Specifications

22
Gage
Heads
RM12BPG-6P (HIROSE)
Connecting Cable 2m
2-ø4.5, ø9 depth 5
33
17
20
ø6
49
50
13
429
Stroke 102 or longer
191.5
6
-0.013
0
ø20
7
36
243.5
68
34
2-ø4.5, ø9 depth 4
49 33
34
17
ø20
7
20
Stroke 102 or longer
Rubber boot
67
236
243.5
473.5
RM12BPG-6P (HIROSE)
11PRH/12PRH (Compatible counter depends on the gage)
Connecting cable 2m
50
36
6
0
-0.013
FEATURES
*1: Excluding quantizing error of ±1 count.
*2: Note that an over-speed error may occur if the contact point is released quickly after it has been pressed in, depending on the amount of over-travel produced.
*3: IP level is the standard of protection against the ingress of solids/foreign matter and water. This may not be applicable for liquids other than water.
*4: Patent pending (Japan)
Order No. 542-312 542-316 542-314 542-332 542-336 542-334
Measuring range 100mm
Resolution 0.0001mm 0.001mm
Accuracy (20°C)*
1
(2+L/100)μm ≤ 2.5μm (L=mm) (2.5+L/100)μm ≤ 3μm (L=mm)
Measuring
force
(Approx.)
Spindle DOWN 8.0N or less 3.0N or less 8.0N or less 8.0N or less 3.0N or less 8.0N or less
Horizontal 6.5N or less Not available 6.5N or less 6.5N or less Not available 6.5N or less
Spindle UP 5.0N or less Not available 5.0N or less 5.0N or less Not available 5.0N or less
Position-detection method Reflection-type photoelectric linear encoder
Max. response speed*
2
400mm/s 800mm/s
Output signal 90° phase difference, differential square wave (RS-422A equivalent)
Signal pitch 4
μm
Mass Approx. 750g Approx. 780g Approx. 750g Approx. 780g
Dust/water protection*
3
IP54 IP66 IP54 IP66
Sealed-spindlle method Scraper type Rubber boot type Scraper type Rubber boot type
Contact point ø3mm carbide (mounting: M2.5x0.45), 901312
Stem size ø20mm
Bearing type Linear ball bearing*
4
Resistance to impact 60g (According to Mitutoyo's internal tests)
Connecting cable length 2m
Connector
Plug used: RM12BPE-6PH (HIROSE), Compatible socket: RM12BRD-6S (HIROSE)
Operating environment 0°C to 40°C (20%RH to 80%RH, without condensation)
Standard accessories
Wrench for contact point (210187), hex-head bolt (M4x0.7x35, 2pcs.), washer (M4, 2pcs.), lifting lever (137693), lever holder (02ADG181)
Optional accessory
—
02ADA004:
Rubber boot (spare)
—
02ADA004:
Rubber boot (spare)
SPECIFICATIONS
Dimensions
Unit: mm
Lifting lever
LG Long Stroke Type
100mm range, 0.1 / 1µm resolution, Differential square-wave output
FEATURES
• There are three types including the standard model, low measuring force model, and rubber boot model
(“made to order” basis) available.
•
The resolution of each model can be selected to be 0.1μm or 1μm.
ø18
41
ø11.8
Unit: mm
Connector
542-312: 0.1μm resolution model
542-316: 0.1μm resolution, low measuring force model
542-332: 1μm resolution model
542-336: 1μm resolution, low measuring force model
542-314: 0.1μm resolution, rubber boot model
542-334: 1μm resolution, rubber boot model