Polishing Compact Unit WP-Ex 3000 II with Speed Regulator REF 146977 (115 V / 50-60 Hz) USER MANUAL
Dear customer, Thank you for choosing a product from the Wassermann range. Wassermann DentalMaschinen incorporates the highest standards of quality and the latest technology. In order to enjoy maximum performance and years of trouble-free operation, please read this user manual carefully before you connect this device and start work, and operate the device according to the recommended guidelines.
Contents 1 Features.............................................................................................................................4 2 Safety Symbols used in this Manual..................................................................................5 3 Safety Guidelines...............................................................................................................5 4 Responsibility for Operation or Damage..........................................................................
1 Features • 115 V version • Compact and powerful stainless steel polishing unit for daily lab use • Powerful, durable and maintenance-free induction motor • 2 settings, 1500 bzw.
2 Safety Symbols used in this Manual Warning! This is a warning of risk situations and dangers. Failure to observe this warning could be life-threatening. These warnings has to be observed. Information! This symbol draws your attention to specific features that has to be observed. 3 Safety Guidelines Configuring and operating this equipment requires precise knowledge and observance of the instructions in this user manual. The equipment is designed only for its intended application.
4 Responsibility for Operation or Damage The responsibility for operating the device lies exclusively with the owner or user if said device is incorrectly serviced, maintained or altered by persons not employed by an authorised dealer or if the device is used in a manner contrary to its specified purpose. The unit has to be maintained and operated in accordance with this user manual. Wassermann Dental-Maschinen GmbH is not responsible for damage arising from the nonobservance of these instructions.
6 Before Starting 6.1 Transport Before transporting the unit, ensure that it has been unplugged from the power socket. Make sure that it is packed correctly in order to avoid accidental damage. Be sure to check for any transport damage when unpacking the goods. Note down any damage if found. 6.2 Installation Open the box, remove the packing materials, and carefully lift out the device and accessories. Check the included accessories.
6.3 Storage If the unit is to be stored for an extended period, protect it from moisture and dust. The polisher location is very important when it comes to workplace safety, even if it is only to be set up there for a short period. The room should be dry, well ventilated and vibrationfree. An even temperature and wooden supports also help. The polisher should not be stored outdoors. 7 Installation/ Start-up Before starting the unit, connect up the following: 7.
8 8.1 Operation General Operating Instructions All instructions for using the unit, whether in verbal or written form, are based on our own experience and experimentation and can only be regarded as guidelines. 8.2 Handling of the Unit 3 2 1 2 3 The WP-3000 Ex II is turned on with the main switch. The motor speed is controlled using the arrow keys. The extraction and the LED spot can be manually turned on and off. Main Switch: 1 The device is powered. The lighting is on.
5 7 4 6 Display Toogle switch: 4 on and switch-off of the suction Button 5 speed 1500 min-1 bzw.
9 Troubleshooting Fault Spindles do not stay in place Cause Solution Spindles too loose Use light hammer taps to fix spindles in place Spindles cannot be undone Spindles located too firmly on tapers Contact our service department Little to no suction Filter bag full Replace filter bag Bearing noise Faulty bearing Contact our service department Light does not work LEDs defective No function ATTENTION: The LEDs right and left are in series.
10 10.1 Care and Maintenance Cleaning Disconnect the power plug before starting any maintenance work. The identification plate has always to be kept in easily legible condition and has not to be removed. Remove external dirt from time to time with some form of cold cleaner. Use only cold cleaners to avoid damaging the paintwork or removing the lettering. The equipment should be cleaned at regular intervals to ensure trouble-free operation.
10.2 Maintenance The unit does not require any servicing. Just make sure that the device is kept clean and a matched filter change should take place according to the needs. The unit is equipped with 2 extra large micro fine dust filterbag. If the suction power decreases, please change the filter! 10.2.1 Filter and Changing the Filter Open the two clamps on the rear panel. Then the cover can be slided back and be removed.
10.2.2 Changing the Integrated LEDs E A C B C C D C A B Disconnect the power plug before starting any maintenance work. ATTENTION: The LEDs right and left are in series. That means both LEDs do not work although perhaps only one of them is faulty. Please check this in advance and replace only the faulty LEDs. • To open the service covers [A] on the right and left side of the unit unscrew the four screws [B] by using an Allen wrench.
10.2.3 Changing the Fuse The fuse of the WP-Ex 3000 II is located next to the socket of the supply line plug. Remove the damaged fuse and insert a new one. 10.3 Repairs Servicing or repairs to the unit has only to be carried out by qualified technicians. Only original spare parts are to be used. Responsibility for the product is voided if unauthorised persons alter it or if inappropriate components are installed. 10.4 Spare Parts If necessary please contact our service hotline phone. 10.
10.6 Scope of Delivery/ Accessories Included parts: Brush spindle right Brush spindle left Supply line Micro fine dust filterbag, 1 set =2 pieces Polishing trough, 2 pieces Drawer (W 621 x H 23 x D 219 mm) Storage bowl (W 257 x H 40 x D 198 mm) Item no.
11 Technical Data WP-Ex 3000 II Voltage Power consumption Output Fan capacity WxHxD Weight with motor Sound level Speed Item no.: 146977 110–120 V / 50/60 Hz 5.6 A 650 W 445 m3/h (free-blowing) 680 x 486 (with LED spot + 140 mm) x 527 mm 52 kg ≤ 65 dB (A) 750-6000 min-1 adjustable Other voltages on request. The noise level of the unit amounts to ≤ 65 dB (A). Technical changes reserved. 12 Disposing of the Unit The unit has to be disposed by an authorized recycling operation.
13 EU Declaration of Conformity in accordance with 2014/35/EU (Low Voltage Directive) and 2014/30/EU (Electromagnetic Compatibility Directive) and 2006/42/EC (Machinery Directive) and 2011/65/EU (RoHS Directive) Manufacturer: WASSERMANN Dental-Maschinen GmbH Rudorffweg 15-17 21031 Hamburg Germany Product description: Model: WP-Ex 3000 II 115 V version Applicable standards: DIN EN 61010-1 DIN EN 61000-6-3 DIN EN 61000-6-1 DIN 45635-1 DIN EN 60335-1 Polishing Compact Unit for dental applications Item
Notes: 19
