Configuration Commands CONFIGURATION MANUAL START To begin procedures the configuration END CCD - 80SIR Bar Code Scanner To finish the configuration procedures and save new parameters in memory. ABORT To give up all parameters that you have just selected. 0 12345 67890 5 SET To make all parameters back to default settings with * in this manual.
Configuration Commands Configuration Procedures START START To begin procedures SET Configuration the IMPORTANT NOTICE All Defaults configuration END To finish the configuration procedures and save new parameters in memory. Each standard package contains main unit, interface cable and user's manual. The user's manual gives you an overall review and information about the scanner only. For those who can do the configuration by themselves, please contact your dealer for separate configuration manual.
TABLE OF CONTENTS USER MANUAL 1 CHAPTER 4 OPTIONAL SETTING 26 Using the CCD Scanner 1 4.1 Reading Modes Parameters 26 Installation 3 4.2 Code Mark ( COde I.D.) Parameters 27 General Scanning Tips 4 4.3 Pre-amble and Post-amble 28 Testing the Symbologies 5 General Scanning Tips 6a 4.4 Buzzer Parameters 28 Affixing the CCD stand 6b 4.5 Other Parameters 29 CHAPTER 1 INTRODUCTION 7 1.1 Default Configuration 7 1.2 Custom Configuration 8 1.
1 2 2) CCD-80SIR doesn't have trigger, you may get more USER'S MANUAL easily and no worry about trigger place. BAR CODE SCANNER 3) This is the HARD WAY to get the scanner, we usually do this way while the scanner has trigger. Getting this way working will be tired soon. 0 12345 67890 5 Using the CCD Scanner There are several scanning modes within the CCD scanner for you to choose in order to suit your application. Please refer to the configuration manual for a proper selection.
3 4 Installation General Scanning Tips The CCD scanner can be easily interfaced to a You can optimize performance by changing the keyboard or a serial port to your computer. Now position of the scanner with respect to the barcode follow the procedures below for a proper installation. labels. Please note the help hints below to ensure an effective scanning with the CCD scanner.
5 6a Testing the Symbologies Troubleshooting List If you have installed the CCD scanner, please try to The CCD scanner automatically executes a self-test read when the power is on. If the CCD scanner does not the following barcodes to make sure your scanner is operating properly. read a barcode label, please check the following list first. UPC-A UPC-E ● If the barcode label is smeared or rough. ● If the interface cable is firmly connected. ● If the power is applied.
6b Affixing the CCD stand 6c
7 8 CHAPTER 1 INTRODUCTION This manual provides all useful information regarding configuration, custom configuration and configuration procedure. You are suggested to read all information containing herein before starting to configure your scanner. As stated, we recommend that configuration, especially custom configuration, better to be performed by experienced users, your dealer or your software consultant. 1.
10 9 Important configuration commands: START -Scan START label to initiate your custom Computer Type *PC/AT & PS-50,60,70,80 configuration procedure. ABORT -Scan ABORT label to abadon all parameters PC/XT you have just selected. END - Scan END label to finish the configuration and save the new parameters in memory. IBM5550 EXIT - "EXIT" is specially for ending the setup of PS-55 "Hex-Label" printed in Appendix D.
11 12 5. Keyboard Number Keys 2. Keyboard Speed of PC/AT * Normal * Alphanum Turbo 3. Keyboard Character Delay Min. to Max:(00-99) Define char. delay=?? Numeric Pad 6. Keyboard Data Terminator * CR None Note: For setting up, please refer to the examples in SPACE Chapter 5. TAB 4.
13 14 2.2 RS-232C Parameters The scanner also provides RS-232C interface to meet your application . Scan the label below for RS-232C 1. Baud Rate ( bps) 19200 300 interface. RS - 232C 600 1200 2400 RS-232 Pin Assignment: 4800 DUSB-9P Female 1 N/C (=no connection) 2 TXD 5 GND 7 CTS 8 RTS 9 VCC (+5V) *9600 38400 2. Data Bits * 8 Bits DC Adapter +5v +- 10% 150mA (min.) 7 Bits 3. Parity RS-232C parameters include: 1. Baud rate * None 2. Data bits Odd 3. Parity 4.
15 16 4. Handshaking * None CHAPTER 3 BAR CODE SETTING The scanner can read almost all popular symbologies RTS/CTS in the world. Scan one or more codes from the following labels to meet your applications. Xon/Xoff Readable Code Setting *On Code 39 Off 5. Character Delay Min. to Max.:(00-99) Define char. delay=?? On ITF 2/5 6.
17 18 Readable Code Setting ( Cont'd) *On 3.1 CODE 39 Parameters These parameters include: 1. Character set EAN-13/UPC-A Off 2. Verify check digit 3. Transmit check digit 4. Transmit start/stop digit * On 1. Character Set * Standard Code EAN-8 Off Full ASCII code * On UPC-E 2. Verify Check Digit Off * No On Yes UPC/EAN * Off Add-on 2/5 3. Transmit Check Digit *On Code 128 * Yes No Off On Code 14 4.
19 20 3.2 Interleave 2 of 5 Parameters 3.3. Industrial 2 of 5 Parameters 1. Verify check digit 1. Verify check digit 2. Transmit check digit 2. Transmit check digit 3. Code length 3. Code length 1. Verify Check Digit 1. Verify Check Digit * No * No Yes Yes 2. Transmit Check Digit * No Yes 3. Code Length * Variable length Min.=?? Max.=?? (4 - 48) Fixed length Custom define=??? Note: 1. Default is set to various length with minimum 4 and maximum 48. 2.
21 22 3.4 Matrix 2 of 5 Parameters 3.5 Codabar Parameters 1. Verify check digit 1. Transmit start/stop characters 2. Transmit check digit 2. Type of start/stop characters 3. Code length 1. Verify Check Digit 1. Transmit Start/Stop Characters * No * No Yes Yes 2. Transmit Check Digit * No 2. Type of Start/Stop Characters * abcd/abcd Yes ABCD/ABCD ABCD/TN*E 3.Code Length * Variable length Min.= ?? Max.
23 24 3.6 EAN-13 Parameters 3.7 UPC-A Parameters 1. Transmit first digit 2. Transmit second digit 3. Transmit check digit 1. Transmit first digit 2. Transmit second digit 3. Transmit check digit 1. Transmit First Digit 1. Transmit First Digit * Yes * Yes No 2. Transmit Second Digit No 2. Transmit Second Digit * Yes *Yes No 3. Transmit Check Digit * Yes No 3.
25 26 3.8 EAN-8 Parameters 1. Transmit first digit CHAPTER 4 OPTIONAL SETTING This chapter provides you instructions for selecting optional parameters in order to fit your special 2. Transmit check digit requirements. These options include reading modes, 1. Transmit First Digit * Yes code mark, pre-amble, post-amble, buzzer pitch, buzzer duration, power-up tone, and LED indicator. 4.11 Flash Mode Flash Mode No * Enable Disable 2. Transmit Check Digit * Yes 4.
28 27 4.2 Code Mark ( Code ID) Parameters You may use the example listed below to define the code mark for your own applications. Please note that each code mark you define has to follow the steps as example shown below . You may also refer to Chapter 5 for details. For example: to define " Z " as code mark for code 39. , the steps will be as under : a) Scan " Start " label. b) Scan Code 39 label as below. c) Refer to Appendix A. ASCII Code Table where shows " 5" "A" stand for " Z". d) From Appendix D.
29 30 4.5 Other parameters These parameters include power up tone and LED indicator. Power up Tone * On Please do remember one thing , that is - everytime before setting up your own definition, you will have to write down the order of characters/digits that you find out from ASCII Code Table/Decimal Table first. This important step will minimize mistakes when you proceed Off configuration procedures. Example 1.
31 32 Chapter 6. USB Connection ( Optional) Scan the following command codes to complete USB setting: SET START USB Setting END APPENDICES APPENDIX A.
33 34 APPENDIX B. DECIMAL TABLE H APPENDIX C.
35 36 B) C) Readable Code Keyboard Layout On Switzerland Sweden/Finland Code 93 * Off Italy On Belgium Code 11 * Off U.K.
37 38 D) Code 11 Parameters : 1. Number of Check Digit Yes 3. Transmit Check Digit One No Two G) General Parameters- Code Mark 2. Transmit Check Digit Yes Code Mark Parameters Code 93 Code 11 No MSI/Plessy China Postage E)Code 93 Parameters Concatenation On Code IV Off F) China Postage Parameters 1. Code Length Variable Length Min=? Max=?(2-40) CANCEL Note: 1. Read code type ( just once a time) and then CANCEL label afterwards.
39 APPENDIX D.
