Specifications

6 7
button to adjust the blending speed. The LCD will show the setting
speed and motor speed will change.
  NOTE:Thespeedcanbesetfrom15%to100%.Oncethe
Pulse
button is released, the motor will shut off and the blender will to return
to standby mode. The changed pulse speed will be stored in memory to
replace the default speed at 100%.
REPROGRAMMABLE STATIONS
 1. Thereare4ProgramButtonsforfourreprogrammablebeveragestations
for easy operation and consistent results. The factory-set stations are
programmed as listed below:
Liquid drinks
Frozendrinks
Icecreamdrinks
Smoothies
2. To run any of the above preset programs, blender must be in
standby mode.
3. Press desired Program button to start the blender. The motor will run at
the pre-set speed within the preset blending time. The LCD will show time
remaining.Oncetheblendercountsdownto0,themotorwillstop
running and the blender will return to standby mode and prompt
PRESSANYBUTTONTOBLEND.
NOTE:Toterminateablendingprogram,simplypressStart/Stop
button or any of the program buttons. After doing this, the blender will
returntostandbymodeandLCDwillpromptPRESSANYBUTTON
TOBLEND.
REPROGRAMMING BEVERAGE STATIONS
Users can add 4 new programs to meet their needs. A program can
consist of several sections, each with a different speed and running time.
Forexample,
can be replaced with a new program that has 3 sections,
as shown below:
Section 1: speed = 75%, time = 30 seconds
Section 2: speed = 100%, time = 20 seconds
Section 3: speed = 50%, time = 20 seconds
The program has the following limitations:
Speed: 15% to 100%
Time: 5 to 90 seconds
 Totalrunningtimeinaprogramcannotexceed90seconds,i.e.,sum
of the Sections cannot be longer than 90 seconds.
NOTE: The
buttonwillactastheenterkeytoproceedtonextstep
during the reprogramming process.
1. To enter new program, press both Speed Up
and Speed Down
buttons simultaneously while unit is in standby mode. The blender will
enter new programming mode and the LCD will prompt ADD NEW
PROGRAM.
 2. Next,youwillneedtosetvalues.PresstheProgrambuttonyouwant
toreplace(i.e.,1...4).TheLCDwillpromptUSEUP/DOWNTOSET
SPEED: 25%.
NOTE: 25% is the default speed setting in the reprogramming mode.
3. Press Speed Up
or Speed Down button to set the speed value.
The increment is 1% (150 RPMs). Press and hold the button to quickly
scroll through speeds. The speed can be set between 15% and 100%.
 4. Oncerequiredspeedisreached,press
button or wait 5 seconds
toconfirmsetting.TheLCDwillnowpromptUSEUP/DOWNTOSET
TIME5.NOTE:Fivesecondsisthedefaulttimesettinginthe
reprogramming mode.
5. Use Speed Up or Speed Down button to set the time value (up
to90seconds).Oncethe90secondsisreached,pressingSpeedUp
willnotincreasethevalueandtheLCDwillpromptMEMORYLIMITfor
2 seconds.
6. Press button or wait 5 seconds to confirm the setting. When the
blendingtimeisconfirmed,theLCDwillpromptSELECTANOTHER
SPEED. Repeat steps 3-5 if additional processing is needed.
NOTE: When pressing Speed Up
or Speed Down buttons to set
speedfornextsection,theLCDwillpromptUSEUP&DOWNTOSET
SPEED: 25%.
7. To save the new program settings, press both Speed Up and Speed
Down buttonssimultaneously.TheLCDwillpromptNEWPROGRAM
(PROG#)SAVEDfor5seconds.Theblenderwillreturntostandbymode
andtheLCDwillpromptPRESSANYBUTTONTOBLEND.
NOTE:Ifnobuttonispressedfor60secondswhenpromptedtoADD
NEWPROGRAM,theblenderwillexitnewprogrammingmodeandwill
return to standby mode. The new program will not be stored.
 8. Torunnewprograms,simplypressthedesiredProgrambuttonandthe
blender will run the program set by the user. The LCD will display NEW
PROGRAM#andwillcountdownthesettime.