Brochure

SECTION 10 TEELOX
™
MECHANICAL BRANCH CONNECTOR
Designed for fast installation of bolted branch outlets,
Teelox™ mechanical branch connectors are
practical alternatives to existing branch connect
systems. Made from high quality cast iron, Teelox™ are
known for long-lasting, maintenance-free performance.
Key Features:
• A high grade EPDM rubber gasket surrounds the
locating collar for accurate, permanent installation
and the best seal in the industry.
• The locating collar is an integral part of the casting.
• A zinc-plated high-tensile steel U-bolt ensures rust-free
attachment.
• Teelox™ is approved for conventional and arm-over
installations.
Material: Cast Iron ASTM A126 Class A Minimum
Gasket: E.P.D.M. Rubber ASTM D-2000
U Bolt: Zinc Plated High-Tensile Steel
Dimensions: ANSI/ASME B1.20.1
Pressure Ratings: 175 psi
Coatings: ASTM B633, ASTM A153
Additional UL, ULC and FM where applicable
Specifications:
Torque 20 ft.-lbs. max.
Requirement:
NPS
Pipe Center
to Outlet
A
Hole Dia.
B
Take
Out
1 1/4 x 1/2 1.98 1.19 1.19
1 1/4 x 3/4 2.05 1.19 1.19
1 1/4 x 1 2.13 1.19 1.19
1 1/2 x 1/2 1.98 1.19 1.19
1 1/2 x 3/4 2.05 1.19 1.19
1 1/2 x 1 2.13 1.19 1.19
2 x 1/2 2.26 1.19 1.47
2 x 3/4 2.33 1.19 1.47
2 x 1 2.41 1.19 1.47
2 1/2 x 1/2 2.57 1.19 1.78
2 1/2 x 3/4 2.64 1.19 1.78
2 1/2 x 1 2.72 1.19 1.78
J J
C
A
OUT
TAKE
Section 11 Page 81
Teelox Mechanical Branch Connector
X.BTLX
All information contained within this document is intended for the sole use of Ward Manufacturing
and may not be released, used, copied, or distributed without the express written permission of ...
WARD MANUFACTURING LLC
BLOSSBURG, PA. 16912, USA
[phone]
TITLE:
MATERIAL:
DRAWN BY:
SHEET:
DATE:
CHECKED BY:
DATE:
SCALE:
SIZE:
SMARTEAM I.D.:
DATE
DESCRIPTION
APR
PART NO.:
REV.
XX-XXXXXXXXX
E.C.O. #
NEW SOLIDWORKS DRAWING
01
XXX
ANGULARITY: ±1
SURFACE FINISH:
63
±.031 FOR THE FIRST INCH,
AND AN ADDITIONAL ±.005
FOR EACH ADDITIONAL INCH
DECIMAL PLACE:
.X ±.03
.XX ±.01
.XXX ±.005
AS-CAST SURFACES
MACHINED SURFACES
UN THREADS - EXTERNAL: CLASS 2A, INTERNAL: CLASS 2B
TOLERANCES AND SPECIFICATIONS
UNLESS OTHERWISE NOTED:
THIS IS A CAD DRAWING,
DO NOT ADD HAND WRITTEN EDITS
XX/XX/XX
1
OF
1
B
ALL DIMENSIONS ARE IN INCHES UNLESS OTHERWISE NOTED
DRAWN IN ACCORDANCE WITH ASME Y14.5
BREAK ALL SHARP CORNERS AND REMOVE ALL BURRS
DRAFT ANGLE IS 2° UNLESS NOTED OTHERWISE
THREADS:
REV.
80