User Manual

ManualsBrandsWalker Edison ManualsBeds & Bed FramesWalker Edison - Chevron 64" Queen-Size Standard Bed - Caramel

P.1

Item #: BWQCHEV

Keep these instructions for future reference.

Revised 03/2018

Summary of content (10 pages)

PAGE 1
Item #: BWQCHEV Keep these instructions for future reference. Revised 03/2018 P.
PAGE 2
P.
PAGE 3
5 1 3 4 2 9 11 10 6 11 8 9 7 12 P.
PAGE 4
Hardware List A 1/4"x90 mm Bolt 08 pcs B 7.0x100 mm Bolt 10 pcs C 7.0x70 mm Bolt 02 pcs D 4.0x30 mm Screw 18 pcs E 3.0x16 mm Screw 06 pcs F 10x40 mm Wood dowel 10 pcs G 1/4" Barrel nut 08 pcs Bracket 01 pcs Hex key 01 pcs H I M4 Tape measure recommended for assembly (not included) Mallet or hammer recommended for assembly (not included) P.
PAGE 5
Step 1 F Insert wood dowel ( F ) into rails ( 8, 9 ) and slat legs ( 11 ). F 9 F F 9 8 F (2x) F 11 F F F Step 2 Attach leg ( 1 ) to slat ( 2 ) using bolt ( B ). 1 B I B 1 B B 2 + 2 2 P.
PAGE 6
Step 3 Slide headboard ( 3 ) into slat ( 2 ) gently. Ensure headboard ( 3 ) is pressed ﬁrmly against leg ( 1 ). 3 2 1 Step 4 Attach leg ( 4 ) to slat ( 2 ) using bolt ( B ). Secure headboard ( 3 ) to slat ( 2 ) using screw ( D ). 4 D B B D 3 D D D 1 D 2 B B I P.
PAGE 7
Step 5 B X Attach headboard cap ( 5 ) to headboard ( 3 ) using bolt ( B ). Ensure headboard cap ( 5 ) sits ﬂush on top of headboard ( 3 ). 5 X 3 B I B Step 6 Attach legs ( 6, 7 ) to slat ( 8 ) using bolt ( B ). Attach bracket ( H ) to pre-drilled holes on the slat ( 8 ) using screw ( E ). B B 7 I B 8 EE B H EE EE H B 6 B P.
PAGE 8
Step 7 Insert barrel nut ( G ) into pre-drilled holes on rails ( 9 ). Attach rails ( 9 ) to headboard ( 3 ) using bolt ( A ). Bolt ( A ) will screw into barrel nut ( G ). 1º ! G + G G A I 2º A G G A A G 9 G G I A 9 G 3º Step 8 Insert barrel nut ( G) into pre-drilled holes on rails ( 9 ). Attach rails ( 9 ) to legs ( 6, 7 ) using bolt ( A ). Bolt ( A ) will screw into barrel nut ( G). 1º G 2º G G A A I A G A A 3º G P.
PAGE 9
Step 9 Attach slat legs ( 11 ) to slat support beam ( 10 ) using bolt ( C ). I C C 10 C 11 10 11 11 Step 10 Attach slat support beam ( 10 ) to bracket ( H ) using screw ( E ). E E 10 10 P.
PAGE 10
Step 11 Attach slat support (12) to rails (9) and slat support beam (10) using screw (D). Ensure slat are spaced 3 inches from headboard (3). 3 3" D D D 12 D 10 3 D D D 9 D D D 12 D D 9 D Step 12 Final Assembly. P.