Operation Manual

19
GB
Possible error messages:
t -POHTJHOBMTTFDTJHOBMTTFDOPTPVOEEVS-
ing ignition  indicate that the batteries of the re-
ceiver are almost exhausted. (The appliance can still
be switched on for another 10 times after hearing this
signal.)
t TFDPOETDPOUJOVPVTTJHOBMÂ is an error message. It
may indicate that one of the cables is not connected
PSUIBUUIFiO IwTXJUDIJTOPUJOUIFiI” position.
t CSJFGTJHOBMTTFDTJHOBMTTFDOPTPVOEÂ
JOEJDBUFUIBUJHOJUJPOPGUIFQJMPUnBNFBOEUIFNBJO
burner has failed. Possible reason is air in the pilot-
nBNFDPOOFDUJPO
Important: If the pilot flame has extinguished you must
wait at least 5 MINUTES before repeating the above ac-
tions.
Setting the height of the flames
t "GUFSJHOJUJPOPGUIFCVSOFSUIFnBNFIFJHIUXJMMBV-
tomatically be in the highest position.
t $POUJOVPVTMZ QSFTT CVUUPO d UP MPXFS UIF nBNFT
and to extinguish the burner (extinguishing the fire:
iSTAND BYw#SJFnZQSFTTJOHCVUUPOd will gradu-
BMMZMPXFSUIFnBNFT
t 1SFTTJOH CVUUPO c XJMM HJWF IJHIFS nBNFT #SJFnZ
pressing button dXJMMHSBEVBMMZSBJTFUIFnBNFT
Switching off the appliance
t 1SFTTCVUUPOdUPEFDSFBTFnBNFIFJHIUBOEUPTXJUDI
off the appliance.
t 5IFOQSFTTiOFF” button e to switch off the whole
BQQMJBODFJODMVEJOHUIFQJMPUnBNF
t *GUIFBQQMJBODFXJMMOPUCFVTFEGPSBMPOHFSUJNFJUJT
advisable to close the gas tap in the gas supply pipe.
Important: If for whatever reason the pilot flame has ex-
tinguished you must wait 5 MINUTES before lighting the
pilot again.
Malfunctioning
If it appears that the signals of the remote control are not
(properly) picked up by the stove (receiver), this may be
caused by:
t %FBECBUUFSJFTSFQMBDFCBUUFSJFT
t "OFMFDUSJDBMQSPCMFNUPCFSFNFEJFECZQSFTTJOHUIF
iRESET” button on the receiver.
t 4IPVMEUIFBQQMJBODFTIVUJUTFMGPGGSFHVMBSMZZPVOFFE
to contact your installer.
Operation (manual)
If the batteries are dead or if the receiver is defect, the
stove can also be manually operated. First disengage the
ignition cable (piezo) cable from the receiver and care-
fully slide it onto the piezo connection of the gas control
block.
Ignition of the fire
1. Open the gas shut-off cock, which is fitted on the
gas pipe to the appliance.
 1SFTTiO I” switch g on the gas control block in the
iI” position.
3. Turn motor switch i on the gas control block com-
pletely to the right; the switch will make a ticking
sound.
4. Turn control switch h on the gas control block to
the MAN position; an opening in the control switch
will become visible j.
5. Press the metal pin in the opening, with a pointed
JOTUSVNFOUFHBQFO5IFHBTXJMMnPXUPUIFQJ-
lot.
 5PJHOJUFUIFQJMPUnBNFQSFTTUIFTRVBSFJHOJUJPO
switch k OFYUUPUIFiO I” switch) several times
while keeping the pressure on the metal pin. Check
UISPVHIUIFHMBTTXJOEPXJGUIFQJMPUnBNFJTCVSO-
ing.
7. Once the pilot is burning, keep the metal pin
pressed for another 10 seconds, and then release
g
h
h
g
i
j
k