2 OPERATING MANUAL GSM2109 and GSM1009-1SFP Switch Managed Switch with Eight 10/100/1000Base-TX Ports Plus One Mini GBIC slot for 1000Base-SX or LX fiber or one 10/100/1000Base-TX port CORPORATE HEADQUATERS MANUFACTURING/CUSTOMER SERVICE 5001 American Blvd. W., Suite 605 945 37 Avenue, NW Bloomington, MN 55437 Rochester, MN 55901 Phone: 800.441.5319 Phone: 800.328.2275 Phone: 952.831.5603 Phone: 507.252.1951 Fax: 952.831.5605 th Fax: 507.285.1952 Web site: http://www.watersnet.
Table of Contents 1.0 Specifications ...................................................................................................5 2.0 Package Contents.............................................................................................8 3.0 Introduction.......................................................................................................8 3.1 Hardware Features..............................................................................................9 3.
5.8 Backup Configuration ........................................................................................48 5.9 System Event Log .............................................................................................48 5.10 SMTP Configuration ..........................................................................................49 5.11 Event Configuration ...........................................................................................50 5.12 SNTP.........................
5.30 Security Menu..................................................................................................81 5.30.1 802.1X Radius...................................................................................................81 5.30.2 MAC Address Table ........................................................................................84 5.31 Factory Default Settings .................................................................................... 87 5.32 Save Configuration.......
1.0 Specifications OPERATIONAL CHARACTERISTICS: MAC Address Table: Switching Mode: Bandwidth: System Throughput: Memory Buffer Size: Performance: 8k Store-and-forward Up to 18Gbps Up to 26.
IEEE 802.1w IEEE 802.1d IEEE 802.1p IEEE 802.1q IEEE 802.
PHYSICAL CHARACTERISTICS: Dimensions: 8.5 x 5.5 x 1.75 in (216 x 140 x 45mm) Weight: 2 lbs (.91kg) GSM1009-1SFP: Dimensions: 11 x 10.5 x 2 in (279 x 267 x 51mm) Weight: 3.7lbs (1.
2.0 Package Contents Examine the shipping container for obvious damage prior to installing this product. Notify the carrier of any damage that you believe occurred during shipment. Ensure that the items listed below are included. If an item is missing, please contact your supplier. Both the GSM2109 and GSM1009-1SFP switch package contains the following: GSM Switch Power Cord Four Rubber Feet RS-232 cable User’s Guide 3.
The switch will automatically detect the speed of connected devices to accommodate 10, 100, 1000Mbps on the RJ45 ports. All RJ45 ports support the Auto MDI/MDIX function. With the built-in Web-based management functionality, managing and configuring the switch is easy. From cabinet management to port-level control and monitoring, you can visually configure and manage your network via your Web Browser.
Automatic MDI/MDIX crossover for each 10/100Base-TX port Console port on front side for system configuration Half-duplex mode for backpressure Full-duplex for flow control Store-and-forward switching architecture Automatic address learning, address migration 8K-entry MAC address table 18Gbps switch fabric 26.7Mbps throughput Broadcast storm filter Web/SNMP/Telnet/CLI/RMON Performs non-blocking full wire speed 3.
VLAN Port based VLAN Double Tag VLAN for management IEEE802.1Q Tag VLAN. Static VLAN groups up to 256 Dynamic VLAN groups up to 2048 VLAN ID can be assigned from 1 to 4094. GVRP function supports 256 groups. Quality of Port based, Tag based, Ipv4 Type of service, Ipv4/Ipv6 service Different service. IGMP Port Security Port Mirror IGMP v1 and v2 compliance and also supports 256 IGMP groups and support query mode. It supports ingress and egress MAC address filter and static source MAC address lock.
DHCP Client, DHCP relay and DHCP Server. DHCP DHCP server provides port based and system based IP pool. Packet filter System log Broadcast storm packet filter by 5%, 10%, 15% and 25%. Provide 1000 log entries and supports remote storage function. Supports DNS client function. DNS Supports RFC2030 Simple Network Time Protocol and up to 5 SNTP NTP servers. 6 mail accounts.
3.3.2 Web-based Management The switch provides an embedded HTML web site residing in flash memory. It offers advanced management features and allow users to manage the switch from anywhere on the network through a standard browser such as Microsoft Internet Explorer. 3.3.3 SNMP Network Management SNMP (Simple Network Management Protocol) provides a means to monitor and control network devices, manage configurations, collect statistics, performance and security information. 3.
Hardware Ports One slot for mini GBIC Nine 10/100/1000 auto MDI/MDIX 10/100Base-TX connections. MDI allows you to connect to another hub or switch and MDIX allows you to connect to a workstation or PC. Therefore, Auto MDI/MDIX means that you can connect to another switch or workstation without a crossover cable. 3.5 LED Indicators The following table provides the status and description of the LEDs. The LEDs provide a real-time indication of systematic operation status.
3.6.1 Attaching Rubber Feet 1. Make sure the mounting surface on the bottom of the switch is free of grease and dust. 2. Remove adhesive backing from the rubber feet. 3. Apply the rubber feet to each corner on the bottom of the switch. 3.6.2 Power On Connect the power cord to the AC power socket on the rear panel of the switch. Check the power indicator on the front panel to see if power is properly supplied. 4.
switch via a direct connection to the RS-232 console port. This port is a female DB-9 connector. You will have access to all of the management functions of the switch from the console connection. Connecting a Terminal or PC to the Console Port Use the supplied RS-232 cable to connect a terminal or PC to the console port. The terminal or PC to be connected must support the terminal emulation program.
1. Press Enter once you have entered the parameters listed above. 2. Turn on the switch. The switch will display a series of messages as it performs a self test. Once the self test is completed, the login screen will be displayed. 3. Enter the username and password. 4. The default user name is root, and the default password is root. You may change the login identification to make it more secure for your network. Figure 4.
5. Once you have logged into the system, the following command prompt will be displayed. Enter enable to access CLI commands. Figure 4.3 – CLI and Telnet Command Prompt Switch management can be accessed via the following methods: • Console Connection described above. Begin entering CLI commands at this prompt. • Telnet – use the default IP of the switch 192.168.16.1 to access switch management via Telnet. • Note: Web Interface described in Section 5.0.
4.2 CLI Commands To use the CLI commands, enter enable once you have logged into the switch. The following table lists the Command level of the CLI commands. Command Description User EXEC This command is a subset of switch> the commands available at the privileged level. Use this command to: Privileged EXEC Prompt Exit Method Logout or quit Enter the enable command while in EXEC mode.
f)# command (with a specific interface) while in the global configuration mode Commands Set List – Used in Next Table User EXEC E Privileged P EXEC Global G configuration VLAN V database Interface I Configuration Waters Network Systems GSM2109/GSM1009-SFP User’s Manual Page 20
The following table lists the System Commands.
Command reload Level G Description Example Halt and perform a cold restart switch(config)#reload default G Restore to default settings switch(config)#default admin username G Changes a login username.
Command Level Description Example fastEthernet 2 show dhcpserver configuration show dhcpserver clients show dhcpserver ip-binding no dhcpserver P Displays configuration of DHCP server switch(config-if)# dhcpserver ipbinding 192.168.1.
The following table lists the Port Commands. Command interface fastEthernet [portid} duplex [full | half] speed [10|100|1000| auto] flowcontrol mode [symmetric| asymmetric] no flowcontrol Level G Description Choose the port for modification Example switch(config)#interface fastEthernet 2 I Use the duplex command to specify the duplex mode for the Fast Ethernet ports Use the speed configuration command to specify the speed mode for operation of the Fast Ethernet ports.
Command Level broadcast-only bandwidth in [value] I bandwidth out I show bandwidth I state [enable | disable] I show interface configuration I show interface status I show interface accounting I no accounting I Waters Network Systems Description broadcast frame” Example switch(config-if)#bandwidth type broadcast-only Set interface input bandwidth. switch(config)#interface Rate range is from 100kbps to fastEthernet 2 102400kbps or to 256000 switch(config-if)#bandwidth kbps for Giga ports.
The following table lists the Trunk Commands.
The following table lists the VLAN Commands. Command vlan database vlanmode Level P V Description Enter VLAN configure mode Used to set VLAN mode. [portbase| 802.1q | gvrp] no vlan V Used to disable VLAN Port based VLAN configuration vlan V Add new port to port-based port-based VLAN grpname [Group Name] grpid [GroupID] port [PortNumbers] show vlan V Displays VLAN information [GroupID] or show vlan no vlan group V Delete port-based group ID [GroupID] IEEE 802.
Command trunk-link tag [TaggedVID List] vlan 8021q port [PortNumber] hybrid-link untag [UntaggedVID] tag [TaggedVID List] vlan 8021q trunk [PortNumber] access-link untag [UntaggedVID] vlan 8021q trunk [PortNumber] trunk-link tag [TaggedVID List] vlan 8021q trunk [PortNumber] hybrid-link untag [UntaggedVID] tag [TaggedVID List] show vlan [GroupID] or show vlan no vlan group [GroupID] Level Description can’t be applied.
The following table lists the Spanning Tree Commands. Command spanning-tree enable spanning-tree priority [0~61440] spanning-tree max-age [seconds] Level G Description Enable spanning tree G Configure spanning tree priority parameter G spanning-tree hello-time [seconds] G spanning-tree forward-time [seconds] G stp-path-cost [1~200000000] I Use the spanning-tree max-age global configuration command to change the interval between messages the spanning tree receives from the root switch.
Command Level stp-path- priority [Port Priority] I stp-admin-p2p [Auto|True| False] I Description In the event of a loop, spanning tree considers the path cost when selecting an interface to place into the forwarding state. Use the spanning-tree port-priority interface configuration command to configure a port priority that is used when two switches tie for position as the root switch. Admin P2P of STP priority. stp-admin-edge [True|False] I Admin Edge of STP priority.
The following table lists the QoS Commands.
The following table lists the IGMP Commands. Command igmp enable Level G Igmp-query auto Igmp-query force show igmp configuration show igmp multi no igmp G no igmp-query G G P P G Description Enables IGMP snooping function Set IGMP query to auto mode Set IGMP query to force mode Displays the details of the IGMP configuration. Displays the details of the IGMP snooping entries.
Command no macaddress-table filter hwaddr [MAC] no macaddress-table Level G Description Remove filter entry of MAC address table Example switch(config)#no mac-address-table filter hwaddr 000012348678 G Remove dynamic entry of MAC address table switch(config)#no mac-address-table The following table lists SNMP Commands.
Command Name ] snmpv3 user [User Name] group [Group Name] password [Authentication Password] [Privacy Password] snmpv3 access context-name [Context Name ] group [Group Name ] security-level [NoAuthNoPriv| AuthNoPriv| AuthPriv] match-rule [Exact|Prifix] views [Read View Name] [Write View Name] [Notify View Name] snmpv3 mibview view [View Name] type [Excluded| Included] sub-oid [OID] show snmp no snmp communitystrings [Community] Level Description Example G Configure the user profile for SNMPV3 agent.
Command no snmp-server host [Host-address] no snmp-server host [Host-address] no snmpv3 user [User Name] no snmpv3 access context-name [Context Name ] group [Group Name ] security-level [NoAuthNo Priv|AuthNoPriv |AuthPriv] match-rule [Exact|Prifix] views [Read View Name] [Write View Name] [Notify View Name] no snmpv3 mibview view [View Name] type [Excluded| Included] sub-oid [OID] Level G Description Remove the SNMP server host. Example switch(config)#no snmp-server 192.168.1.
The following table lists the commands for Port Mirroring.
Command 8021x system nasid [words] Level G Description Example The 802.1x system nasid switch(config)# 8021x global configuration command system nasid test1 is used to change the NAS ID 8021x misc quietperiod [sec.] G 8021x misc txperiod [sec.] G The 802.1x misc quiet period global configuration command is used to specify the quiet period value of the switch. The 802.1x misc TX period global configuration command is used to set the TX period. 8021x misc supportimeout [sec.] G The 802.
The following table lists the TFTP Commands. Command backup flash:backup_ cfg Level G restore flash:restore_ cfg G upgrade flash:upgrade_ fw G Description Save configuration to TFTP server. Must specify the IP address of the TFTP server and the file name. Upload configuration from TFTP server. Must specify the IP address of the TFTP server and the file name. Upgrade firmware from the TFTP server. Must specify the IP address of TFTP server and the file name.
Command [Index] [Email address] show smtp no smtp event device-coldstart [Systemlog|SM TP|Both] event authenticationfailure [Systemlog| SMTP|Both] event X -ring-topologychange [Systemlog| SMTP|Both] event systemlog [Link-UP|LinkDown|Both] event smtp [Link-UP|LinkDown|Both] show event no event device-coldstart no event authenticationfailure no event X -ring-topologychange no event systemlog Level Description receipt of alerts Example rcptemail 1 alert@test.
Command no event smpt Level I Description Disable port event for SMTP show systemlog P Display system log client & server information Example switch(config)#interface fastethernet 3 switch(config-if)#no event smtp switch#show systemlog The following table lists the SNTP Commands.
The following table lists the X-Ring Commands.
5.0 Web Based Management This section covers the functions of web based management. There is an embedded HTML web site residing in flash memory in the CPU board of the switch. Web based management provides advanced management features for the network administrator that can be accessed from anywhere on the network through a standard web browser such as Microsoft Internet Explorer (IE). The web based management supports IE 5.0.
5.1 - Web Management Opening Screen 5.3 System Information Use the System Information menu to configuration the following system information: System Name - assign a name for the switch. The maximum length is 64 bytes. System Description - displays the description for the switch. The information is read only and cannot be modified. System Location - assign the physical location for the switch. The maximum length is 64 bytes. System Contact – Enter the designated contact for this switch.
5.2 - System Information Screen 5.4 IP Address Configuration This menu allows you to change the IP address for the switch as well as reconfigure IP settings. Once the IP address has been set, the switch must be rebooted. DHCP - Disable or enable the DHCP client function. When DHCP function is enabled, the system will assign IP addresses to devices from the local DHCP server. Therefore, you do not have to assign the IP addresses. IP Address – Use this option to assign the switch IP address.
5.3 – IP Configuration 5.5 DHCP Server Dynamic Host Configuration Protocol (DHCP) is a protocol for assigning dynamic IP addresses to devices on a network. With dynamic addressing, a device may have a different IP address every time it connects to the network. In some systems, the IP address may change while connected. DHCP supports a combination of static and dynamic IP addresses.
Gateway - The gateway of your network. DNS – The Domain Name Server IP Address of your network. Lease Time (sec) – Specifies in seconds the time period that the system will reset the dynamic IP assignment. Figure 5.4 - DHCP Server Screen When the DHCP server function is enabled, the system will collect DHCP client information which will be displayed in the DHCP Client Entry screen. Figure 5.5 - DHCP Client Entries Screen 5.5.
Figure 5.6 - Port and IP Bindings Screen 5.6 TFTP Transaction The TFTP Transaction screen allows you to update the switch firmware, restore EEPROM value or backup current EEPROM value. 1. Start the TFTP server. 2. Copy the new firmware version image file to the TFTP server. 3. Enter the IP address of the TFTP server. 4. Click Apply to proceed with the update. 5. Enter the firmware filename. Figure 5.7 - Update Firmware Screen 5.
2. Enter the correct Restore File Name. 3. Click Apply to proceed. Figure 5-8 - Restore Configuration Screen 5.8 Backup Configuration This menu allows you to save the current EEPROM value from the switch to the TFTP server. 1. Enter the TFTP server IP address. 2. Enter the correct Backup File Name. 3. Click Apply to proceed. Figure 5.9 - Backup Configuration Screen 5.9 System Event Log The System Event Log allows you to configure the switch so you can collect and view system events. 1.
3. Click Apply. 4. Click Reload to refresh the events log. 5. Click Clear to clear the current events log. 5.10 – System Log Configuration 5.10 SMTP Configuration The system can be configured to send an alert to an email account when specific events occur. The following options can be configured for event notification: Email alert – enable or disable the email alert function SMTP Server IP Address – assign the mail server IP address.
Confirm Password - confirm password Rcpt email address 1 ~ 6 – up to six email accounts can be assigned to receive the alert. Click Apply. 5.12 - SMTP Configuration Screen 5.11 Event Configuration The Event Configuration allows you to select SMTP events. When selected events occur, the system will send out the log information or alerts. Per port log and SMTP events can also be selected. Device cold start – the system will produce a log event when the device executes a cold start action.
5.11 - Event Configuration Screen Port Event Selection – There are three choices for per port events and per port SMTP events. Disabled indicates that no event is selected. o Link Up - the system will produce a log message when port connection is up only. o Link Down - the system will produce a log message when port connection is down only. o Link Up & Link Down - the system will produce a log message when port connection is up and down.
5.12 SNTP Use this menu to configure the Simple Network Time Protocol (SNTP) settings. The SNTP synchronizes the switch clock with the Internet. 1. SNTP Client – set the SNTP function to enable or disable. SNTP is disabled by default. 2. Daylight Saving Time - enable or disable the daylight savings time function. When daylight savings time is enabled, you must also set the daylight savings time period. 3. UTC Timezone - set the switch location time zone.
Local Time Zone Conversion from UTC Time at 12:00 UTC ALA - Alaskan Standard -9 hours 3 am HAW - Hawaiian Standard -10 hours 2 am Nome, Alaska -11 hours 1 am +1 hour 1 pm +2 hours 2 pm +3 hours 3 pm ZP4 - USSR Zone 3 +4 hours 4 pm ZP5 - USSR Zone 4 +5 hours 5 pm ZP6 - USSR Zone 5 +6 hours 6 pm +7 hours 7 pm +8 hours 8 pm +9 hours 9 pm +10 hours 10 pm CET - Central European FWT - French Winter MET - Middle European MEWT - Middle European Winter SWT - Swedish Winter EET - Ea
Local Time Zone Conversion from UTC Time at 12:00 UTC Standard GST Guam Standard, USSR Zone 9 IDLE - International Date Line +12 hours NZST - New Zealand Midnight Standard NZT - New Zealand Table 5.1 – Time Zone Information 4. SNTP Sever URL - set the SNTP server IP address. 5. Daylight Saving Period - Enter the start and ending time for daylight savings time. The daylight savings ending time will different in every year. 6. Daylight Saving Offset (mins) - set the offset time. 7.
5.13 IP Security The final option for network security is the IP security configuration. This function allows you to assign up to ten IP addresses that have permission to access the switch through the web browser. This function adds another level of security for switch management. The IP Security Menu includes the following: IP Security Mode – once the IP Security Mode is enabled, HTTP Server and Telnet Server are available.
5.13 – IP Security Mode 5.14 User Authentication The User Authentication screen allows you to change the authentication login name and password for security. 1. User name – type in the new user name. The default user name is root. 2. Password – type in the new password. The default password is root. 3. Click Apply to make the changes. 5.
5.15 Port Menu Options The Port Menu provides information about the ports as well as options for port configuration. 5.16 Port Statistics The Port Statistics screen provides a view of the current port information. This screen provides current information with real-time packet transfer status for each port. This information can be used for network planning, implementation, diagnosis of heavy traffic, etc. Port: The index column of the ports. Type: Displays the connection media type of the port.
5.15 - Port Statistics Screen 5.17 Port Control In the Port Control menu, you can view port status for each port. Port – select the port to be configured. State - current port status. The port can be set to disable or enable mode. If the port is disabled, it will not receive or transmit packets. Negotiation - set auto negotiation status of port. Speed - set the port link speed. Duplex - set full or half-duplex mode of the port.
5.16 - Port Control Configuration 5.18 Single Port Information By clicking on a single port on the switch panel at the top of the web management screen, single port information will be displayed. 5.17 - Single Port Information Screen 5.19 Port Trunking The Link Aggregation Control Protocol (LACP) provides a standardized means for exchanging information between partner systems.
the link to that Link Aggregation Group and enable its transmission and reception functions. Link aggregation allows you to group up to eight consecutive ports into a single dedicated connection. This feature can expand bandwidth to a device on the network. LACP operation requires full duplex mode. Aggregator setting involves the following: • System priority – a value used to identify the active LACP. The switch with the lowest value has the highest priority and is selected as the active LACP.
Figure 5.18 – Port Trunk Aggregator Setting Once the LACP aggregator has been configured, the information can be displayed through the Aggregator Information screen. Note: The trunk function does not support GVRP and X-Ring. 5.19 - Aggregator Information screen 5.20 State Activity Once the LACP aggregator has been configured, you can configure the port state activity. Port state activity can be set to active or passive.
dynamic LACP trunking. A link with two passive LACP ports will not perform dynamic LACP trunking because both ports are waiting for the LACP protocol packet from the opposite device. The active status will be created automatically if you are the active LACP’s actor when selecting the trunking port. 5.20 - State Activity Screen 5.21 Port Mirroring Port mirroring is a method used to monitor the traffic on a switched network. A specific port can monitor traffic through mirrored ports.
Click Apply to confirm the settings. 5.21 - Port Mirroring Screen 5.22 Rate Limiting Rate limiting allows you to set up the bandwidth rate and packet limitation type per port. Ingress Limit Packet Type – select the packet type to be filtered. The packet types include all types of packets: broadcast/multicast/unknown unicast packets; broadcast/ multicast packets; broadcast packets only.
5.22 - Rate Limiting Screen 5.
5.24 VLAN Configuration Virtual Local Area Networks (VLANs) are logical network groups that limit the broadcast domain. VLANs allows you to isolate network traffic so only members of the VLAN receive traffic from the other VLAN members and not from everyone on the network. Basically, creating a VLAN is the equivalent of reconnecting a group of network devices to another physical switch. However, all the network devices are still connected to the same physical switch.
other information about the packet, such as the protocol. 5.24 – VLAN Configuration 1. Click Add to create a new VLAN group. 2. Enter the Group Name and VLAN ID. 3. Select the members of the VLAN group. 4. Click apply. 5. The VLANs will be displayed. 6. Use the Delete button to remove VLANs. 7. Use the Edit button to modify existing VLANs. 5.24.2 802.1q VLAN The IEEE 802.1q specification covers tagged-based. Therefore, it is possible to create a VLAN across devices from different switch venders.
for configuration. Once 802.1q is enabled, all the ports on the switch belong to default VLAN, VID is 1. The default VLAN cannot be deleted. GVRP allows automatic VLAN configuration between the switch and nodes. If the switch is connected to a device with GVRP enabled, you can send a GVRP request using the VID of a VLAN defined on the switch; the switch will automatically add that device to the existing VLAN. 5.25 – VLAN 802.1q Configuration Screen 1.
Group Configuration To edit the existing VLAN Group: 1. Select the VLAN group in the table list. 2. Click apply. 3. You can change the VLAN group name and VLAN ID. 4. Once you have made the changes, click apply to save the changes. 5.26 – Group Configuration Screen 5.25 RSTP (Rapid Spanning Tree Protocol) Menu RSTP is an evolution of the Spanning Tree Protocol and provides faster spanning tree convergence once a topology change has been made. This switch supports both STP and RSTP.
lowest value has the highest priority and is selected as the root. If you change the value, you must reboot the switch to assign the new path priority number. The value must be multiple of 4096 according to the protocol standard rule. Max Age (6-40) - the number of seconds a bridge waits without receiving STP configuration messages before attempting a reconfiguration. Enter a value between 6 through 40.
5.25.2 RSTP Port Configuration The path cost and priority of every port can be configured through this option. 1. Select the port from the port column. a. Path Cost – the cost of the path to the other bridge from the transmitting bridge at the specified port. Enter a number 1 through 200000000. b. Priority - decide which port should be blocked by priority in LAN. Enter a number 0 through 240. The value of priority must be a multiple of 16. 2.
5.28 - RSTP Port Configuration 5.26 SNMP Configuration Simple Network Management Protocol (SNMP) is the protocol developed to manage nodes (servers, workstations, routers, switches and hubs etc.) on an IP network. SNMP enables network administrators to manage network performance, find and solve network problems, and plan for network growth. Network management provides a system to learn of problems by receiving traps or change notices from network devices implementing SNMP. 5.26.
information • Read/write – enables requests accompanied by this string to display MIB-object information and set MIB objects Click Add. To remove the community string, select the community string to be removed, and click Remove. You cannot remove the default community string set. Agent Mode - select the SNMP version that you want to use it. Figure 5.29 – SNMP Management 5.26.
To remove the community string, select the community string to be removed and click Remove. 5.30 – Trap Configuration 5.26.3 SNMP v3 Configuration To configure the SNMP V3 function, the following tasks should be done. See Figure 5.31 – SNMP V3 Configuration Interface. Configure the Context Table. Assign the context name of the context table. Click Add. Click Remove to remove an unwanted context name. Configure User SNMP v3 User Table. User ID – Enter a user name.
Group Name – set up the group name. Click Add to add the group information. Click Remove to remove group information. Configure SNMP V3 Access Table Context Prefix – set up the context name. Group Name – set up the group Security Level – select the access level between the following choices: • NoAuthNoPriv • AuthNoPriv • AuthPriv Read View Name – set the read view Write View Name – set up the write view. Notify View Name – set up the notify view.
5.32 – SNMP V3 Interface Figure 5.
5.27 QoS Configuration Use the QoS configuration menus to configure the following: QoS policy Priority setting Per port priority setting COS TOS QoS Policy and Priority TYpe QoS Policy – select the QoS policy rule. • 8,4,2,1 weight fair queue scheme - the switch will follow the 8:4:2:1 rate to process priority queue from highest to lowest queue.
5.
Port Based Priority Use this screen to configure the priority level per port. Port 1 ~ 9 – each port has four priority levels – High, Middle, Low and Lowest. Click Apply to save the configuration. COS Configuration Use this screen to set the COS priority level. COS priority - set the COS priority level 0~7: High, Middle, Low, Lowest. Click Apply to save the configuration. TOS Configuration Use this screen to set the TOS priority level. TOS priority - the system provides 0~63 TOS priority levels.
Message Query Description A message sent from the querier (IGMP router or switch) asking for a response from each host belonging to the multicast group. A message sent by a host to the querier to indicate that the host Report wants to be or is a member of a given group indicated in the report message. Leave A message sent by a host to the querier to indicate that the host Group is no longer a member of a specific multicast group. Table 5.
5.29 X-ring X-ring provides a faster redundant recovery than the spanning tree topology. The action is similar to STP and RSTP, but the algorithms that are used are not the same. To use the X-ring topology, the X-ring function must be enabled and the switch must assign two member ports in the ring. One switch in the X-ring group should be set as a backup switch that one of two member ports will be blocking. port, and the other port is the working port.
standby or back up connection that is activated in case the operating connection fails. Click Apply to save the configuration. 5.34 - X-ring Interface Note: When the X-ring function is enabled, RSTP must be disabled. The X-ring function cannot exist at the same time as RSTP. 5.30 Security Menu Use the Security menu to configure 802.1x and port security by MAC address. 5.30.1 802.1X Radius 802.
IEEE 802.1x protocol - enable or disable 802.1x protocol. Radius Server IP - set the Radius Server IP address. Server Port - set the UDP destination port for authentication requests to the specified Radius Server. Accounting Port - set the UDP destination port for accounting requests to the specified Radius Server. Shared Key - set an encryption key to be used during authentication sessions with the specified radius server. This key must match the encryption key used on the Radius Server.
Disable - the specified port is required to be held in the authorized state Click Apply to save the configuration. 5.36 – 802.1x Per Port Setting Interface Miscellaneous Configuration Quiet Period - set the period during which the port doesn’t try to acquire a supplicant. TX Period - set the period the port waits for retransmit (next EAPOL PDU) during an authentication session. Supplicant Timeout - set the period of time the switch waits for a supplicant response to an EAP request.
re-authenticated. Select Apply to save the configuration. 5.37 – 802.1x Miscellaneous Configuration 5.30.2 MAC Address Table The MAC Address Table Menu allows you to add a static MAC address. The static MAC address will remain in the switch's address table, regardless of whether or not the device is physically connected to the switch. This eliminates the need for the switch to re-learn a device's MAC address when the disconnected or powered-off device once again becomes active on the network.
5.38 – Static MAC Address Interface MAC Filtering By filtering MAC addresses, you can enhance the security on your network. The MAC Filtering screen allows you to add and delete MAC addresses. To add a MAC Address for filtering: 1. MAC Address - Enter the MAC address to be filtered. 2. Click Add to save the configuration. 3. The MAC address will be displayed in the table. You can delete a MAC address from the filtering table by selecting the MAC address and clicking Delete.
5.39 – Filter MAC Address Interface All MAC Addresses You can view the MAC address and the related devices’ MAC address connected to the port. 1. Select the port. 2. The selected port for static MAC address information will be displayed. 3. Select Clear MAC Table to clear the current port static MAC address information. 5.
5.31 Factory Default Settings You can return the factory default settings by choosing Factory Default from the Main Menu. Keep current IP address setting – You may either keep the current IP address or reset the IP to the default IP address. Use the Space key to make the change. Keep current username and password – You may either keep the current username and password or reset to default username and password (root/root). Use the Space key to make the change.
6.0 Troubleshooting All Waters’ switching products are designed to provide reliability and consistently high performance in all network environments. The installation of Waters’ 2109 and 1009 switch is a straightforward procedure (See Sections 3-5). Should problems develop during installation or operation, this section is intended to help locate, identify and correct these types of problems. Please follow the suggestions listed below prior to contacting your supplier.
When Calling for Assistance Please be prepared to provide the following information. 1. A complete description of the problem, including the following: a. The nature and duration of the problem b. Situations when the problem occurs c. The components involved in the problem d. Any particular application that, when used, appears to create the problem 2. An accurate list of Waters Network Systems product model(s) involved. Include the date(s) that you purchased the products from your supplier. 3.
warranty-repaired units to the sender with shipping charges prepaid (see Warranty Information at the end of this manual for complete details). However, if Waters cannot duplicate the problem or condition causing the return, the unit will be returned as: No Problem Found. Waters Network Systems reserves the right to charge for the testing of non-defective units under warranty. Testing and repair of product that is not under warranty will result in a customer (user) charge. 6.
7.0 Warranty Waters Network Systems’ Warranty Statement Waters Network Systems’ products are warranted against defects in materials and workmanship. The warranty period for each product will be provided upon request at the time of purchase. Unless otherwise stated, the warranty period is for the useable life of the product.
ProMedia Converters 3 Years from date of manufacture (see note) Note: Warranty period for any and all external power supplies is one (1) year from date of purchase. EXCEPT FOR THE EXPRESS WARRANTY SET FORTH ABOVE, WATERS NETWORK SYSTEMS GRANTS NO OTHER WARRANTIES, EXPRESSED OR IMPLIED, BY STATUTE OR OTHERWISE, REGARDING THE PRODUCTS, THEIR FITNESS FOR ANY PURPOSE, THEIR QUALITY, THEIR MERCHANTABILITY, OR OTHERWISE.