Warranty

1.
2. Align two screw bosses and boss holes on back of two halves of base according to Figure 2.
3. Press two halves of the base, as in Figure 3, to interlock them together. (Figure 3)
4. Align power cord to the slot on the top side of the base. (Figure 4)
. 5
Unscrew three (3) locking screws from the bottom of the heater body (Figure 1) and save them.
ASSEMBLY INSTRUCTIONS
Parts of the Heater Symbols
Power Button
H/L Heat Button
Oscillation Button
Plus Button
Minus Button
Timer Button
PARTS OF THE HEATER
1. Control Panel
2. LED Display
3. Safety Grille
4. Base
5. Remote Control
6. Power Light
1
6
3
4
5
2
Figure 4
Figure 5
Temperature Setting Button
Secure the base to the heater body with the locking screws from Figure 1. Tighten the locking screws
firmly with a screw driver. (Figure 5)
1.
OPERATING INSTRUCTIONS
Operation
Place the heater on a firm, level surface, after assembling per this manual. Plastic or rubber tabs, like the feet on
this unit, may stick to furniture surfaces and/or hardwood floors. The unit may leave a residue that could darken,
stain or leave permanent blemishes on the finish of certain furniture surfaces, including wood surfaces, and/or
hardwood floors.
3.
4. Turn the heater ON by pressing the
Power Button .
Pressing the
Oscillation Button
will allow the heater to oscillate back and forth. To stop the oscillation,
press the
Oscillation Button again.
Oscillation
3. When the heater is initially plugged in, there will be a "beep" and the
Power Light will turn on indicating
power to the unit. The
Power Light will remain lit until the heater is unplugged from the electrical outlet.
When the display shows the temperature at which you want to set the unit, the set temperature will flash
several time. The display will return to indicate the current room temperature and will gradually change as the
room temperature changes.
2.
Plug the cord set into a 120 volts AC outlet. Be sure that the plug fits tightly into outlet. When plugs fit loosely
into receptacles, they may slip partially or completely out of the receptable with only the slight movement of the
attached cord. Receptables in this condition may overheat and pose a serious fire hazard; if covered by a curtain
or drape, the fire hazard is even greater.
reading in Celsius. Press the same two buttons together again to change the display back to show the
temperature reading in Fahrenheit.
2. Press the and buttons at the same time for two seconds to change the display to show the temperature
5. When turning the heater on, the unit will be in HIGH heat.
6. Press the button to switch over LOW or HIGH heat.
7. To turn the heater OFF, press the
Power Button . The unit will first turn off the heating elements, the fan
r the fanetfa ylno teltuo lacirtcele eht morf gulp eht gnillup yb tinu eht gulpnU .retal sdnoces 03 nwod tuhslliw
stopped.
Timer Function
The timer function may be activated when the heater display is in any function. This function allows you to set
the length of time the heater will run before turning itself off, from 0 hour to 8 hours. Pressing the
Timer Button
will increase the length of time by 1 hour each time this button is pressed. After the display reflects 8 hours, pressing
the
nottuB r emiT once more will reset the heater to run continuously. The heater will turn off when the set time
has el
to 0 hour will cancel the timer function.
apsed. The unit can be turned back on by pressing the
Power Button . Pressing the Timer Button
1.
Automatic Temperature Control
To set the room at a specific temperature, press the Temperature Setting Button , then press the
or buttons to the desired temperature. The heater is now in Auto Temperature Mode and the indicator will
glow on the LED display.
A
Figure 1 Figure 2 Figure 3
Screw Bosses
Boss Holes