Full Product Manual

ManualsBrandsWater Tech ManualsOtherPool Blaster Max for Above Ground Pools

MAINTENANCE

Important Tips:

• Store your Pool Blaster in a clean, dry place when not

in use. Do not leave it underwater, in direct sunlight, or

exposed to extreme heat or cold.

• You may clean the Pool Blaster body with soap and

water. Avoid using solvents when cleaning plastic

parts. Most plastics are susceptible to damage from

various types of commercial solvents and may be

damaged by their use. Use clean cloths or paper

towels to remove dirt, dust, oil, grease etc.

• The On-Off knob should be periodically lubricated with

a silicon-based grease

• The ON/OFF knob should remain disconnected from

the unit and left hanging from the attached lanyard

until the unit is ready to be used.

CAUTION: Do not at any time let brake ﬂuids, gasoline, pe-

troleum-based products, penetrating oils, etc. come in contact

with plastic parts. They contain chemicals that can damage,

weaken, or destroy plastic.

WARNING: Do not attempt to modify this tool or create ac-

cessories not approved for use with this tool. Any such alteration

or modiﬁcation is misuse and could result in a hazardous condi

tion leading to possible serious injury. The batteries and motor

are factory sealed in the motor box, and CANNOT BE REPLACED.

Do not attempt in any way to destroy or disassemble motor box

or any of its components. Instead, take your Pool Blaster to an

authorized service center. Failure to follow these instructions may

void your warranty agreement.

• General maintenance of your Pool Blaster requires you

occasionally clean off the O-rings on the “ON-OFF”

knob and add silicone lubricant/sealant. This will ensure

easier turning and a water-tight seal. This lubricant is

available at your local pool & spa or hardware retailer.

• In the Nose Cap (Part No. PBA002) there is a Flapper

Valve. To keep the Nose Cap Flapper Valve moving

freely, clean the valve after every use. This will help

to keep dirt inside the Pool Blaster after the cleaner is

removed from the pool.

Service Information

NOTE: Any repairs requiring disassembly must be performed by

a Water Tech Authorized Service Center. For the repair center

nearest you call us toll free at 1-800-298-8800. Unauthorized

repairs will void the warranty.

Storing the Pool Blaster

NOTE: State of the art Nickel-Metal Hydride batteries power the

Pool Blaster. These are the same batteries used in many portable

phones. In order to properly ventilate and cool the batteries

and drive system a certain amount of space is left open in the

Pool Blaster body. As a result, from time to time, water may enter

the unit. In order to allow for any water to be drained you should

remove the On-Off Knob after each use, turn the machine so the

knob is towards the ﬂoor and tilt side to side in all directions. The

amount of water may be very small or not noticed at all. After

removing any water use a blow dryer on warm setting to dry any

moisture build-up on the inside of the motor box. Water entering

the Pool Blaster body presents no safety hazard and should be

drained to avoid any chance of long-term corrosion. The batter

ies and motor in the Pool Blaster are long lasting and proper care

will help to prolong the life of your appliance.

NOTE: Remove Pool Blaster from charger before storage.

When not in use, your Pool Blaster should be stored indoors, in a

clean dry location sheltered from direct sunlight, extreme tem

peratures and rain. Do not store the Pool Blaster in a garage or

anywhere the unit could freeze. Storing the Pool Blaster in areas of

high humidity can affect battery performance over time.

The ON/OFF knob should remain disconnected from the unit and

left hanging from the attached lanyard until the unit is ready to

be used.

For your convenience the Pool Blaster has an oval opening in the

pool pole adaptor on which you can hang the unit.

Long Term Storage

Follow the above storage instructions and unplug the charger

from the electrical outlet.

Your Pool Blaster should be charged once a month during long-

term storage to maintain the battery pack. DO NOT leave the

Pool Blaster charging for a period of more than 24 hours.

When charging for the ﬁrst time after long-term storage, your

Pool Blaster may take 2-3 uses before maximum performance is

achieved.

The ON/OFF knob should remain disconnected from the unit and

left hanging from the attached lanyard until the unit is ready to

be used.