Brochure

ManualsBrandsWard ManualsCast Iron Fittings6" Black Cast Iron Steam Tee

Summary of content (82 pages)

PAGE 1
PAGE 2
Ward’s mission is profitable growth by exceeding customer expectations through innovation, quality and commitment.
PAGE 3
TABLE OF CONTENTS SECTION 1 Standard Malleable Fittings Class 150.................................................................................................................................................. Pgs. 6 – 16 SECTION 2 Extra Heavy Malleable Fittings Class 300............................................................................................................................................. Pgs. 17 – 22 SECTION 3 Quality Pipe Unions Class 150, Class 250, Class 300, Brass-to-Brass......
PAGE 4
THE WARD STORY Ward Manufacturing, LLC was founded in Blossburg, PA by Mr. Joseph P. Ward in 1924. Beginning in a modest fashion with approximately thirty employees, a small line of cast iron steam and drainage fittings were manufactured along with cast iron plugs and bushings. In the following four years a rapidly increasing demand for Ward products was experienced.
PAGE 5
SECTION 1 Standard Malleable Pipe Fittings Class 150 Ward Class 150 Malleable Iron Fittings are made with the most sophisticated metallurgical and processing controls available. Iron samples are continuously analyzed using spectroscopy to conform the material quality. This sophisticated chemical analysis is complemented by rigorous quality control of incoming raw materials and iron processing.
PAGE 6
MALLEABLE IRON 90 ˚ STRAIGHT ELL CLASS 150 NPS Center to End A 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 0.69 0.81 0.95 1.12 1.31 1.50 1.75 1.94 2.25 2.70 3.08 — 3.79 — 5.13 Outside Dia. of Band B (min) 0.69 0.84 1.01 1.20 1.46 1.77 2.15 2.43 2.96 3.59 4.28 — 5.40 — 7.77 Length of Threads C (min) Take Out 0.25 0.32 0.36 0.43 0.50 0.58 0.67 0.70 0.75 0.92 0.98 — 1.08 — 1.28 0.42 0.40 0.54 0.58 0.76 0.81 1.04 1.21 1.49 1.56 1.88 — 2.49 — 3.
PAGE 7
MALLEABLE IRON 45 ˚ ELL CLASS 150 NPS Center to End A Outside Dia. of Band B Length of Threads C (min) Take Out 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 5 6 0.73 0.73 0.80 0.88 0.98 1.12 1.29 1.43 1.68 1.95 2.17 2.61 — — 0.69 0.84 1.01 1.20 1.46 1.77 2.15 2.43 2.96 3.59 4.28 5.40 — — 0.25 0.32 0.36 0.43 0.50 0.58 0.67 0.70 0.75 0.92 0.98 1.08 — — 0.46 0.32 0.39 0.34 0.43 0.43 0.58 0.70 0.92 0.81 0.97 1.31 — — A A C B MALLEABLE IRON 90 ˚ STREET ELL CLASS 150 Outside Port Dia. Dia.
PAGE 8
MALLEABLE IRON STREET 45 ˚ ELL CLASS 150 Outside Port Dia. Dia. of Male Band End C (min) D (max) Length of Internal Threads E (min) Length of External Threads F (min) Take Out Male End Take Out Female End 0.20 0.25 0.26 0.67 0.42 0.84 0.26 0.32 0.40 0.53 0.32 1.03 1.01 0.37 0.36 0.41 0.62 0.39 0.88 1.15 1.20 0.51 0.43 0.53 0.61 0.34 3/4 0.98 1.29 1.46 0.69 0.50 0.55 0.74 0.43 NPS Center to End A Center to Male B 1/8 0.69 0.94 0.69 1/4 0.73 0.94 3/8 0.
PAGE 9
MALLEABLE IRON REDUCING TEES CLASS 150 NPS 1/4 x 1/4 x 1/8 1/8 x 1/8 x 1/4 3/8 x 3/8 x 1/4 3/8 x 1/4 x 3/8 3/8 x 1/4 x 1/4 1/4 x 1/4 x 3/8 1/2 x 1/2 x 3/8 1/2 x 1/2 x 1/4 1/2 x 3/8 x 1/2 1/2 x 3/8 x 3/8 1/2 x 1/4 x 1/2 3/8 x 3/8 x 1/2 3/4 x 3/4 x 1/2 3/4 x 3/4 x 3/8 3/4 x 3/4 x 1/4 3/4 x 1/2 x 3/4 3/4 x 1/2 x 1/2 3/4 x 3/8 x 3/4 3/4 x 3/8 x 3/8 3/4 x 1/4 x 3/4 1/2 x 1/2 x 3/4 1 x 1 x 3/4 1 x 1 x 1/2 1 x 1 x 3/8 1 X 1 X 1/4 1 x 3/4 x 1 1 x 3/4 x 3/4 1 x 3/4 x 1/2 1 x 1/2 x 1 1 x 1/2 x 3/4 1 x 1/2 x 1/2 1 x 3
PAGE 10
NPS 1 1/2 x 1 x 1 1/2 1 1/2 x 1 x 1 1/4 1 1/2 x 1 x 1 1 1/2 x 3/4 x 1 1/2 *1 1/2 x 3/4 x 3/4 1 1/2 x 1/2 x 1 1/2 1 1/4 x 1 1/4 x 1 1/2 1 x 1 x 1 1/2 2 x 2 x 1 1/2 2 x 2 x 1 1/4 2x2x1 2 x 2 x 3/4 2 x 2 x 1/2 2 x 1 1/2 x 2 2 x 1 1/2 x 1 1/2 2 x 1 1/2 x 1 1/4 2 x 1 1/2 x 1 2 x 1 1/4 x 2 2 X 1 1/4 X 1 1/2 2 x 1 1/4 x 1 1/4 2x1x2 *2 x 1 x 1 2 x 3/4 x 2 2 x 1/2 x 2 1 1/2 x 1 1/2 x 2 1 1/4 x 1 1/4 x 2 1x1x2 2 1/2 x 2 1/2 x 2 2 1/2 x 2 1/2 x 1 1/2 2 1/2 x 2 1/2 x 1 1/4 2 1/2 x 2 1/2 x 1 2 1/2 x 2 1/2 x 3/4 2 1/2 x
PAGE 11
MALLEABLE IRON PIPE CAPS CLASS 150 Overall Height A (min) Outside Dia. of Band B (min) Length of Threads C (min) *1/8 +1/4 +3/8 0.53 0.63 0.74 0.56 0.84 1.01 0.25 0.32 0.36 +1/2 +3/4 1 1 1/4 1 /2 2 2 1/2 3 3 1/2 4 5 6 8 0.87 0.97 1.16 1.28 1.33 1.45 1.70 1.80 — 2.08 — — — 1.20 1.46 1.770 2.15 2.43 3.00 3.59 4.28 — 5.40 — — — 0.43 0.50 0.58 0.67 0.70 0.75 0.92 0.98 — 1.
PAGE 12
MALLEABLE IRON STREET TEES CLASS 150 NPS 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 *1 1/4 x 1 x 1 1/4 Center to End A Center to Male B — — — 1.31 1.50 1.75 1.94 2.25 1.75 — — — 1.89 2.14 2.45 2.69 3.26 2.45 Outside Port Dia. Length of Length of Dia. of Male Internal External Band End Thread E Thread F C (min) D (max) (min) (min) — — — 1.46 1.77 2.15 2.43 2.96 2.15 — — — 0.69 0.91 1.19 1.39 1.79 0.91 — — — 0.50 0.58 0.67 0.70 0.75 0.67 — — — 0.55 0.68 0.71 0.72 0.76 0.
PAGE 13
MALLEABLE IRON REDUCING COUPLING CLASS 150 Outside Outside Length of Dia. Dia. Threads Small Large Small End Band Band B (min) B2 (min) C (min) Length of Threads Large End C2 (min) NPS Length of Coupling A 1/4 x 1/8 3/8 x 1/4 3/8 x 1/8 1/2 x 3/8 1/2 x 1/4 1/2 x 1/8 3/4 x 1/2 3/4 x 3/8 3/4 x 1/4 3/4 x 1/8 1 x 3/4 1 x 1/2 1.00 1.13 1.13 1.25 1.25 1.25 1.44 1.44 1.44 1.44 1.69 1.69 0.69 0.84 0.69 1.01 0.84 0.69 1.20 1.01 0.84 0.69 1.46 1.20 0.84 1.01 1.01 1.20 1.20 1.20 1.46 1.46 1.46 1.46 1.77 1.77 0.
PAGE 14
MALLEABLE IRON EXTENSION PIECES CLASS 150 NPS Overall Length A Length of Length of Internal External Threads Threads B (min) C (min) Take Out Female End Take Out Male End *3/8 *1/2 *3/4 1.50 1.95 2.06 0.36 0.43 0.50 0.40 0.53 0.54 1.09 1.41 1.51 1.09 1.41 1.51 *1 *1 1/4 *2 2.23 2.56 — 0.58 0.67 — 0.68 0.63 — 1.54 1.85 — 1.54 1.85 —    * Manufactured to WARD specifications MALLEABLE IRON LOCKNUTS CLASS 150 NPS +1/8 +1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 Overall Height A 0.19 0.25 0.28 0.
PAGE 15
MALLEABLE IRON CROSS CLASS 150 NPS 1/8 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 Center to End A Outside Dia. of Band B (min) Length of Threads C (min) Take Out — 0.81 0.95 1.12 1.31 1.50 1.75 1.94 2.25 — — — — 0.84 1.01 1.20 1.46 1.77 2.15 2.43 2.96 — — — — 0.32 0.36 0.43 0.50 0.58 0.67 0.70 0.75 — — — — 0.40 0.54 0.58 0.76 0.81 1.04 1.21 1.49 — — — A A A A C B MALLEABLE IRON 45˚ Y CLASS 150 Outside Length of Dia.
PAGE 16
SECTION 2 Extra Heavy Malleable Pipe Fittings Class 300 - (A.A.R.) Ward Class 300 Malleable Iron Fittings are designed to handle higher pressures and more rugged service than our Class 150 fittings. Like all of Ward’s fittings, Class 300 fittings are made with the most sophisticated metallurgical and processing controls available. Ward’s quality assurance program ensures that the iron is made with high quality raw materials and processed according to rigorous standards.
PAGE 17
MALLEABLE IRON 90 ˚ STRAIGHT ELL CLASS 300 Outside Length of Dia. of Threads Band C (min) B (min) Center to End A NPS 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 0.94 1.06 1.25 1.44 1.63 1.94 2.13 2.50 2.94 3.38 — 0.93 1.12 1.34 1.63 1.95 2.39 2.68 3.28 3.86 4.62 — 0.43 0.47 0.57 0.64 0.75 0.84 0.87 1.00 1.17 1.23 — Take Out A C 0.53 0.65 0.71 0.89 0.94 1.23 1.40 1.74 1.80 2.
PAGE 18
MALLEABLE IRON 45 ˚ ELL CLASS 300 NPS 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 4 Center to End A 0.81 0.88 1.00 1.13 1.31 1.50 1.69 2.00 — — — Outside Length of Dia. of Threads C Band (min) B (min) 0.93 1.12 1.34 1.63 1.95 2.39 2.68 3.28 — — — 0.43 0.47 0.57 0.64 0.75 0.84 0.87 1.00 — — — Take Out A 0.40 0.47 0.46 0.58 0.62 0.79 0.96 1.24 — — — C B A H H MALLEABLE IRON 45 ˚ STREET ELL CLASS 300 NPS — — — 2.13 — — — — — 2.39 — — — — — 1.16 — — — — — 0.
PAGE 19
MALLEABLE IRON REDUCING TEES CLASS 300 NPS 3/4 x 3/4 x 1/2 3/4 x 3/4 x 3/8 3/4 x 3/4 x 1/4 3/4 x 1/2 x 3/4 3/4 x 1/2 x 1/2 1 x 1 x 3/4 1 x 1 x 1/2 1 x 1 x 1/4 1 x 3/4 x 1 1 x 3/4 x 3/4 1 x 1/2 x 1 1 1/4 x 1 1/4 x 1 1 1/4 x 1 1/4 x 3/4 1 1/4 x 1 1/4 x 1/2 1 1/4 x 1 x 1 1 1/2 x 1 1/2 x 1 1/4 1 1/2 x 1 1/2 x 1 1 1/2 x 1 1/2 x 3/4 1 1/2 x 1 1/2 x 1/2 2 x 2 x 1 1/2 2 x 2 x 1 1/4 2x2x1 2 x 2 x 3/4 2 x 2 x1/2 2 x 1 1/2 x 2 2 1/2 x 2 1/2 x 2 2 1/2 x 2 1/2 x 1 1/2 3x3x2 Center Center Center to End to End to End A
PAGE 20
MALLEABLE IRON STRAIGHT COUPLING CLASS 300 NPS Length of Coupling A (min) Outside Length of Dia. of Threads Band C (min) B (min) Take Out 1/4 1.37 0.93 0.43 0.28 3/8 1.62 1.12 0.47 0.40 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 1.87 2.12 2.37 2.87 2.87 3.62 — — 1.34 1.63 1.95 2.39 2.68 3.28 — — 0.57 0.64 0.75 0.84 0.87 1.00 — — 0.40 0.51 0.50 0.73 0.71 1.
PAGE 21
MALLEABLE IRON PIPE CAPS CLASS 300 NPS 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 Overall Height A 0.78 0.83 0.98 1.08 1.26 1.38 1.43 1.68 — — Outside Length of Dia. of Threads Band C (min) B (min) 0.93 1.12 1.34 1.63 1.95 2.39 2.68 3.28 — — 0.43 0.47 0.57 0.64 0.75 0.84 0.87 1.00 — —    MALLEABLE IRON CROSS CLASS 300 NPS 1/4 1/2 3/4 1 1 1/4 1 1/2 2 22 Center to End A (min) — 1.25 1.44 1.63 1.94 2.13 2.50 Outside Length of Dia. of Threads Band C (min) B (min) — 1.34 1.63 1.95 2.39 2.68 3.28 — 0.
PAGE 22
WARD UNIONS Rugged-Strong Made of the Best Quality Malleable Iron Extra heavy brass seat ring accurately machined to insure perfect seating under difficult conditions. • Suitably Chamfered • Rust Resistant Treatment • Properly Threaded Continuous, careful inspection during each manufacturing operation.
PAGE 23
SECTION 3 QUALITY PIPE UNIONS Throughout the entire manufacturing process of WARD unions, special emphasis is placed upon the control and accuracy of each operation. WARD unions are made from closely grained, high tensile iron and are produced under expert laboratory supervision. Modern methods of foundry practice and carefully supervised molding are combined to produce castings that are smooth and clean in every respect and free from imperfection.
PAGE 24
WARD UNION BRASS TO IRON SEAT CLASS 150 NPS Overall Length A (min) 1/8 1/4 3/8 1/2 3/4 3/4 X 1/2 1 1 1/4 1 1/2 2 2 1/2 3 *4 1.26 1.44 1.61 1.72 1.94 1.94 2.06 2.26 2.41 2.75 3.22 3.50 3.85 Length of Thru Threads Hole B (min) C (min) 0.30 0.32 0.36 0.43 0.50 0.50 0.58 0.67 0.70 0.75 0.92 0.98 1.08 0.21 0.36 0.52 0.61 0.80 0.80 1.00 1.31 1.55 2.03 2.38 3.00 4.03 Width of Nut D (min) 0.93 1.10 1.26 1.45 1.71 1.71 2.07 2.50 2.82 3.41 4.12 4.75 6.
PAGE 25
WARD UNION IRON TO IRON SEAT CLASS 150 NPS Overall Length A (min) Length of Threads B (min) Thru Hole C (min) Width of Nut D (min) 1/8 1.26 0.30 0.21 1.00 1/4 1.44 0.32 0.36 1.25 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 1.61 1.72 1.94 2.06 2.26 2.41 2.75 3.22 3.50 0.36 0.43 0.50 0.58 0.67 0.70 0.75 0.92 0.98 0.52 0.61 0.80 1.00 1.31 1.55 2.03 2.38 3.00 1.50 1.68 2.00 2.25 2.81 3.06 3.68 4.68 5.18 C B A B D H H Section 3 Page 23 Ward Union Iron to Iron,Class 150 X.
PAGE 26
WARD DI-ELECTRIC UNION IRON TO BRASS NPS Overall Length A (min) Length of Threads B (min) Thru Hole C (min) Width of Nut D (min) *1/2 x 1/2 1.87 0.57 0.54 1.68 *3/4 x 1/2 1.87 0.64 0.74 1.68 *3/4 x 3/4 1.31 0.64 0.74 1.68 C * Manufactured to WARD specifications H H A B D WARD UNION BRASS TO BRASS SEAT CLASS 300 NPS Overall Length A (min) Length of Threads B (min) Thru Hole C (min) Width of Nut D (min) 1/4 1.55 0.43 0.30 1.33 3/8 1.71 0.47 0.42 1.
PAGE 27
SECTION 4 PLUGS AND BUSHINGS PLUGS NPS Thread Length A (min) 1/8 0.37 1/4 0.44 3/8 0.48 1/2 0.56 3/4 0.63 1 0.75 1 1/4 0.80 1 1/2 0.83 2 0.88 2 1/2 1.07 3 1.13 3 1/2 1.18 4 1.22 5 1.31 6 1.40 8 1.57 10 WARD Plugs and Bushings are produced in both Malleable Iron and Cast Iron grades. The iron from which they are made is held to strict formula by careful chemical analysis and control. Tapping is done on the most modern type of threading machines.
PAGE 28
CAST IRON SOLID PLUGS CLASS 125 NPS Nominal Width Across Flats A Distance Between Lugs B (min) Length of Threads C (min) Height of Square D (min) *1/8 9/32 — 0.37 0.24 *1/4 3/8 — 0.44 0.28 *1/2 9/16 — 0.56 0.38 *3/4 5/8 — 0.63 0.44 *3/8 7/16 0.48 0.31 1 13/16 — 0.75 0.50 1 1/4 15/16 — 0.80 0.56 1 1/2 1 1/8 — 0.83 0.62 2 1 5/16 — 0.88 0.68 2 1/2 1 1/2 — 1.07 0.74 3 1 11/16 — 1.13 0.80 3 1/2 — — — — +4 — 7/8 1.22 1.00 +5 — 7/8 1.31 1.
PAGE 29
COUNTERSUNK PLUGS CLASS 125 AND 150 NPS Nominal Size of Square A Length of Threads B (min) +1/4 1/4 0.44 +3/8 5/16 0.48 1/2 3/8 0.56 3/4 1/2 0.63 1 1/2 0.75 1 1/4 3/4 0.80 1 1/2 3/4 0.83 2 7/8 0.88 2 1/2 1 1/8 1.07 3 1 3/8 1.13 3 1/2 1 1/2 1.18 A B B +Steel CAST IRON HEX HEAD CLEANOUT PLUGS CLASS 125 NPS Overall Height A Length of Threads B (min) Nominal Width Across Flats C 1 1/4 1.03 0.53 1.01 1 1/2 1.02 0.52 1.01 2 1/2 1.25 0.62 1.20 3 1.37 0.
PAGE 30
CAST IRON HEXAGON BUSHINGS CLASS 125 NPS Width of Head A Height of Head B Length of External Threads C (min) Length of Internal Threads D (min) Inside or Outside Head 1 1/4 x 3/4 1.76 0.28 0.80 0.50 Outside 1 1/4 x 1/2 1.34 0.34 0.80 0.43 Inside 1 1/4 x 3/8 1.12 0.34 0.80 0.36 Inside 1 1/4 x 1/4 1.12 0.34 0.80 0.32 Inside *1 1/4 x 1/8 1.12 0.34 0.80 0.32 Inside 1 1/2 x 1 2.00 0.31 0.83 0.58 Outside 1 1/2 x 3/4 1.63 0.37 0.83 0.50 Inside 1 1/2 x 1/2 1.34 0.
PAGE 31
CAST IRON HEXAGON BUSHINGS CLASS 125 NPS Width of Head A Height of Head B Length of External Threads C (min) Length of Internal Threads D (min) Inside or Outside Head 3 1/2 x 1 1/2 — — — — Inside 3 1/2 x 1 1/4 2.39 0.52 1.18 0.67 Inside 3 1/2 x 1 1.95 0.52 1.18 0.58 Inside *3 1/2 x 3/4 — — — — Inside *3 1/2 x 1/2 — — — — Inside *3 1/2 x 1/4 1.95 0.52 1.18 0.32 Inside 4x3 4.62 0.50 1.22 0.98 Outside 4 x 2 1/2 3.86 0.60 1.22 0.92 Inside 4x2 3.28 0.60 1.
PAGE 32
MALLEABLE IRON HEXAGON BUSHINGS CLASS 150 NPS Width of Head A Height of Head B Length of External Threads C (min) Length of Internal Threads D (min) Inside or Outside Head *1/4 x 1/8 0.64 0.14 0.44 0.26 Outside *3/8 x 1/4 0.68 0.160 0.48 0.40 Outside *3/8 x 1/8 0.68 0.16 0.48 0.25 Outside *1/2 x 3/8 0.87 0.19 0.56 0.36 Outside *1/2 x 1/4 0.87 0.19 0.56 0.32 Outside *1/2 x 1/8 0.87 0.19 0.56 0.25 Outside *3/4 x 1/2 1.15 0.22 0.63 0.53 Outside *3/4 x 3/8 1.
PAGE 33
CAST IRON FLUSH BUSHINGS CLASS 125 NPS Length of External Threads A (min) Length of Internal Threads B (min) 1 1/4 x 3/4 0.80 0.500 1 1/4 x 1/2 0.80 0.43 1 1/2 x 1 0.83 0.58 1 1/2 x 3/4 0.83 0.50 1 1/2 x 1/2 0.83 0.43 2 x 1 1/4 0.88 0.67 2x1 0.88 0.58 2 x 3/4 0.88 0.50 2 x 1/2 0.88 0.43 2 1/2 x 1 1/2 1.07 0.70 2 1/2 x 1 1/4 1.07 0.67 2 1/2 x 1 --- --- 2 1/2 x 3/4 --- --- 3x2 1.13 0.75 3 x 1 1/2 1.13 0.70 3 x 1 1/4 1.13 0.67 3x1 1.13 0.58 3 x 3/4 1.
PAGE 34
MALLEABLE IRON FLUSH BUSHINGS CLASS 150 NPS Overall Height A Length of External Threads B (min) +1/4 x 1/8 0.44 0.26 +3/8 x 1/4 0.48 0.40 +1/2 x 3/8 0.56 0.41 +1/2 x 1/4 0.56 0.32 +1/2 x 1/8 0.56 0.25 +3/4 x 1/2 0.63 0.53 +3/4 x 3/8 0.63 0.36 +3/4 x 1/4 0.63 0.32 1 x 3/4 0.75 0.50 1 x 1/2 0.75 0.43 1 x 3/8 0.75 0.43 1 x 1/4 0.75 0.36 1 1/4 x 1 0.80 0.58 1 1/2 x 1 1/4 0.83 0.77 2 x 1 1/2 0.88 0.70 2 1/2 x 2 1.07 0.75 3 x 2 1/2 1.13 0.92 3 1/2 x 3 1.
PAGE 35
CAST IRON DOUBLE TAP TANK BUSHINGS (Heavy Type Only) NPS Overall Height A Length of External Threads B (min) Width of Head C Inside or Outside Head *1 x 3/4 x 3/4 1.57 1.16 --- --- *1 x 1/2 x 1/2 1.57 1.16 1.46 Outside *1 1/2 x 1 x 1 1.58 1.16 2.02 Outside *2 x 1 1/2 x 1 1/2 1.74 1.33 2.59 Outside *2 x 1 1/4 x 1 1/4 1.77H 1.33 2.59 H Outside *2 x 1 x 1 1.57 1.16 2.55 Outside *2 x 3/4 x 3/4 1.57 1.16 2.55 Outside *2 x 1/2 x 1/2 1.57 1.16 2.
PAGE 36
SECTION 5 TOP BEAM CLAMPS AND “C” CLAMPS WARD Top Beam clamps and “C” clamps are manufactured from malleable iron with hardened steel cup point set screws and lock nuts. The finish is either black or galvanized. Top Beam clamps are recommended for use under roof installations with bar joist type construction, or for attachment to the top flange of steel shapes. “C” clamps are recommended for attachment to American Standard I-Beams and wide flange beams, where thickness of flange does not exceed .75 inches.
PAGE 37
MALLEABLE IRON SMALL MOUTH TOP BEAM CLAMP NPS Thread Size Recommended Pipe Size Type Dim A Dim B Dim C Dim D Dim E Dim F Dim G 3/8 3/8 - 16UNC 3/4- 4 SMALL 0.37 1.37 1.50 0.62 1.06 0.75 0.75 1/2 1/2 13UNC 5-8 SMALL 0.50 1.50 1.62 0.62 1.18 0.75 0.87       MALLEABLE IRON LARGE MOUTH TOP BEAM CLAMP NPS Thread Size Recommended Pipe Size Type Dim A Dim B Dim C Dim D Dim E Dim F Dim G 3/8 3/8- 16UNC 3/4 - 4 LARGE 0.37 1.56 1.50 0.62 1.06 0.75 0.
PAGE 38
SECTION 6 STANDARD CAST IRON PIPE FITTINGS CLASS 125, 250 The iron from which Class 125 cast iron fittings are made is held to strict formula by careful chemical analysis and control. Tapping is done on the most modern machines. All tappings are to USA Standards for iron pipe threads. Straightness and correct depth of threads is assured through continuous capable inspection, by careful trained inspectors. Every fitting is hand sorted and inspected to eliminate defective castings.
PAGE 39
CAST IRON 90 ˚ STRAIGHT ELL CLASS 125 NPS Center to End A Outside Dia.of Band B (min) Thread Length C (min) Take Out 1/4 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 3 3 1/2 4 5 6 8 0.81 0.95 1.12 1.31 1.50 1.75 1.94 2.25 2.70 3.08 3.42 3.79 — — — 0.93 1.12 1.34 1.63 1.95 2.39 2.68 3.28 3.86 4.62 5.20 5.79 — — — 0.32 0.36 0.43 0.50 0.58 0.67 0.70 0.75 0.92 0.98 1.03 1.08 — — — 0.408 0.5 0.58 0.76 0.81 1.04 1.21 1.49 1.56 1.88 2.17 2.
PAGE 40
CAST IRON 45 ˚ ELL CLASS 125 NPS Center to End A Outside Dia. of Band B (min) Length of Threads C (min) Take Out 1/4 — — — — 3/8 — — — — 1/2 0.88 1.34 0.43 0.34 3/4 0.98 1.63 0.50 0.43 1 1.12 1.95 0.58 0.43 1 1/4 1.29 2.39 0.67 0.58 1 1/2 1.43 2.68 0.70 0.70 2 1.68 3.28 0.75 0.92 2 1/2 1.95 3.86 0.92 0.81 3 2.17 4.62 0.98 0.97 3 1/2 — — — — 4 2.61 5.79 1.08 1.
PAGE 41
CAST IRON REDUCING TEES CLASS 125 D2 C E3 E2 B D3 A E D NPS Center to End A Center to End B Center to End C Outside Dia. of Band D (min) Outside Dia. of Band D2 (min) Outside Dia. of Band D3 (min) Length of Threads E (min) Length of Threads E2 (min)) Length of Threads E3 (min) Take Out Take Out Take Out 1/2 x 1/2 x 3/8 1.04 1.04 1.03 1.34 1.34 1.12 0.43 0.43 0.36 0.50 0.50 0.62 1/2 x 1/2 x 1/4 — — — — — — — — — — — — *1/2 x 3/8 x 1/2 1.12 1.12 1.12 1.34 1.
PAGE 42
CAST IRON REDUCING TEE CLASS 125 NPS Center to End A Center to End B Center to End C Outside Dia. of Band D (min) Outside Dia. of Band D2 (min) Outside Dia. of Band D3 (min) Length of Threads E (min) Length of Threads E2 (min)) Length of Threads E3 (min) Take Out Take Out Take Out 1 1/4 x 1 x 1/2 1.34 1.26 1.53 2.39 1.95 1.34 0.67 0.58 0.43 0.63 0.57 0.99 1 1/4 x 3/4 x 1 1/4 1.75 1.62 1.75 2.39 1.63 2.39 0.67 0.50 0.67 1.04 1.07 1.04 1 1/4 x 3/4 x 1 1.58 1.45 1.
PAGE 43
CAST IRON REDUCING TEE CLASS 125 NPS Center to End A Center to End B Center to End C Outside Dia. of Band D (min) Outside Dia. of Band D2 (Min) Outside Dia. of Band D3 (min) Length of Threads E (min) Length of Threads E2 (min) Length of Threads E3 (min) Take Out Take Out Take Out 1 x 1 x 1 1/2 1.80 1.80 1.65 1.95 1.95 2.68 0.58 0.58 0.70 1.11 1.11 0.92 2 x 2 x 1 1/2 2.02 2.02 2.16 3.28 3.28 2.68 0.75 0.75 0.70 1.26 1.26 1.43 2 x 2 x 1 1/4 1.90 1.90 2.10 3.28 3.
PAGE 44
CAST IRON REDUCING TEE CLASS 125 NPS Center to End A Center to End B Center to End C Outside Dia. of Band D (min) Outside Dia. of Band D2 (Min) Outside Dia. of Band D3 (min) Length of Threads E (min) Length of Threads E2 (min)) Length of Threads E3 (min) Take Out Take Out Take Out 2 1/2 x 2 1/2 x 1 1/4 2.04 2.04 2.45 3.86 3.86 2.39 0.92 0.92 0.67 0.90 0.90 1.74 2 1/2 x 2 1/2 x 1 1.87 1.87 2.37 3.86 3.86 1.95 0.92 0.92 0.58 0.73 0.73 1.68 2 1/2 x 2 1/2 x 3/4 1.87 1.
PAGE 45
CAST IRON REDUCING TEE CLASS 125 NPS Center to End A Center to End B Center to End C Outside Dia. of Band D (min) Outside Dia. of Band D2 (Min) Outside Dia. of Band D3 (min) Length of Threads E (min) Length of Threads E2 (min) Length of Threads E3 (min) Take Out Take Out Take Out 3 x 3 x 3/4 — — — — — — — — — — — — 3 x 3 x 1/2 — — — — — — — — — — — — 3 x 2 1/2 x 3 3.08 2.99 3.08 4.62 3.86 4.62 0.98 0.92 0.98 1.88 1.85 1.88 3 x 2 1/2 x 2 1/2 2.83 2.70 2.
PAGE 46
CAST IRON REDUCING TEE CLASS 125 NPS Center to End A Center to End B Center to End C Outside Dia. of Band D (min) Outside Dia. of Band D2 (Min) Outside Dia. of Band D3 (min) Length of Threads E (min) Length of Threads E2 (min) Length of Threads E3 (min) Take Out Take Out Take Out 4 x 4 x 2 1/2 3.05 3.05 3.51 5.79 5.79 3.86 1.08 1.08 0.92 1.75 1.75 2.37 4x4x2 2.74 2.74 3.41 5.79 5.79 3.28 1.08 1.08 0.75 1.44 1.44 2.65 4 x 4 x 1 1/2 2.51 2.51 3.32 5.79 5.79 2.
PAGE 47
CAST IRON CONCENTRIC REDUCING COUPLING CLASS 125 NPS Length of Coupling A Outside Dia. of Band Small End B (min) Outside Dia. of LargeEnd B2 (min) Length of Threads Small End C (min) Length of Threads Large End C2 (min) Take Out Take Out 3/4 x 1/2 1.50 1.31 1.62 0.43 0.50 0.20 0.22 1 x 1/2 1.70 1.31 1.99 0.43 0.58 0.85 0.85 1 x 3/4 1.70 1.63 1.99 0.50 0.58 0.85 0.85 1 1/4 x 1 2.130 1.95 2.39 0.58 0.67 0.17 0.30 1 1/4 x 3/4 2.13 1.95 2.39 0.50 0.67 0.17 0.
PAGE 48
CAST IRON ECCENTRIC REDUCING COUPLING CLASS 125 NPS Length of Coupling A Outside Dia. of Band Small End B1 (min) Outside Dia. of Large End B2 (min) Length of Threads Small End C1 (min) Length of Threads Large End C2 (min) Take Out Take Out 3/4 x 1/2 1.52 1.34 1.63 0.43 0.58 0.21 0.23 1 x 3/4 1.60 1.63 1.95 0.50 0.58 0.12 0.25 1 x 1/2 1.59 1.34 1.95 0.43 0.58 0.11 0.26 1 1/4 x 1 1.75 1.95 2.39 0.58 0.67 0.17 0.19 1 1/4 x 3/4 1.65 1.63 2.39 0.50 0.67 0.12 0.
PAGE 49
CAST IRON PIPE CAP CLASS 125 NPS Overall Height A Outside Dia. of Band B (min) Length of Threads C (min) 2 1/2 1.810 3.860 0.920 3 1.910 4.620 0.980 3 1/2 2.030 5.200 1.030 4 2.220 5.790 1.080 5 2.380 7.050 1.180 6 2.630 8.280 1.280 8 2.880 10.630 1.470 C B CAST IRON HEXAGON COUPLING 50 NPS Width Across Flats A HEX. Overall Length B Thread Length C Take Out Take Out 1 1.94 1.69 0.58 0.16 0.
PAGE 50
CAST IRON STRAIGHT CROSS CLASS 125 NPS Center to End A Outside Dia. Band B (min) Length of Threads C (min) Take Out 1/2 1.25 1.34 0.43 0.71 3/4 1.44 1.63 0.50 0.89 1 1.63 1.95 0.58 0.94 1 1/4 1.94 2.39 0.67 1.23 1 1/2 2.13 2.68 0.70 1.40 2 — — — — 4 — — — — A A C A B A CAST IRON REDUCING CROSS CLASS 125 NPS Center to End A Center to End A2 Outside Dia. Band B (min) Outside Dia.
PAGE 51
CAST IRON 90 ˚ STRAIGHT ELL CLASS 250 NPS 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 CAST IRON 45 ˚ STRAIGHT ELL CLASS 250 NPS 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 CAST IRON STRAIGHT TEE CLASS 250 NPS 3/8 1/2 3/4 1 1 1/4 1 1/2 2 2 1/2 CAST IRON REDUCING TEE CLASS 250 NPS 1 1/4 x 1 1/4 x 3/4 1 1/2 x 1 1/2 x 3/4 2 x 2 x 3/4 2 x 2 x 1 1/2 52
PAGE 52
SECTION 7 FLANGES, FLANGE UNIONS, COMPANION FLANGES, FLANGED FITTINGS WARD flange components are made with high quality iron and are designed to handle the tough service that flange components normally experience. Precision machining and thread chamfering allow WARD flange components to be easily installed. Most importantly, quality is built into the design, material and manufacturing of each of WARD’s flange components. Cast Iron flanges may have either a black or galvanized finish.
PAGE 53
CAST IRON FLANGE UNION CLASS 125 *WORKING PRESSURE 175 PSI NPS Outside Flange Dia. A Overall Height B (min) Dia. of Hub C (min) Thickness of Flange D (min) Number of Bolt Holes Bolt Hole Size Bolt Circle Dia. Dia. of Bolts Length of Bolts *1/2 2.81 0.62 1.31 0.43 3 0.44 1.69 0.44 1.75 *3/4 3.43 0.75 1.75 0.43 3 0.50 2.31 0.44 1.75 *1 3.50 0.75 1.88 0.43 3 0.50 2.50 0.44 1.75 *1 1/4 4.06 0.75 2.25 0.43 4 0.50 3.00 0.44 1.75 *1 1/2 4.37 0.81 2.5 0.
PAGE 54
MALLEABLE IRON FLOOR FLANGE NPS Outside Overall Flange Height Dia. B (min) A Length of Threads C (min) Number of Bolt Holes Bolt Hole Size Bolt Circle Dia. D *1/4 2.37 0.46 0.32 3 0.27 1.86 *3/8 2.93 0.52 0.36 4 0.27 1.93 *1/2 3.00 0.65 0.43 4 0.24 2.10 *3/4 3.25 0.65 0.50 4 0.25 2.31 *1 3.87 0.77 0.58 4 0.27 3.00 *1 1/4 3.87 0.77 0.67 4 0.27 3.00 *1 1/2 4.50 0.99 0.70 4 0.30 3.60 *2 5.50 1.00 0.75 4 0.39 4.25 *2 1/2 5.81 1.06 0.92 4 0.
PAGE 55
H CAST IRON EXTRA HEAVY FLANGE UNION CLASS 250 NPS Outside Overall Flange Height Dia. B (min) A Dia. of Hub C (min) Thickness of Flange D (min) Number of Bolt Holes Bolt Hole Size Bolt Circle Dia. Dia. of Bolts Length of Bolts *2 5.50 1.06 3.25 0.81 5 0.56 4.50 0.50 2.50 *2 1/2 6.00 1.06 3.81 0.81 5 0.66 4.75 0.63 2.75 *3 6.81 1.18 4.38 0.81 6 0.69 5.35 0.63 2.75 *4 8.18 1.25 5.44 0.75 7 0.69 6.38 0.63 3.
PAGE 56
CAST IRON STRAIGHT COMPANION FLANGE NPS Outside Overall Flange Length Dia. B (min) A Dia. of Hub C (min) Thickness of Flange D (min) Number of Bolt Holes Bolt Hole Size Bolt Circle Dia. 3/4 — — — — — — — 1 4.250 0.690 1.940 0.440 4 0.620 3.120 1 1/4 4.620 0.810 2.310 0.500 4 0.620 3.500 1 1/2 5.000 0.880 2.560 0.560 4 0.620 3.880 2 6.000 1.000 3.060 0.620 4 0.750 4.750 2 1/2 7.000 1.120 3.560 0.690 4 0.750 5.500 3 7.500 1.190 4.250 0.750 4 0.
PAGE 57
CAST IRON REDUCING COMPANION FLANGE NPS 3/4 x 1 1/2 1 x 1 1/2 1x2 1x3 1 1/4 x 2 1 1/4 x 3 1 1/2 x 2 1 1/2 x 2 1/2 1 1/2 x 3 1 1/2 x 4 1 1/2 x 6 2 x 2 1/2 2x3 2x4 2x5 2x6 2x8 2 1/2 x 3 2 1/2 x 4 2 1/2 x 5 2 1/2 x 6 3 x 3 1/2 3x4 3x5 3x6 3x8 3 1/2 x 4 4x5 5x6 5x8 6x8 58 Outside Overall Flange Height Dia. B (min) A 5.00 0.69 5.00 0.69 6.00 0.69 7.50 0.69 6.00 0.81 7.50 6.00 7.00 7.50 9.00 11.00 7.00 7.50 9.00 10.00 11.00 13.50 7.50 9.00 10.00 11.00 8.50 9.00 10.00 11.00 13.50 9.00 10.00 11.00 13.50 13.50 0.
PAGE 58
CAST IRON FLANGED STRAIGHT 90˚ELL CLASS 125 NPS Center to Face A Outside Flange Dia. B Thickness of Flange C (min) 2 2 1/2 3 4 5 6 8 10 12 4.500 5.000 5.500 6.500 7.500 8.000 9.000 11.000 12.000 6.000 7.000 7.500 9.000 10.000 11.000 13.500 16.000 19.000 0.620 0.690 0.750 0.940 0.940 1.000 1.120 1.190 1.250 Wall Number Thickness of Bolt D Holes 0.310 0.310 0.380 0.500 0.500 0.560 0.620 0.750 0.810 4 4 4 8 8 8 8 12 12 Bolt Hole Size Bolt Circle Dia. Dia. of Bolts Length of Bolts 0.75 0.75 0.
PAGE 59
CAST IRON FLANGED REDUCING 90˚ ELL CLASS 125 Outside Outside Flange Flange Dia. Dia. B B2 Thickness of Flange C (min) Thickness of Flange C2 (min) Wall Thickness D Wall Thickness D2 7.000 0.750 0.690 0.380 0.310 7.500 6.000 0.750 0.620 0.380 0.310 6.500 9.000 7.500 0.940 0.750 0.500 0.380 4 x 2 1/2 6.500 9.000 7.000 0.940 0.690 0.500 0.310 4x2 6.500 9.000 6.000 0.940 0.620 0.500 0.310 5x4 8.000 10.000 9.000 0.940 0.940 0.500 0.500 6x5 8.000 11.000 10.000 1.
PAGE 60
CAST IRON FLANGED 90˚ STRAIGHT ELL LONG RADIUS CLASS 125 NPS Center to Face A Outside Flange Dia. B Thickness of Flange C (min) Wall Thickness D Number of Bolt Holes Bolt Hole Size Bolt Circle Dia. Dia. of Bolts Length of Bolts 2 6.500 6.000 0.620 0.310 4 0.75 4.75 5/8 2 1/4 2 1/2 7.000 7.000 0.690 0.310 4 0.75 5.50 5/8 2 1/2 3 7.750 7.500 0.750 0.380 4 0.75 6.00 5/8 2 1/2 4 9.000 9.000 0.940 0.500 8 0.75 7.50 5/8 3 6 11.500 11.000 1.000 0.560 8 0.
PAGE 61
CAST IRON FLANGED 45˚ STRAIGHT ELL CLASS 125 NPS Center to Face A Outside Flange Dia. B Thickness of Flange C (min) Wall Thickness D Number of Bolt Holes Bolt Hole Size 2 2.500 6.000 0.620 0.310 4 0.75 4.75 5/8 2 1/4 2 1/2 3.000 7.000 0.690 0.310 4 0.75 5.50 5/8 2 1/2 3 3.000 7.500 0.750 0.380 4 0.75 6.00 5/8 2 1/2 4 4.000 9.000 0.940 0.500 8 0.75 7.50 5/8 3 5 4.500 10.000 0.940 0.500 8 0.88 8.50 3/4 3 6 5.000 11.000 1.000 0.560 8 0.88 9.
PAGE 62
CAST IRON FLANGED 22 1/2˚ STRAIGHT ELL CLASS 125 NPS Center to Face A Outside Flange Dia. B Thickness of Flange C (min) Wall Thickness D Number of Bolt Holes Bolt Hole Size Bolt Circle Dia. Dia. of Bolts Length of Bolts 2 2.500 6.000 0.620 0.310 4 0.75 4 .75 5/8 2 1/4 2 1/2 3.000 7.000 0.690 0.310 4 0.75 5.50 5/8 2 1/2 3 3.000 7.500 0.750 0.380 4 0.75 6.00 5/8 2 1/2 4 4.000 9.000 0.940 0.500 8 0.75 7.50 5/8 3 6 5.000 11.000 1.000 0.560 8 0.88 9.
PAGE 63
CAST IRON FLANGED REDUCING TEE CLASS 125 Outside Outside Outside Flange Flange Flange Dia. Dia. Dia. B B2 B3 Thickness of Flange C (min) Thickness of Flange C2 (min) Thickness of Flange C3 (min) 9.000 0.750 0.750 0.940 7.500 7.000 0.750 0.750 0.690 7.500 6.000 0.750 0.750 0.620 9.000 7.500 9.000 0.940 0.750 0.940 9.000 7.500 7.500 0.940 0.750 0.750 6.500 9.000 6.000 9.000 0.940 0.620 0.940 8.000 9.000 9.000 11.000 0.940 0.940 1.000 NPS Center to Face A 3x3x4 5.
PAGE 64
CAST IRON FLANGED CONCENTRIC REDUCING COUPLING CLASS 125 NPS 2 1/2 x 2 3 x 2 1/2 3x2 4x3 4 x 2 1/2 4x2 5x4 5x3 6x5 6x4 6x3 6 x 2 1/2 6x2 8x6 8x5 8x4 8x3 10 x 8 10 x 6 10 x 4 12 x 10 12 x 8 12 x 6 12 x 4 Center Outside Outside to Face Flange Flange A Dia. B Dia. B2 5.500 6.000 6.000 7.000 7.000 7.000 8.000 8.000 9.000 9.000 9.000 9.000 9.000 11.000 11.000 11.000 11.000 12.000 12.000 12.000 12.000 12.000 12.000 12.000 7.000 7.500 7.500 9.000 9.000 9.000 10.000 10.000 11.000 11.000 11.000 11.000 11.000 13.
PAGE 65
CAST IRON FLANGED 45˚ LATERAL CLASS 125 NPS Center to Face A Outside Flange Dia. B Thickness of Flange C (min) Wall Thickness D Number of Bolt Holes Bolt Hole Size Bolt Circle Dia. Dia. of Bolts Length of Bolts 2 1/2 9.500 7.000 0.690 0.310 4 0.75 5.50 5/8 2 1/2 3 10.000 7.500 0.750 0.380 4 0.75 6.00 5/8 2 1/2 4 12.000 9.000 0.940 0.500 8 0.75 7.50 5/8 3 6 14.500 11.000 1.000 0.560 8 0.88 9.50 3/4 3 1/4 8 17.500 13.500 1.120 0.620 8 0.88 11.
PAGE 66
CAST IRON FLANGED REDUCING CROSS CLASS 125 Outside Outside Flange Flange Dia. Dia. B B2 Thickness of Flange C (min) Thickness of Flange C2 (min) Wall Thickness D Wall Thickness D2 6.000 1.000 0.620 0.560 0.310 11.000 9.000 1.000 0.940 0.560 0.500 13.500 11.000 1.120 1.000 0.620 0.560 12.000 19.000 16.000 1.250 1.190 0.810 0.750 12.000 19.000 13.500 1.250 1.120 0.810 0.620 12.000 19.000 7.500 1.250 0.750 0.810 0.380 NPS Center to Face A 6x2x2 8.000 11.
PAGE 67
CAST IRON FLANGED STRAIGHT STANDARD BASE TEES CLASS 125 NPS Center to Face A Outside Flange Dia. B Thickness of Flange C (min) Wall Thickness D Height of Base E Round and Square Base F Number of Bolt Holes Bolt Hole Size 3 5.500 7.500 0.750 0.380 4.875 5.000 4 4 6.500 9.000 0.940 0.500 5.500 6.000 8 5 7.500 10.000 0.940 0.500 7.000 7.000 8 6 8.000 11.000 1.000 0.560 7.000 7.000 8 8 9.000 13.500 1.120 0.620 8.375 9.000 10 11.000 16.000 1.190 0.750 9.
PAGE 68
SECTION 8 CAST IRON DRAINAGE FITTINGS WARD cast iron drainage fittings, shown on the following pages, are designed especially for drainage systems using wrought pipe. The inside diameter of the fitting is the same as that of wrought pipe. WARD drainage fittings are made with an interior shoulder, so that when the joint is made the end of the pipe practically meets the shoulder. This forms a continuous unobstructed surface providing smooth flow of the pipe contents.
PAGE 69
CAST IRON DRAINAGE 45˚ ELL SHORT TURN NPS Center to End A Outside Dia. of Band B (min) Length of Threads C (min) Take Out 1 1/4 1.31 2.39 0.42 0.60 1 1/2 1.44 2.68 0.42 0.71 2 1.69 3.28 0.44 0.93 3 2.19 4.62 0.77 0.99 4 2.63 5.79 0.84 1.33 A B A C CAST IRON DRAINAGE 45˚ ELL LONG TURN Center to End A Outside Dia. of Band B (min) Length of Threads C (min) Take Out 1 1/2 — — — — 2 2.25 3.28 0.44 1.
PAGE 70
CAST IRON DRAINAGE 90˚ STRAIGHT ELL LONG TURN NPS Center to End A Outside Dia. of Band B (min) Length of Threads C (min) Take Out 1 1/2 2.50 2.68 0.42 1.77 2 3.06 3.28 0.44 2.30 3 4.25 4.62 0.77 3.00 A B B B A C CAST IRON DRAINAGE 90˚ STRAIGHT ELL EXTRA LONG TURN NPS Center to End A Outside Dia. of Band B (min) Length of Threads C (min) Take Out 1 1/2 3.50 2.68 0.42 2.77 2 4.00 3.28 0.44 3.
PAGE 71
CAST IRON DRAINAGE 45˚ STREET ELL Outside Port Dia. Dia. of Male Band End C (min) D (max) NPS Center to End A Center to Male B 1 1/2 1.50 1.87 2.68 2 1.65 2.30 3.28 Length of Internal Threads E (min) Length of External Threads F (min) Take Out Male End Take Out Female End 1.35 0.42 0.85 1.15 0.77 1.75 0.44 0.87 1.54 0.89 A C E B F D CAST IRON DRAINAGE 60˚ STREET ELL SHORT TURN NPS Center to End A Outside Dia. of Band B (min) Length of Threads C (min) Take Out 1 1/2 1.75 2.
PAGE 72
CAST IRON DRAINAGE 90˚ “TY” SHORT TURN Center to End Inlet A NPS Center to End Outlet B Center to End C 8 Outside Outside Outside Dia. of Dia of Dia. of Band. Band. Band E7 (min) E2 (min) 6E3 (min) End to End D 1 1/2 2.50 2.50 1.75 4.25 2 3.06 3.06 2.13 4 5.19 5.19 2 x 1 1/2 2.94 2 x 1 1/2 x 1 1/2 2 x 1 1/2 x 2 A A Length of Threads F (min)5 Length of Threads F2 (min) Length of Threads F3 (min) 4 Take Out 0.42 0.42 0.42 1.78 1.78 Take Out 2 3 2.68 2.68 2.68 5.19 3.
PAGE 73
CAST IRON DRAINAGE 90˚ “TY” LONG TURN Outside Outside Outside Dia. of Dia. of Dia. of Band Band Band E (min)) E2 (min) E3 (min) NPS Center to End Inlet A Center to End Outlet B Center to End C End to End D 1 1/2 4.13 4.13 1.25 5.38 2.68 2.68 2 5.25 5.25 1.75 7.00 3.28 3.28 2 x 1 1/2 4.38 4.44 1.31 5.75 3.28 2 x 1 1/2 x 1 1/2 4.38 4.44 1.31 5.75 2 x 1 1/2 x 2 5.25 5.25 1.75 7.00 Length of Threads F (min) Length of Threads F1 (min) Length of Threads F2 (min) 2.68 0.
PAGE 74
CAST IRON DRAINAGE 90˚ DOUBLE “TY” SHORT TURN Outside Outside Dia. of Dia. of Band Band E (min) E2 (min) NPS Center to End Inlet A Center to End Outlet B Center to End C End to End D 1 1/2 2.50 2.50 1.75 4.25 2.68 2 3.06 3.06 2.13 5.19 3.28 2 x 1 1/2 2.90 2.69 1.94 4.63 3.28 Length of Threads F (min) Length of Threads F2 (min) 2.68 0.42 0.42 3.28 0.44 0.44 2.68 0.44 0.
PAGE 75
SECTION 9 WARDLOX ™ Introduced in 1983, the WARDLOX sprinkler connect system is a fast, safe and effective way to join schedule 10 and 40 plain end pipe without threading or welding. In addition to the performance benefits of threadless sprinkler connect systems, the WARDLOX system is 100% factory tested to prevent leaks and recalls. WARDLOX has also been thoroughly field tested in a variety of installations and is ideal for new construction and retrofit.
PAGE 76
8 5 6 7 4 3 WARDLOX 90˚ ELBOW (SLIP X SLIP) D NPS Center to End A Pipe Engagement Take Out Schedule Pipe Approved 1 2.37 1.62 0.75 40, 10, XL, DT, D 1 1/4 2.56 1.62 0.94 40, 10, XL, DT, D 1 1/2 2.68 1.62 0.69 40, 10 2 3.06 1.75 0.94 40, 10 C A TAKE OUT C TAKE OUT A C WARDLOX ADAPTER ELBOW (SLIP X THREAD) NPS Center to End B A1 Center to End A2 Pipe Engagement Take Out Schedule Pipe Approved 1x1 1.56 2.56 1.62 0.93 40, 10, XL, DT, DF 1 x 3/4 1.56 2.44 1.
PAGE 77
WARDLOX REDUCING SLIP TEES (SLIP X SLIP X SLIP) NPS Pipe Pipe Center Engagement Engagement to Outlet A A2 B 2x2x1 1.79 1.64 Overall Length C Take Out Take Out 2 Schedule Pipe Approved 5.38 1.30 1.45 40, 10 3.09 2 x 2 x 1 1/4 1.79 1.63 3.13 5.38 1.34 1.50 40, 10 2 x 2 1 1/2 1.79 1.63 3.13 5.97 1.34 1.50 40, 10 B A2 TAKEOUT A C WARDLOX BULLHEAD TEES (SLIP X SLIP X SLIP) NPS 1 1/2 x 1 1/2 x 2 Center to End A 3.00 Pipe Center to Engagement Outlet C1 C2 1.62 1.
PAGE 78
WARDLOX REDUCING OUTLET TEES (SLIP X SLIP X THREAD) NPS Center to End A Pipe Pipe Engagement Engagement C1 C2 1 1/4 x 1 x 1 1.84 1.62 1 1/4 x 1 x 3/4 1.84 1 1/4 x 1 x 1/2 Take Out Schedule Pipe Approved 1.62 0.50 40, 10, XL, DT, D 1.62 1.62 0.50 40, 10, XL, DT, D 1.84 1.62 1.62 0.50 40, 10, XL, DT, D 1 1/2 x 1 1/4 x 1 1.96 1.62 1.62 0.50 40, 10 1 1/2 x 1 1/4 x 3/4 1.96 1.62 1.62 0.50 40, 10 1 1/2 x 1 1/4 x1/2 1.96 1.62 1.62 0.50 40, 10 2 x 1 1/2 x 1 2.16 1.75 1.
PAGE 79
SECTION 10 TEELOX ™ MECHANICAL BRANCH CONNECTOR Designed for fast installation of bolted branch outlets, Teelox™ mechanical branch connectors are practical alternatives to existing branch connect systems. Made from high quality cast iron, Teelox™ are known for long-lasting, maintenance-free performance. J Features: J Key • A high grade EPDM rubber gasket surrounds the locating collar for accurate, permanent installation and the best seal in the industry.
PAGE 80
NPS Length of Coupling A Outside Dia. B (min) 1/2 1 9/16 1.063 1/2 3/4 1 5/8 1.313 3/4 1 2 1.576 1 1 1/4 2 1/16 1.900 1 1/4 1 1/2 2 1/16 2.200 1 1/2 2 2 1/8 2.750 2 2 1/2 3 1/8 3.250 2 1/2 3 3 1/4 4.000 3 4 3 1/2 5.000 4 5 3 3/4 6.296 5 6 4 7.390 6 FULL STEEL B NPS STEEL STRAIGHT COUPLING A TOLERANCES AND SPECIFICATIONS UNLESS OTHERWISE NOTED: SURFACE FINISH: DECIMAL PLACE: .X ±.03 .XX ±.01 .XXX ±.005 63 MACHINED SURFACES ANGULARITY: ±1 ±.031 FOR THE FIRST INCH, AND AN ADDITIONAL ±.
PAGE 81
Made in America, right here in Blossburg, Pennsylvania WARD MANUFACTURING, LLC • 117 Gulick Street • Blossburg, PA 16912 PH: 800-248-1027 www.wardmfg.com ® ® Also made right here in America ® ® ® ® ® www.wardflex.com www.wardmfg.com www.wisnip.
PAGE 82