BL19101 ASSEMBLY INSTRUCTIONS NANTUCKET VINYL PICKET FENCE WITH POST AND NO-DIG STEEL PIPE ANCHOR KIT ASSEMBLY INSTRUCTIONS BL19101 (4’H X 6’W) 60 MIN Approximate assembly time Want to see a video on how to assemble this product? Scan the QR code WWW.WAMBAMFENCE.COM WWW.WAMBAMFENCE.COM 1VER.
BL19101 ASSEMBLY INSTRUCTIONS GENERAL INFORMATION IMPORTANT k Check the inside of the larger pieces in your box for other materials packed inside. k When assembling components, place on a non-abrasive surface (i.e. shipping box) to avoid scratching. k We recommend an area approximately 5’x 8’ for unobstructed assembling. k You should not need to use excessive force when assembling components.
BL19101 ASSEMBLY INSTRUCTIONS TIPS 1. Run a string line to help establish the post location(s). 2. To space the pipe anchors more easily, use a piece of wood measuring 70⅜” in length from the inside gear to the next pipe anchor. 3. After you have installed the first two vinyl posts and have checked your spacing, temporarily remove the posts to create an unobstructed string line. 4. When cutting PVC, use a saw with a fine-toothed blade. Donut Wood Spacer Inside Gear 5.
BL19101 ASSEMBLY INSTRUCTIONS AVOID THESE PITFALLS! HAVE YOU CONTACTED YOUR LOCAL UTILITIES? 1 You must call your local utilities before you start installing your fence to avoid puncturing any unseen underground utilities, especially electrical or gas lines. Fortunately, this is made easy for you. k Simply call 811 in the US or visit www.call811.com. k In Canada, visit www.transcanada.com/contactus.html for a list of phone numbers by province.
BL19101 ASSEMBLY INSTRUCTIONS DETAILED PRODUCT DIMENSIONS AND SPECIFICATIONS 1 in 3.46 in 1.5 in 1.5 in. Pipe Anchor Detail 3.5 in. 3.5 in 4in x 4in Post 48 in 33 in 26 in 26in. 3.5 in 3 to 4 in 2 in Ground 68 in 72 in 1.5 in 32.5 in Ground 3.5 in .090 in. Wall Thickness 1 5/8in Galvanized Pipe WWW.WAMBAMFENCE.
BL19101 ASSEMBLY INSTRUCTIONS STEP 1: LAY OUT MATERIALS A B Post Cap (1) C G Post (1) 4” x 4” x 53” D Bracket (4) H Top Rail (1) 1½” x 3½” x 67¾” E Picket (13) ⅞” x 1½” x 44¼” F Donut and gear Bottom Rail (1) 1½” x 3½” x 67¾” 6 Pipe Anchor (1) 1⅝” Diameter x 58½” L 1” Self-Drilling Stainless Steel Screw (24) WWW.WAMBAMFENCE.
BL19101 ASSEMBLY INSTRUCTIONS STEP 2: INSTALL PIPE ANCHORS AND POSTS STEP 2.1 After establishing your fence lines with string and stakes, drive your first Pipe Anchor (F) into the ground. The bottom of the donut should sit just above the ground when finished. Note: Try to drive the pipe anchor as level as possible. Check level about every 12”.
BL19101 ASSEMBLY INSTRUCTIONS STEP 2.5 STEP 2.4 Adjust the bottom and top donuts to compensate for a crooked pipe anchor. Slide the Posts (B) down over the donuts. B Note: The ground can be dug out about 3” to 4” to allow post bottoms to sit below the ground if necessary. STEP 3: INSTALL BRACKETS AND BOTTOM RAILS STEP 3.2 STEP 3.1 Place the second bracket over the opposite end of the Bottom Rail (E) and slide the rail down into the bracket on the opposing side.
BL19101 ASSEMBLY INSTRUCTIONS STEP 3.3 Use a level on the top of the bottom rail to determine the height of the opposing bracket, and mark for installation. STEP 3.5 Insert the bottom rail into the lower brackets and secure the rail with (4) total 1” self-drilling stainless steel screws. STEP 3.4 Temporarily remove the bottom rail and install the lower brackets using (4) total 1” self-drilling stainless steel screws. STEP 3.
BL19101 ASSEMBLY INSTRUCTIONS STEP 4: INSTALL PICKETS AND POST CAPS STEP 4.1 D Install the Pickets (D) by inserting them through the top rail and locking them into the bottom rail. Note: Pickets cannot be removed once inserted. STEP 4.2 Trim down the tops of the posts if necessary, and install the Post Caps (A). Use PVC glue (not included) to secure permanently. A INSTALL ONE COMPLETE PANEL OF FENCE FIRST.
BL19101 ASSEMBLY INSTRUCTIONS 6935 Reames Rd. Ste. K. Charlotte, NC 28216 hmmm@wambamfence.com 704-892-5222 877-778-5733 WWW.WAMBAMFENCE.COM WWW.WAMBAMFENCE.
