Specifications

8 9
RESTORING FACTORY-SET BEVERAGE STATIONS
1. To restore factory-set default beverage stations, press both
Speed Up
and Speed Down buttons. LCD will prompt ADD NEW
PROGRAM.
2. Press
button.LCDwillpromptRESTOREDEFAULTPROGRAMS.
3. Press
button to confirm and save. The LCD will display the logo for
3 seconds.
4. The unit will return to standby mode and the LCD will prompt PRESS
ANYBUTTONTOBLEND.
NOTE: The Stop
key will abort this process at any point before
restoring default programs is confirmed.
DRINK COUNTER
Your reprogrammable blenders are equipped with a drink counter to keep
track of daily drink totals and total drink counts for your machine. To display
the counts, hold program buttons
& simultaneously for 3 seconds.
Your display will read:
DAILYCOUNTXXXX
TTLCOUNTXXXXX
DailyCountwilldisplaythenumbersofdrinksmixedperday.TotalCount
is the accumulation of all drinks made since first use of the blender.
The Daily Count can be reset by holding in program buttons
&
simultaneouslyfor3secondsthen,pressing(ON/OFF)buttonfor3seconds.
DailyCountwillresettozeroandTotalCountwillremainunchanged.
IfTotalCountneedstobereset,callyournearestWaringauthorizedservice
facility for information.
NOTE: Use of the PULSE features will not add to the daily or total drink
counts.
RESETTING THERMAL PROTECTION
• Yourblenderisequippedwithanautomaticresetfunctiontoprotectthe
motor from overheating.
• Ifyoublenderstopsrunningunderheavyuse,turnthepowerswitchto
 Offandunplugthepowercord.Emptytheblendercontainerofall
its contents and allow between 5 and 30 minutes for the motor to
cool down.
• Plugthepowercordbackintotheoutletandcontinueblending.
• Ifyourblenderdoesnotfunctionproperlyfollowingthisprocedure,
discontinue use and contact a certified Waring Customer Service Center.
IMPORTANT - HOT BLENDING INSTRUCTIONS
Tominimizethepossibilityofbeingscaldedwhenblendinghotmaterials,
the following precautions and procedure must be observed.
• Hotmaterialsarethosethatare100°F(38°C)orhotter.
• Limittheamountofmaterialsprocessedto1pint.
• Completelyremovethecenterportionofthetwo-piececontainerlidbefore
startingmotor(thiswillallowventingoftherapidlyheatedandexpanded
air inside the container when blender is running).
• Alwaysstartblendingonlowestspeedsetting,andthenprogressto
desired speed.
• Neverstanddirectlyoverblenderwhenitisbeingstartedorwhileit
is running.
SOUND ENCLOSURE (for MX1500XTX Version)
YourMX1500XTX/MX1500XTP/MX1500XTSblenderisequippedwitha
heavy-duty polycarbonate sound enclosure to reduce noise level while
blending. This sound enclosure is removable and dishwasher safe.
To remove the sound enclosure, follow these steps:
 1. Opensoundenclosureandremoveblendercontainer.
2. Remove front portion of sound enclosure by disengaging both sides at
the pivot point.
3. Remove rubber jar pad.
4. Remove 3 screws from blender base and remove sound enclosure.
NOTE: To replace sound enclosure, follow above steps in reverse.
TURNING OFF YOUR BLENDER
Whether your blender is in standby mode, new programming mode, or
themotorisrunning,pressingtheOn/Off
button will stop the unit
from running and will turn the power off. The LCD display will turn off.
NOTE:Allprogramsandcurrentsettingswillberestorednexttimeyou
turn unit on.
CLEANING AND SANITIZING INSTRUCTIONS
THEBLENDERCONTAINERMUSTBECLEANEDANDDRIEDAFTEREACH
USEACCORDINGTOTHEFOLLOWINGINSTRUCTIONS.FAILURETODO
SOMAYALLOWRESIDUESOFPROCESSEDMATERIALTOCOLLECTON
THEINTERNALSEALSOFTHEBLADEASSEMBLY,RENDERINGTHEM
INEFFECTIVE.
• Wash,rinse,sanitizeanddrycontainerpriortoinitialuseandwheneverit
will not be used again within a period of one hour.
• Washandrinsecontaineraftereachuse.