is a

writable one.

Scroll through the

other Home Page

parameters with the

Advance Key

‰

.

[nonE] None (61)

[`l;st] Limit Status (1668)

[`L;hy] Limit Hysteresis (183)

[`Lh;S] Limit High Set Point (182)

[`LL;S] Limit Low Set Point (181)

[`CU;r] Sensed Current (179)

[gSd1] Guaranteed Soak Deviation

1 Value (1214)

[P;ACr] Profile Action Request (109)

[P;Str] Profile Start (79)

[idLE] Idle Set Point (107)

[t;tUn] TRU-TUNE+

®

Enable (205)

[`r;rt] Ramp Rate (177)

[`C;hy] Cool Hysteresis (170)

[`C;Pb] Cool Proportional Band

(169)

[`h;hy] Heat Hysteresis (167)

[`h;Pb] Heat Proportional Band

(166)

[``db] Dead Band (164)

[``td] Time Derivative (163)

[``ti] Time Integral (162)

[`C;Pr] Cool Power (161)

[`h;Pr] Heat Power (160)

[`C;M] User Control Mode (159)

[`AUt] Autotune (158)

[``op] Open Loop Set Point (110)

[AC;SP] Active Set Point (72)

[AC;pu] Active Process Value (25)

[StPt] Set Point (85)

CUSt] Custom Menu (180)

[`A;hy] Alarm Hysteresis (97)

[`A;hi] Alarm High Set Point (78)

[`A;Lo] Alarm Low Set Point (42)

[USr;r] User Restore Set (1171)

[`C_F] Display Units (156)

[`i;CA] Input Calibration Offset

(154)

[`Pro] Process (75)

See:

Home

Page

Instance 1

Map 1 Map 2

- - - - - - - -

- - - - 14005

uint

RWES

[`iid]

[ iid]

Custom (1 to 20)

Instance ID

Select the parameters

that will appear in the

Home Page.

1 to 2 - - - -

Instance 1

Map 1 Map 2

- - - - - - - -

- - - -

- - - - 14003

uint

RWES

[`LoC]

[FCty]

Security Setting Menu

[LoC;o]

[LoC.o]

Security Setting

Operations Page

Change the security

level of the Opera-

tions Page.

1 to 3 2

Instance 1

Map 1 Map 2

- - - - 1692

- - - - - - - - 3002 - - - -

uint

RWE

Note:

Some values will be rounded off to fit in the four-character display. Full values can be

read with another interface.

If there is only one instance of a menu, no submenus will appear.

R: Read

W: Write

E: EE-

PROM

S: User

Set