BR6DDDR Assembly Instructions Keep these instructions for future reference. Revised 03/2018 P.
P.
1 2 16 7 12 14 6 13 3 15 11 2x 9 7 5 8 9 12 14 4 13 8 10 11 4x 9 1 Top panel 01 pcs 9 Left foot 03 pcs 2 Right side panel 01 pcs 10 Front drawer 04 pcs 3 Left side panel 01 pcs 11 Left side drawer 06 pcs 4 Bottom front crossbeam 01 pcs 12 Right side drawer 06 pcs 5 Back crossbeam 01 pcs 13 Drawer bottom 06 pcs 6 Upper front crossbeam 01 pcs 14 Drawer back 06 pcs 7 Back panel 02 pcs 15 Upper front drawer 02 pcs 8 Right foot 02 pcs 16 Division 0
A Ø8*30mm Wooden dowel 45 pcs B Ø3,0*14mm Screw 30 pcs C Ø6,0*10mm Screw 12 pcs D Ø4,0*30mm Screw 70 pcs E M4*22mm Screw 12 pcs F Ø4,5*45mm Screw 14 pcs G Ø10*10 Nail 36 pcs H 350mm Right Slide 06 pcs I 350mm Left Slide 06 pcs J Knob 12 pcs K Glue 01 pcs L 1374mm “H” Profile 01 pc M Ø6,0*20mm Screw 12 pcs N Ø15*10mm Spacer Slide 18 pcs O Wall anchor 01 pc P Washer 02 pc Q Ø6mm 01 pc Screw 06 pcs R Ø3,0*20mm Tape measure and
Step 1 A A A A A A 2 3 A A Please assemble on a clean soft surface to avoid damage.
Step 3 3 D 16 4 D D D D 5 K 01 Glue tube D 04 Ø4,0*30mm Step 4 6 2 D D K 01 Glue tube D 02 Ø4,0*30mm P.
Step 5 D D 1 D D D D K 01 Glue tube D 09 Ø4,0*30mm Step 6 D D D D DD D D D 05 Ø4,0*30mm P.
Step 7 9 F F 8 F F F F 9 F F F F 8 F F Apply glue to leg contact surfaces 9 F 1º 2º K F F F 14 Ø4,5*45mm K 01 Glue tube Step 8 7 G G G G G 69 G G G L 7 G G 7 L G G 8mm G G G G G G G G G G G G 7 G G G G G G G G G G G G G 36 Ø10*10 L 01 P.
Step 9 14 12 D D D D 11 13 D D D The wheel to the Back D 15 2x 2x B E B B I Bottom E J B B J H 2x 2x E B B 04 I 02 Left slide 350mm 08 H Ø3,0*14mm D M4x22mm 16 02 J 04 Right slide 350mm Ø4,0*30mm Step 10 14 12 D D D D 11 13 D D D D 10 The wheel to the Back 4x 4x B E B B I Bottom E J B B J H 4x B B E 16 Ø3,0*14mm D 32 Ø4,0*30mm M4x22mm 08 4x I 04 Left slide 350mm H 04 J 08 Right slide 350mm P.
Step 11 To adjust the drawer front position: Loosen the screw (part C or M) you used to install the drawer runner (either parts H or I) in step 2, to the side panel (parts 02 or 03), depending on the side (left or right), or division ( part 16) as shown. With the screw (part C or M) loosened, you can make the necessary slight adjustments (up or down) to the drawer runner to achieve the proper drawer alignment.
Wall anchor and hardware are included with this product. Please make sure hardware is suitable for your walls before installing, as different wall materials may require different types of anchors. 1º 2º O Q Top P P D D Wall Back panel Top Ø6mm = = D 02 Ø4,0*30mm O 01 P 02 Q 01 P.
