Item #: BWTOTMS Revised 06/2017 P.
7.5 in. H on the upper 7.5 in.
Parts List 8 20 3 15 12 8 12 11 5 7 18 6 14 14 9 4 10 15 16 1 3 7 2 18 6 17 18 18 2 9 6 1 19 19 P.
Hardware List Ref. A B C D E G H K L Qty. 1/4x100mm 7x100mm 7x50mm 10x100mm 10x40mm 4,0x50mm 4,0x30mm Hex Key NUT 08 30 14 04 46 12 66 01 08 P.
Assembly Options Option A Twin over Twin Bunk Bed Option B Conversion into Two Single Twin Beds P.
Step 1 E E E 11 E 10 9 x2 E 12 x2 E E 14 E x2 E E 18 x4 E E E E E E E E 6 E x3 E E E 20 E E x46 10x40 P.
Step 2 8 B G B k G B G 6 3 3 B 4 4 x4 B x1 K x3 G Step 3 8 B G B k G B G 3 20 3 B 5 5 x4 B x3 G x1 K P.
Step 4 7 B G B k G 2x B G 6 1 1 B 2 2 x8 B x1 K x6 G Step 5 C 17 C C 18 16 C 18 k C 18 C 18 17 C C 16 x8 C x1 K P.
Step 6 B B A k B A B 4 L 11 12 L 12 3 x2 A x4 B x1 K 9 x2 L Step 7 B B A B A 12 12 B L 11 3 k L 5 9 x2 A x4 B x1 K x2 L P.
Step 8 A k B A B 2 L 10 L 1 9 x2 A x2 B x1 K x2 L Step 9 A B A B L 10 1 k L 2 9 2 1 x2 A x2 B x1 K x2 L P.
Step 10 H H H H H H H H H H H 2" H H H 19 H H H H H H H H H H H H H 19 H H H H 19 The first slat must be fixed at 2” from each headboard end. H H H H H H H H H H H H H 19 H H H H H H H H H H H H H ``INSTALL SLAT KIT WITH SPACER TAPE ON TOP (FACING UP)`` x52 H P.
Step 11 D D D D x4 D Step 12 H H H H H H x08 H H H H H P.
Step 13 C C C C K C C C C K x4 C x1 K P.
Step 14 C C C C 14 B 14 B k B B x2 B k x2 C x1 K Step 15 37 927m" m H H H 2 7359m" m H H H x6 H P.
Step 16 Option B Conversion into Two Single Twin Beds P.
Step 17 Loosen the appropriate hardware and remove the ladder from the bunk bed assembly. P.
Step 18 P.
Step 19 Carefully lift the upper bunk off of the lower bunk. P.
Step 20 15 12 12 4 11 14 3 14 19 15 9 3 5 Loosen the appropriate hardware of the upper bunk so that the guardrails and leg assemblies are no longer connected to the bed assembly. P.
Step 21 A B 4 A B LL 11 3 L 9 A L 3 B A 5 B k Step 22 Option B Final Assembly P.
