Specifications

23
Gage
Heads
Output cable 2m
Drive unit cable 2m
2-ø4.5, 9 depth 5
RM12BPG-6P (HIROSE)
HR10A-7P-6P (HIROSE)
13
50
-0.013
0
ø20
6
191.5
Stroke 102 or longer
ø6
429
17
49
33
7
36
243.5
68
34
50
36
7
17
20
34
33
ø20
0
-0.013
Output cable 2m
Drive unit cable 2m
2-ø4.5, ø9 depth 4
RM12BPG-6P (HIROSE)
HR10A-7P-6P (HIROSE)
Stroke 102 or longer
Rubber boot
236
67 243.5
473.5
11PRH/12PRH
(Applicable counter depends on the gage)
FEATURES
*1: Excluding quantizing error of ±1 count.
*2: Both the plunge speed and measuring force of the motor-driven type can be varied with the supplied motor drive unit.
*3: IP level is the standard of protection against the ingress of solids/foreign matter and water. This may not be applicable depending on the kind of liquid.
*4: Patent pending (Japan)
Order No. 542-313 542-315 542-333 542-335
Measuring range 100mm
Resolution 0.0001mm 0.001mm
Accuracy (20°C)*
1
(2+L/100)μm ≤ 2.5μm (L=mm) (2.5+L/100)μm ≤ 3μm (L=mm)
Measuring
force
(Approx.)
Spindle DOWN L3 (approx. 3.0N) L4 (approx. 4.5N) L3 (approx. 3.0N) L4 (approx. 4.5N)
Horizontal L7 (approx. 6.5N) Not available L7 (approx. 6.5N) Not available
Spindle UP H4 (approx. 9.5N) L9 (approx. 6.0N) H4 (approx. 9.5N) L9 (approx. 6.0N)
Position-detection method Reflection-type photoelectric linear encoder
Response speed*
2
400mm/s 800mm/s
Output signal 90° phase difference, differential square wave (RS-422A equivalent)
Signal pitch 4
μm
Mass Approx. 940g Approx. 970g Approx. 940g Approx. 970g
Dust/water protection*
3
IP54 IP66 IP54 IP66
Spindle-sealing method Scraper Rubber boot Scraper Rubber boot
Contact point Sø3mm carbide (mounting: M2.5x0.45), 901312
Stem size ø20mm
Spindle-drive method Electric motor
Bearing type Linear ball bearing*
4
Resistance to impact 60g (According to Mitutoyo's internal tests)
Connecting cable length 2m
Connector
types
Data output
Plug used: RM12BPE-6PH (HIROSE), Compatible socket: RM12BRD-6S (HIROSE)
Gage control
Plug used: HR10A-7P-6P (HIROSE), Compatible socket: HR10A-7P-6P (HIROSE)
External control
Plug used: HR10A-10R-10S (HIROSE), Compatible socket: HR10A-10R-10P (HIROSE)
Operating environment 0°C to 40°C (20%RH to 80%RH, without condensation)
Standard accessories
Wrench for contact point (210187), hex-head bolt (M4x0.7x35, 2pcs.), washer (M4, 2pcs.)
Optional accessory
—
02ADA004:
Rubber boot (spare)
—
02ADA004:
Rubber boot (spare)
SPECIFICATIONS
Dimensions
Unit: mm
Motor Drive Unit
(provided as standard)
FEATURES
Controls spindle extension/
retraction of motor-driven type
gage heads.
• Measuring force: Can be set
appropriately with the rotary switch
on the main unit (to one of the
combinations of H/L and a number
between 0 and 9) depending on the
mounting position.
•
Dimensions (WxDxH): 90x175x74mm
(without rubber boot)
•
Input signal: Spindle extend / Spindle
retract
•
Output signal: Spindle stopped at
upper limit of travel
•
Mass: Approx. 830g
• Power supply: AC100 to 240V
ø18
41
ø11.8
Unit: mm
Connector
542-313: 0.1
μm resolution model
542-333: 1μm resolution model
542-315: 0.1μm resolution, rubber boot model
542-335: 1μm resolution, rubber boot model
LGM Motor-drive, Long Stroke Type
100mm range, 0.1 / 1µm resolution, Differential square-wave output
FEATURES
• There are three types including the standard model, low measuring force model, and rubber boot model
(“made to order” basis) available.
•
The resolution of each model can be selected to be 0.1μm or 1μm.