User Manual

ManualsBrandsWalker Edison ManualsDressersWalker Edison - Modern 4-Drawer Dresser - White

BR4DDR

Assembly Instructions

P.1

Keep these instructions for future reference.

Revised 05/2018

Summary of content (10 pages)

PAGE 1
BR4DDR Assembly Instructions Keep these instructions for future reference. Revised 05/2018 P.
PAGE 2
P.
PAGE 3
1 7 7 6 2 12 14 13 5 10 11 3 4x 5 4 9 02 pcs 8 8 9 1 Top panel 01 pcs 8 Right foot 02 pcs 2 Right side panel 01 pcs 9 Left foot 02 pcs 3 Left side panel 01 pcs 10 Front drawer 04 pcs 4 Bottom front crossbeam 01 pcs 11 Left side drawer 04 pcs 5 Back crossbeam 02 pcs 12 Right side drawer 04 pcs 6 Upper front crossbeam 01 pcs 13 Drawer bottom 04 pcs 7 Back panel 02 pcs 14 Drawer back 04 pcs P.
PAGE 4
A Ø8*30mm Wooden dowel 36 pcs B Ø3,0*14mm Screw 24 pcs C Ø6,0*10mm Screw 16 pcs D Ø4,0*30mm Screw 50 pcs E M4*22mm Screw 08 pcs F Ø4,5*45mm Screw 12 pcs G Ø10*10 Nail 24 pcs H 300mm Right Slide 04 pcs I 300mm Left Slide 04 pcs J Knob 08 pcs K Glue 01 pcs “H” Profile 01 pc M Wall anchor 01 pc N Washer 02 pc O Ø6mm 01 pc L 808 mm Hammer recommended for assembly (not included) P.
PAGE 5
Step 1 Please assemble on a clean soft surface to avoid damage. A A A A 2 A A 3 A AA 6 12 4x AA A 4 A 11 4x 2x AA K A A AA 5 A A 01 Glue tube A 36 Ø8*30mm Step 2 Please assemble on a clean soft surface to avoid damage. C C C C C I C H C H C I H I 2 C H C I The wheel to the Front C C C C 3 C C C C I C Pre-Drilled holes 16 Ø6,0*10mm H 04 Right slide 300mm I H The wheel to the Front 04 Left slide 300mm P.
PAGE 6
Step 3 3 6 D 5 4 D 2 D D D 5 K D 01 Glue tube D 06 Ø4,0*30mm Step 4 1 D D D D K 01 Glue tube D 06 Ø4,0*30mm P.
PAGE 7
Step 5 D D D D D D 04 Ø4,0*30mm Step 6 9 F F 8 F F F F 8 F F F F 9 Apply glue to leg contact surfaces 1º F 2º K F F F 12 Ø4,5*45mm K 01 Glue tube P.
PAGE 8
Step 7 L G G G G G G G 7 G L 7 G 7 G 7 G G G G G G G G G G G G G 24 Ø10*10 G G L 01 Step 8 14 12 D D D D 11 13 D D D 10 The wheel to the Back D 4x 4x B B B E I E Bottom J B B J H 4x 4x E 08 M4x22mm B B 16 Ø3,0*14mm D 32 Ø4,0*30mm I 04 Left slide 350mm H 04 J 08 Right slide 350mm P.
PAGE 9
Step 9 To adjust the drawer front position: Loosen the screw (part C) you used to install the drawer runner (either parts H or I) in step 2, to the side panel (parts 02 or 03), depending on the side (left or right), as shown. With the screw (part C) loosened, you can make the necessary slight adjustments (up or down) to the drawer runner to achieve the proper drawer alignment.
PAGE 10
Wall anchor and hardware are included with this product. Please make sure hardware is suitable for your walls before installing, as different wall materials may require different types of anchors. 1º 2º M O Top N N D D Wall Top Back panel Ø6mm = = D 02 Ø4,0*30mm M 01 N 02 O 01 P.