Product data

UJA1167 All information provided in this document is subject to legal disclaimers. © NXP Semiconductors N.V. 2014. All rights reserved.
Product data sheet Rev. 2 — 18 April 2014 42 of 60
NXP Semiconductors
UJA1167
Mini high-speed CAN system basis chip with Standby/Sleep modes &
watchdog
Voltage source: pin V1
V
O
output voltage V
BAT
= 5.5 V to 18 V;
I
V1
= 120 mA to 0 mA;
V
TXD
=V
V1
4.9 5 5.1 V
V
BAT
= 5.65 V to 18 V;
I
V1
= 150 mA to 0 mA;
V
TXD
=V
V1
4.9 5 5.1 V
V
BAT
= 5.65 V to 18 V;
I
V1
= 100 mA to 0 mA;
V
TXD
=0 V; V
CANH
= 0 V
4.9 5 5.1 V
V
ret(RAM)
RAM retention voltage difference between V
BAT
and V
V1
V
BAT
= 2 V to 3 V;
I
V1
= 2mA
--100mV
V
BAT
= 2 V to 3 V;
I
V1
= 200 A
[1]
10 mV
R
(BAT-V1)
resistance between pin BAT and
pin V1
V
BAT
= 4 V to 6 V;
I
V1
= 120 mA
--5
V
BAT
= 3 V to 4 V; I
V1
= 40 mA - 2.625 - 
V
uvd
undervoltage detection voltage V
uvd(nom)
= 90 % 4.5 - 4.75 V
V
uvd(nom)
= 80 % 4 - 4.25 V
V
uvd(nom)
=70% 3.5 3.75 V
V
uvd(nom)
= 60 % 3 - 3.25 V
V
uvr
undervoltage recovery voltage 4.5 - 4.75 V
I
O(sc)
short-circuit output current 300 - 150 mA
Voltage source: VEXT (UJA1167TK/VX only)
V
O
output voltage V
BAT
= 6.5 V to 18 V;
I
VEXT
= 30 mA to 0 mA
4.9 5 5.1 V
V
uvd
undervoltage detection voltage 4.5 - 4.75 V
V
ovd
overvoltage detection voltage 6.5 - 7 V
I
O(sc)
short-circuit output current 125 - 30 mA
Voltage source: INH (UJA1167TK)
V
O
output voltage I
INH
= 180 AV
BAT
 0.8
-V
BAT
V
R
pd
pull-down resistance Sleep mode 3 4 5 M
Serial peripheral interface inputs; pins SDI, SCK and SCSN
V
th(sw)
switching threshold voltage 0.25V
V1
-0.75V
V1
V
R
pd(SCK)
pull-down resistance on pin SCK 40 60 80 k
R
pu(SCSN)
pull-up resistance on pin SCSN 40 60 80 k
I
LI(SDI)
input leakage current on pin SDI 5-+5A
Serial peripheral interface data output; pin SDO
V
OH
HIGH-level output voltage I
OH
= 4mA V
V1
 0.4 - - V
V
OL
LOW-level output voltage I
OL
= 4 mA - - 0.4 V
Table 46. Static characteristics
…continued
T
vj
=  40  C to +150  C; V
BAT
= 3 V to 28 V; R
(CANH-CANL)
=60  ; all voltages are defined with respect to ground; positive
currents flow into the IC; typical values are given at V
BAT
= 13 V; unless otherwise specified.
Symbol Parameter Conditions Min Typ Max Unit