User`s manual

ManualsBrandsWatlow Electric ManualsComputer equipmentIntegrated Controller Rev C EZ-ZONE PM

Watlow EZ-ZONE

ST • 40 • Chapter 4 Setup Page

Setup Page

Display

Parameter Name

Description

Range Default

Modbus

Relative

Address

CIP

Class

Instance

Attribute

hex (dec)

Pro DP

Index

Par

RUI/

GTW

Mod-

bus

Data

Type

Read/

Write

[``Ai]

[`Set]

Analog Input Menu

[`Sen]

[ SEn]

Analog Input (1 to 2)

Sensor Type

Set the analog sensor type

to match the device wired

to this input.

Note:

There is no open-

sensor detection

for process inputs.

[`oFF] Off (62)

[``tC] Thermocouple (95)

[`mu] Millivolts (56)

[uolT] Volts dc (104)

[`MA]

Milliamps dc (112)

[r0;1H] RTD 100 Ω (113)

[r1;0H] RTD 1,000 Ω (114)

Instance 1

Map 1 Map 2

42 368

Instance 2

Map 1 Map 2

70 458

0x68 (104)

1 to 2

3 4005 Inst. 1

368

Inst. 2

528

uint

RWES

[`Lin]

[ Lin]

Analog Input (1 to 2)

Linearization

Set the linearization to

match the thermocouple

wired to this input.

[```J] J (46)

[```F] F (30)

[```E] E (26)

[```d] D (23)

[```C] C (15)

[```b] B (11)

[```t] T (93)

[```S] S (84)

[```r] R (80)

[```n] N (58)

[```H] K (48)

Instance 1

Map 1 Map 2

43 370

Instance 2

Map 1 Map 2

71 460

0x68 (104)

1 to 2

4 4006 Inst. 1

370

Inst. 2

530

uint

RWES

[`Rt;L]

[ rt.L]

Analog Input (1 to 2)

RTD Leads

Set to match the number

of leads on the RTD wired

to this input.

[```2] 2 (1)

[```3] 3 (2)

2 Instance 1

Map 1 Map 2

44 372

Instance 2

Map 1 Map 2

72 462

0x68 (104)

1 to 2

- - - - 4007 Inst. 1

372

Inst. 2

532

uint

RWES

[Unit]

[Unit]

Analog Input (1 to 2)

Units

Set the type of units the

sensor will measure.

[`A;tP] Absolute Temperature

(1540)

[``rh] Relative Humidity

(1538)

[`Pro] Process (75)

[PWr] Power (73)

Process Instance 1

Map 1 Map 2

- - - - 442

Instance 2

Map 1 Map 2

- - - - 532

0x68 (104)

1 to 2

0x2A (42)

5 4042 - - - - uint

RWES

Note:

Some values will be rounded off to fit in the four-character display.

Full values can be read with other interfaces.

If there is only one instance of a menu, no submenus will appear.

R: Read

W: Write

E: EE-

PROM

S: User

Set

To go to the Setup Page from the Home Page, press both

the Up ¿ and Down ¯ keys for six seconds. [``Ai] will

appear in the upper display and [`Set] will appear in

the lower display.

• Press the Up ¿ or Down ¯ key to move through

the menus.

• Press the Advance Key

‰

to move to a submenu.

• Press the Up ¿ or Down ¯ key to move through

the submenus.

• Press the Advance Key

‰

to move through the pa-

rameters of the menu or submenu.

• Press the Infinity Key ˆ to move backwards

through the levels: parameter to submenu; sub-

menu to menu; menu to Home Page.

• Press and hold the Infinity Key ˆ for two seconds

to return to the Home Page.

Note:

Avoid continuous writes within loops. Excessive writes to EEPROM

will cause premature EEPROM failure. The EEPROM is rated for

1,000,000 writes. Navigate to Setup Page under the CoM menu and

set prompt Non-volatile Save [`nU;S] to No.