Installation Guide

B
A
B
A
Washer
Filter Screen
Flow Regulator
Fixed Mount
Washer
Washer
Filter Screen
Flow Regulator
Waterpik
®
Handheld
Bracket
Hose
Connector
Nut
Premium Design
Handheld Bracket
with
Vacuum Breaker
Vacuum
Breaker
Installation
Fixed Mount Models
Installation
Modèles à montage fixe
Components
Your showerhead comes with one of the respective hardware sets
shown below.
Composants
Votre pomme de douche est livrée avec l’un des ensembles respectifs
illustrés ci-dessous.
Care and Cleaning
• Clean filter screen at least once a year, or whenever you notice a drop
in water pressure. To remove, unscrew with pliers by turning
counterclockwise.
• Cleaning is required when mineral deposits appear on the spray
orifices to maintain proper working conditions. Clean by soaking in
household vinegar.
• Do not clean or rinse any part with harsh chemicals, heavy duty
cleaners, or abrasives; this may damage parts or finish and may void
warranty.
Note
Vacuum Breaker (some models)
The State of Wisconsin and the City and County of Los Angeles,
California, U.S.A. require vacuum breakers on all hand-held shower-
heads.
Vacuum breakers are required by certain plumbing codes in order to
protect water supplies from potential back-flow. The vacuum breaker
(located within the bracket) may discharge a small amount of water
when you turn on your shower. It will also drain a small amount of water
when you turn off your shower. Both are normal operative conditions.
ENGLISH FRANÇAIS
FN 20009510-F AH FN 20009510-F AH
Waterpik
®
brand showerheads are equipped with an OptiFlow
®
regulator that limits maximum water flow to 2.5 gallons per minute at
80 psi as mandated by U.S. federal law.
Les pommes de douche de la marque Waterpik
®
sont équipées d’un
régulateur OptiFlow
®
qui limite le débit d’eau maximal à 2,5 gallons
par minute à 80 lb/po
2
, conformément aux exigences de la loi fédérale
américaine.
EN FRANÇAIS AU VERSO
Note: Drawings may not match your product. Remarque: Les illustrations peuvent ne pas correspondre a´votre produit.
Rondelle
Rondelle
Rondelle
Tamis-filtre
Tamis-filtre
Régulateur de débit
Régulateur de débit
Bride Waterpik
®
pour pomme
à main
Montage fixe
Raccord
de tuyau
Écrou
Bride pour pomme
à main de design
première qualité
avec brise-vide
Brise-Vide
Instruction
Manual
Manuel
d’instructions
Model # is located by barcode.
Please write your model # on your sales receipt or below.
Le n˚ de modèle est indiqué près du code-barre.
inscrire le n˚ de modèle sur la facture d’achat, ou ci-dessous
DATE: 2 June 2010 CLIENT: Water Pik, Inc.
FILENAME: FN20009510-FAH_PlasticPivot.indd DESCRIPTION: Waterpik Showerhead Instruction Manual
FILE TYPE: Adobe InDesign CS4 PREPARED BY: Brian Colon FORM: 20009510-F AH
SIZE FLAT: 17” x 11.25” SIZE FOLDED: 3.43” x 3.75” (3-7/16 x 3-3/4) FOLDS: Indicated
DIELINE: N/A INK: Black
NOTES:
Hand-Held Models
For hand-held models, slightly loosen nut
on bracket assembly and position hose
connection downward. Tighten pivot ball
to pipe. Ensure nut is secure by hand
tightening.
Modèles à main
Pour les modèles à main, desserrer
légèrement la écrou sur l’ensemble de la
bride et positionner le raccord de tuyau
vers le bas. Serrer la boule d’articulation
sur le tuyau. S’assurer que la base de
la écrou est bien fixée en la serrant
manuellement.
Operation
A. If your unit has
more than one set-
ting, spray pattern
is controlled by
outside trim ring.
B. If your unit has a
custom pressure
control ring, water
flow is controlled by
sliding the ring tab
left or right.
Fonctionnement
A. Si votre pomme de douche comporte plus de 1 réglage, la forme
de dispersion du jet est contrôlée par la bague de garniture
externe.
B. Si votre pomme de douche est munie d’un anneau de contrôle de
la pression, le débit d’eau est contrôlé en glissant la languette de
l’anneau à gauche ou à droite.
Limited Lifetime Warranty
Water Pik, Inc. warrants to the original purchaser of this product that
it is free from defects in material and workmanship for as long as
the original purchaser owns this product. Water Pik, Inc. will replace
any part of the product which in our opinion is defective, provided
that the product has not been abused, misused, altered or damaged
after purchase. (This includes damage due to use of tools or harsh
chemicals.) In the event an item has been discontinued we will replace
with what we deem to be the closest product. Water Pik, Inc. is not
responsible for labor charges, installation, or other consequential
cost. The responsibility of Water Pik, Inc. shall not exceed the original
purchase price of the product. This warranty gives you specific legal
rights. You may also have other rights that vary where you reside. Save
your receipt as proof of purchase is required for warranty action.
Have any questions or need assistance?
In the U.S., call our toll-free
Customer Assistance Line,
1-800-525-2774.
If in Canada, call our toll-free
Customer Assistance Line,
1-888-226-3042
If outside the U.S., write us at:
Water Pik, Inc.
1730 East Prospect Road
Fort Collins, CO 80553-0001
U.S.A.
www.waterpik.com
Hand tighten hose end to bracket
and handle. Do not use pliers or
wrench to connect hose ends to
showerhead or bracket.
Troubleshooting Guide
Problem Solution
No water flow from installed
shower head:
a Confirm previous shower washer is not in
the j-pipe.
b Confirm the hose is properly installed, try
switching ends.
c Confirm there is only one washer in the
pivot ball.
Low water pressure or
missing spray patterns
a Clean shower head in vinegar/water
solution. (See care section).
b Clean screen and flow regulator.
Leaking at pipe pivot ball
connection:
a Confirm one single washer is seated on
top of the screen.
b Grate bar of soap across the j-pipe
threads to act as a sealant.
Showerhead and/or bracket
stiff to change angle
a Immerse pivot ball and large nut of the
bracket in hot water or use a blow dryer
for several minutes and then use a towel
to loosen the large nut.
For Fixed Mount: install FM shower head
to provide additional leverage to change
angle of spray. (Contact Water Pik for
further assistance).
Waterpik
®
(stylized) is a trademark of Water Pik, Inc. registered in the EU, Switzerland,
Mexico, Canada, and United States.
Waterpik
®
is a trademark of Water Pik, Inc. registered in Argentina, Australia, Austria,
Canada, China, Czech Republic, Hungary, India, Japan, Poland, Russian Federation,
South Africa, Switzerland, Ukraine, and the United States.
OptiFlow
®
is a trademark of Water Pik, Inc. registered in Australia, Canada, the EU, Hong
Kong, Korea and the United States.
©2010 Water Pik, Inc.
Water Pik, Inc.
1730 East Prospect Road
Fort Collins, CO 80553-0001
U.S.A.
www.waterpik.com