Installation Guide

ManualsBrandsWaterless No-Flush urinal ManualsBathSonora Composite Waterless Urinal No-Flush in White Color

INSTALLATION INSTRUCTIONS

HPC Models #2003, #2004 and #2005

VC Models #2103 and #2104

For additional installation instructions that pertain to each individual urinal, please see next two pages.

BOX CONTENTS:

2-EcoTrap® Inserts; 2-Wall Hangers; 4-Washers; 4-Plastic Anchors;

4-Screws; 2-All-Thread 5/16” Studs with nuts; 1-Rubber Gasket;

1- Brass Flange (VC urinal ONLY)

Model #2104 ONLY: 2-EcoTrap® Inserts; 1- Wall Hanger;

2-Washers; 2-Plastic Anchors; 2-Screws; 2-All-Thread 5/16” Studs

with nuts; 1-Rubber Gasket; 1- Brass Flange

TOOLS NEEDED:

Screwdriver; 5/16” (7.9mm) Masonry Drill Bit and Drill; Putty

Knife; Water Supply Cap (for retrot only); Wrench; Caulk

BEFORE YOU BEGIN:

• Do not install No-Flush™ urinals without prior

waste line clean out. Do not double trap (remove any

other trap in drain line).

• Please assure that the new urinal has the

correct rough-in dimensions.

• When working with highly polished plastic or ceramic

products, please use care in handling the unit

during installation to avoid scratches or

chip marks.

• Over-tightening bolts and screws may result

in damage to the urinal.

• Measure drain line height for correct urinal height.

TO REMOVE EXISTING URINAL:

Turn o the water supply. Flush the urinal to drain valve and

scoop or sponge out remaining water in urinal. Disconnect the

ushometer valve completely and cap water supply line at tile.

Remove urinal shell from wall and clean o any residues from

wall and ange.

BEFORE YOU INSTALL URINAL:

Do not install No-Flush™ urinal without prior waste line clean

out. Existing scaling and debris in the waste line will inhibit the

ow of waste from Waterless™ urinal and its proper functioning

can not be guaranteed. No-Flush™ urinals are engineered, how-

ever, to reduce waste line scaling.

TO INSTALL NO-FLUSH™ URINAL:

• Assure that ange holes are lined up horizontally. Insert

5/16” All-Thread studs into existing ange holds.

• Set supplied rubber gasket on existing ange. Do not use

wax gasket. If using wax gasket, assure that no wax materials

protrude into interior drain line openings.

• SEE PAGE 4 FOR SPECIFIC URINAL

MOUNTING INSTRUCTIONS.

• Install wall hanger(s) with provided anchors and screws.

• Carefully align/set urinal onto wall hanger(s) and lower

urinal onto ange studs through AllFlange™ recess in urinal.

If alignment is needed, remove urinal, reset hanger(s) and

hang urinal again as described above.

• Use washers and nuts and hand tighten on studs to hold urinal

in place. Then tighten nuts evenly. Avoid over-tightening.

• Caution: Do not rock or lift urinal after placement. Seal

gasket may slip and not be water tight. Do not double

ring for leak repair.

• Using a bucket of water, at least 5 gallons, pour water down

urinal drain hole to test seal tightness. Check for leaks on

bottom of urinal and wall.

• Caulk urinal, leaving approximately 8” (203mm) on bottom

of urinal uncaulked. Attach tile label above urinal on wall

(where available).

INITIAL START-UP:

Wipe urinal clean with soft moist cloth. Take enclosed plas-

tic EcoTrap® insert. Fill it with water under faucet in sink. Set

EcoTrap® insert into trapway. Push down below rim of trapway.

Add 3 0z. of BlueSeal® trap liquid. Done! (Note: Plumber’s grease can

be used around edges of EcoTrap® insert to ease insertion into trapway.)

CLEANING AND CARE:

Do not use any harsh abrasive cleaners as those can harm

the surface eectiveness and thereby void the product’s

warranty. NviroClean™ (#1614) is a very eective and e-

cient cleaner. Simply spray and walk away!

NOTE:

No ushometer needed for xture, provide suitable reinforcements for all wall supports and carriers. ADA: Requires urinal rim to

be mounted 17” above nished oor. Dimensions for xtures are nominal and may vary within the range of tolerances established

by ANSI Standard A112.19.19 and ANSI Z124.9. Measurements are subject to change or cancellation. No responsibility is assumed.

UPC®; others. For copper DWV drain lines ascertain and document that the installed lines are not corroded or show “channeling”.

High Performance Composite = HPC Vitreous China = VC

Please leave this Installation/Care sheet with the owner/user as it contains important information.