Water Tech TM POOL BLASTER MAX ® Handheld Pool & Spa Cleaner Use and Care Manual IMPORTANT: DO NOT RETURN THIS PRODUCT TO THE STORE Should you have any problems or questions concerning your product you should contact Water Tech’s Customer Service Division toll free in the U.S. at 1-800-298-8800 or via fax at 1-800-488-0700 or via the web at www.PoolBlaster.
Warning This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Before Initial Use CONGRATULATIONS on your purchase of a top-quality Water Tech product which has been thoroughly tested to meet our exacting quality control standards. The Pool Blaster vacuum is powered by Nickel-Metal Hydride batteries. These batteries will operate at their peak after the second or third charge. A precise amount of space is left open in the Pool Blaster body to properly ventilate and cool the batteries, seals and drive system.
SERVICE & IMPORTANT SAFEGUARDS Service Information Use extra care when cleaning on stairs. WARNING: Any repairs requiring disassembly should be performed by a Water Tech Authorized Service Center. For repairs please go to www.watertechcorp.com for more information or call 1-800-298-8800. Make sure the Pool Blaster is unplugged from the charger and in the “off” position before cleaning, filter change or any other routine maintenance.
ITEM No. 1 2 3 4 5 6 7 8 DESCRIPTION Vacuum Head Vacuum Head Brushs Vacuum Head Wheels Nose Cap All Purpose Filter Bag w/ Seal Ring Pool Blaster Battery Charger Spring Clip ADDITIONAL PARTS AVAILABLE FOR PURCHASE Sand & Silt bag (part No. PBW022SS) Microfilter Bag (part No. PBW022MF), to be used in conjunction with the Sand & Silt bag Shallow Water Hose Attachment (part No. PBASHA) * U.S. Charger (part No. PBA099L) * European 230V Charger (part No. WT3843) PART No. QTY.
SETTING UP YOUR POOL BLASTER FOR USE Charging the Battery Pack TO RECHARGE THE CLEANER 1.Turn the knob counterclockwise to remove the On-Off Knob. This will expose the charging jack connection. NOTE: When removing the On/Off knob it is normal to hear air escaping. The air inside has simply expanded from being heated by the motor. PRECAUTIONS: • Make sure power supply is normal household voltage, 120 volts, 60 Hz (240 volts, 50Hz International), AC only.
PREPARING THE VACUUM HEAD / INSERTING THE FILTER BAG SETTING UP YOUR POOL BLASTER FOR USE Inserting Wheels and Brushes in the Vacuum Head Inserting the Filter Bag and Nose Cap Your Pool Blaster has been configured with wheels and brushes at the factory in a manner which we have found perform best in most swimming pool applications.
HOW TO USE YOUR POOL BLASTER CAUTION: The Pool Blaster is designed for under Once your Pool Blaster is set-up for use, you may put it in your pool or spa. water use only. OPERATING TEMPERATURES Unit must be submerged in water to operate properly. Maximum operating temperature is between +5˚C (41˚F) and+40˚C (104˚F). Maximum operating depth is (15 ft).
MAINTENANCE Important Tips: • Store your Pool Blaster in a clean, dry place when not in use. Do not leave it underwater, in direct sunlight, or exposed to extreme heat or cold. • You may clean the Pool Blaster body with soap and water. Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths or paper towels to remove dirt, dust, oil, grease etc.
LIMITED WARRANTY Water Tech Corp (“WT”) warrants this product, including supplied accessories against defects in material or workmanship for the time periods as set forth below. Pursuant to this Limited Warranty WT will, at its option (i) repair the product to the original specifications or (ii) replace the product with a new or refurbished product. In the event of a defect, these are your exclusive remedies.
COMMON QUESTIONS Do not use for at least 24 hours. If possible, you can speed the drying process with a blow dryer. To avoid serious injury or damage, do not replace the knob or attempt to charge or operate your Pool Blaster until it is completely dry. Q: The ON-OFF knob has become difficult to turn. What can I do? A: Clean off the O-rings and add silicone lubricant/sealant. This will ensure easier turning and a better water tight seal. Refer to the maintenance section for more information.
IMPORTANT: DO NOT RETURN THIS PRODUCT TO THE STORE Should you have any problems or questions concerning your product you should contact Water Tech’s Customer Service Division toll free in the U.S. at 1-800-298-8800 or via fax at 1-800-488-0700 or via the web at www.PoolBlaster.com Water Tech Corp 44 West Ferris St. East Brunswick, NJ 08816 USA Toll Free: 1-800-298-8800 (US only) Email: support@WaterTechCorp.com www.WaterTechCorp.
