Brochure

MALLEABLE IRON REDUCING TEES CLASS 300
NPS
Center
to End
A
Center
to End
B
Center
to End
C
Outside
Dia. of
Band
D (min)
Outside
Dia. of
Band
D2 (min)
Outside
Dia. of
Band
D3 (min)
Length of
Threads
E (min)
Length of
Threads
E2 (min)
Length of
Threads
E3 (min)
Take
Out
Take
Out
Take
Out
3/4 x 3/4 x 1/2 1.31 1.31 1.38 1.63 1.63 1.34 0.64 0.64 0.57 0.76 0.76 0.84
3/4 x 3/4 x 3/8 — — — — — — — — — — — —
3/4 x 3/4 x 1/4 — — — — — — — — — — — —
3/4 x 1/2 x 3/4 — — — — — — — — — — — —
3/4 x 1/2 x 1/2 — — — — — — — — — — — —
1 x 1 x 3/4 1.50 1.50 1.56 1.95 1.95 1.63 0.75 0.75 0.64 0.81 0.81 1.01
1 x 1 x 1/2 1.44 1.44 1.50 1.95 1.95 1.34 0.75 0.75 0.57 0.75 0.75 0.96
1 x 1 x 1/4 — — — — — — — — — — — —
1 x 3/4 x 1 — — — — — — — — — — — —
1 x 3/4 x 3/4 — — — — — — — — — — — —
1 x 1/2 x 1 — — — — — — — — — — — —
1 1/4 x 1 1/4 x 1 1.75 1.75 1.81 2.39 2.39 1.95 0.84 0.84 0.75 1.04 1.04 1.12
1 1/4 x 1 1/4 x 3/4 1.63 1.63 1.75 2.39 2.39 1.63 0.84 0.84 0.64 0.92 0.92 1.20
1 1/4 x 1 1/4 x 1/2 — — — — — — — — — — — —
1 1/4 x 1 x 1 — — — — — — — — — — — —
1 1/2 x 1 1/2 x 1 1/4 — — — — — — — — — — — —
1 1/2 x 1 1/2 x 1 1.81 1.81 2.00 2.68 2.68 1.95 0.87 0.87 0.75 1.08 1.08 1.31
1 1/2 x 1 1/2 x 3/4 1.69 1.69 1.88 2.68 2.68 1.63 0.87 0.87 0.64 0.96 0.96 1.33
1 1/2 x 1 1/2 x 1/2 1.63 1.63 1.81 2.68 2.68 1.34 0.87 0.87 0.57 0.90 0.90 1.27
2 x 2 x 1 1/2 2.25 2.25 2.38 3.28 3.28 2.68 1.00 1.00 0.87 1.49 1.49 1.65
2 x 2 x 1 1/4 — — — — — — — — — — — —
2 x 2 x 1 2.00 2.00 2.25 3.28 3.28 1.95 1.00 1.00 0.75 1.24 1.24 1.56
2 x 2 x 3/4 1.81 1.81 2.13 3.28 3.28 1.63 1.00 1.00 0.64 1.05 1.05 1.58
2 x 2 x1/2 1.75 1.75 2.06 3.28 3.28 1.34 1.00 1.00 0.57 0.99 0.99 1.52
2 x 1 1/2 x 2 — — — — — — — — — — — —
2 1/2 x 2 1/2 x 2 — — — — — — — — — — — —
2 1/2 x 2 1/2 x 1 1/2 — — — — — — — — — — — —
3 x 3 x 2 2.81
2.81 3.13 4.62 4.62 3.28 1.23 1.23 1.00 1.61 1.61 2.37
H H
D3
D2
C
E3
E2
E
A B
D
SECTION H-H
Section 2 Page 17
Malleable Iron Reducing Tee, Class 300
X.B300T
All information contained within this document is intended for the sole use of Ward Manufacturing
and may not be released, used, copied, or distributed without the express written permission of ...
WARD MANUFACTURING LLC
BLOSSBURG, PA. 16912, USA
[phone]
TITLE:
MATERIAL:
DRAWN BY:
SHEET:
DATE:
CHECKED BY:
DATE:
SCALE:
SIZE:
SMARTEAM I.D.:
DATE
DESCRIPTION
APR
PART NO.:
REV.
XX-XXXXXXXXX
E.C.O. #
NEW SOLIDWORKS DRAWING
01
XXX
ANGULARITY: ±1
SURFACE FINISH:
63
±.031 FOR THE FIRST INCH,
AND AN ADDITIONAL ±.005
FOR EACH ADDITIONAL INCH
DECIMAL PLACE:
.X ±.03
.XX ±.01
.XXX ±.005
AS-CAST SURFACES
MACHINED SURFACES
UN THREADS - EXTERNAL: CLASS 2A, INTERNAL: CLASS 2B
TOLERANCES AND SPECIFICATIONS
UNLESS OTHERWISE NOTED:
THIS IS A CAD DRAWING,
DO NOT ADD HAND WRITTEN EDITS
XX/XX/XX
REDUCING TEE, CLASS 300 (FOR CHARTED)
X.B300T
Malleable Iron ASTM A197
1
OF
1
B
ALL DIMENSIONS ARE IN INCHES UNLESS OTHERWISE NOTED
DRAWN IN ACCORDANCE WITH ASME Y14.5
BREAK ALL SHARP CORNERS AND REMOVE ALL BURRS
DRAFT ANGLE IS 2° UNLESS NOTED OTHERWISE
THREADS:
REV.
20