Full Product Manual

HOW TO USE YOUR POOL BLASTER
CAUTION: The Pool Blaster is designed for under
water use only.
OPERATING TEMPERATURES
Unit must be submerged in water to operate properly.
Maximum operating temperature is between +5˚C (41˚F)
and+40˚C (104˚F). Maximum operating depth is (15 ft).
Your Pool Blaster is designed for use in 3 different ways to
vacuum your pool or spa:
A.
Vacuum using the handle and the vacuum head removed.
B. Vacuum using the handle and attached vacuum head,
with either wheel or brush attachments depending on
pool type.
C. Vacuum using a standard pool accessory pole (not
supplied) with the attached vacuum head.
Caution: Vacuum Head must be used when using a pole.
WARNING: Never use your Pool Blaster without
the filter bag/seal ring and nose cap properly in place.
Doing so will VOID the warranty.
Using a standard pool pole
The pole attachment on your Pool
Blaster is designed to accommodate
any standard pole. To attach a pole,
simply press down on the alignment
pins on the pole retaining spring clip.
Aligning the holes, slide the pole onto
the Pool Blaster and release the clip.
WARNING: Do not lean on pole or use pole to
support weight.
Once your Pool Blaster is set-up for use, you may put it in
your pool or spa.
• Bring your Pool Blaster to the side of the Pool or
Spa and turn it on by turning the
On-Off knob all the way to the “On” position. This
must be done outside of the
water before it is submerged.
• Once the Pool Blaster is “On” it can be com
-
pletely submerged in water and is ready for use.
• This appliance is designed to be in water only
when in the “ON” position and has battery power.
Excessive leaking can occur when not running
and void the warranty. Never leave your Pool
Blaster in the water when it is off.
NOTE: There are two ways to remove the unit from the
pool:
WHEN USING HANDLE: Lift from pool with the nose facing
up to allow the water to escape from the back and sides.
WHEN USING A POOL POLE: Remove the unit from the
pool with the bottom facing upwards and the handle fac-
ing down. This will allow the water to escape and keep the
dirt inside
Cleaning the reusable filter bags
For maximum cleaning efficiency the filter bag/seal ring
should be checked, emptied, and cleaned after each
use or whenever you notice the performance of you Pool
Blaster declining.
To clean the filter bag
• Unplug the Pool Blaster from the charging outlet
before changing the filter or performing any
other routine maintenance.
• Place the Pool Blaster on its end (remove the
vacuum pole, if attached).
• Unlatch the nose cap
• Remove the filter bag/seal ring by pulling it out of
the funnel.
• Invert the filter bag/seal ring, shsake out the large
debris and rinse with a garden hose or in a sink.
Note: Do not clean in a washing machine or
with detergent.
• Re-insert the filter bag when finished.
• Note: Your reusable filter bag should be re
-
placed if the seal ring is worn or if the bag is torn.
Choosing the Proper Filter Bag
Standard All-Purpose Filter Bag
The Pool Blaster, with its Standard Filter Bag is intended
for routine pool maintenance only. Should there be an
excessive amount of debris (ie. when opening the pool for
the season, cleaning following major storm activity or other
high level debris occurances) be aware that you will have
to empty the Fliter Bag much more often than normal. It
may take several cleaning and recharging cycles to clean
your pool.
Microfilter Bag
The Microfilter Bag should only be used to remove fine
sand, silt, algae and other small particles from your pool.
Be aware that due to the high degree of filtration that this
bag affords. It fills much more rapidly than the All-Purpose
bag and therefore must be emptied frequently during
pool cleaning to insure optimum performance.
8