CONTROL PRO 130 POWER TANK ™ OWNER‘S MANUAL • GUIDE D‘UTILISATION • MANUAL DEL PROPIETARIO READ THIS MANUAL FOR COMPLETE INSTRUCTIONS • LIRE CE MANUEL POUR OBTENIR DES DIRECTIVES COMPLÈTES • LEA ESTE MANUAL PARA OBTENER LAS INSTRUCCIONES COMPLETAS www.wagnerspraytech.com EN F ENGLISH FRANÇAIS ESPAÑOL ES P. 2 P. 20 P. 38 1121 • Form No.
IMPORTANT SAFETY INFORMATION TABLE OF CONTENTS EXPLANATION OF SYMBOLS IMPORTANT SAFETY INFORMATION____________________ 2-4 Explanation of Symbols_________________________________ 2 Grounding Instructions_________________________________ 3 Important Electrical Information__________________________ 3 Safety Hazards______________________________________ 3-4 Read all safety information before operating the equipment. Save these instructions.
IMPORTANT SAFETY INFORMATION GROUNDING INSTRUCTIONS IMPORTANT ELECTRICAL INFORMATION This product must be grounded. In the event of an electrical short circuit, grounding reduces the risk of electric shock by providing an escape wire for the electric current. This product is equipped with a cord having a grounding wire with an appropriate grounding plug. The plug must be plugged into an outlet that is properly installed and grounded in accordance with all local codes and ordinances.
IMPORTANT SAFETY INFORMATION • • • • • • • High-pressure spray is able to inject toxins into the body and cause serious bodily injury. In the event that injection occurs, seek medical attention immediately. WARNING: EXPLOSION OR FIRE Solvent and paint fumes can explode or ignite. Severe injury and/or property damage can occur. Check hoses and parts for signs of damage, a leak can inject material into the skin. Inspect hose before each use. Replace any damaged hoses or parts.
IMPORTANT SAFETY INFORMATION GENERAL INFORMATION SPECIFICATIONS WARNING: HAZARDOUS VAPORS Paints, solvents, insecticides, and other materials can be harmful if inhaled or come in contact with the body. Vapors can cause severe nausea, fainting, or poisoning. Control Pro 130 Power Tank Maximum Pressure 1600 PSI (11.1 MPa) Capacity 0.24 GPM (0.91 LPM) Tank Capacity 1.5 gallon (5.7 l) PREVENTION: Horsepower 0.38 • Max. tip 0.
PARTS AND COMPONENTS A Tank lid Spray hose B Inlet filter (A) Tank k Spray tip Spray gun PRIME Material return tube ON/OFF switch p SPRAY PRIME/SPRAY knob (B) Spray hose port ASSEMBLY The PRIME/SPRAY knob can be turned in either direction to desired setting (vertical = PRIME, horizontal = SPRAY). 1 Do not plug in the power cord until assembly is complete. i Remove the plastic cap from the spray hose port and the plastic plug from the end of the spray hose prior to assembly.
BEFORE YOU BEGIN i This section contains instructions that will be repeated throughout this manual. Read and understand this section before using the equipment. SPRAY GUN TRIGGER LOCK Engage the trigger lock whenever instructed. LOCKED The gun is locked when the trigger lock is at a 90º angle (perpendicular to the trigger in either direction). PRESSURE RELIEF PROCEDURE 1 2 Be sure to follow the Pressure Relief Procedure when shutting the unit off for any purpose.
LOAD MATERIAL i These steps will prime the system and get it ready to spray. www.wagnercontrolpro.com/howtoCP130 YOU WILL NEED • • • 1 PUSH The material you plan to spray Extension cord Waste bucket i Recommendation: It is good practice to perform the steps on this page using water to familiarize yourself with the function of the unit as well as to ensure the unit is set up properly. i Recommendation: Always use new spray material or material that has been thoroughly strained.
SPRAYING i Follow these steps to deliver spray material from the tank to the spray gun. 1 YOU WILL NEED • • • Waste bucket 1. Make sure the tip and spray guard are removed. Point the spray gun into a separate waste container. Unlock the spray gun trigger. 2 Scrap material / cardboard Drop cloths to protect floors and furnishings from overspray 0 p Squeeze and hold trigger for steps 2-3. 2. Turn the power ON (l). 3 Turn the PRIME/SPRAY knob to SPRAY. 3.
PRACTICE SPRAYING YOU WILL NEED • A surface to practice spraying (wood, carboard or scrap drywall) While spraying, the spray guard / tip assembly can be rotated to better suit your spraying motion. Lock the spray gun trigger prior to rotating the spray guard / tip assembly. Make sure the spray guard nut is not loosened after rotating. Trigger gun after starting the stroke. Release the trigger before ending the stroke. The spray gun should be moving when the trigger is pulled and released.
SPRAYING TROUBLESHOOTING - CLEAR THE SPRAY TIP i If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the spray tip could be clogged. Follow the steps below. YOU WILL NEED • 1 Scrap material / cardboard Do not attempt to unclog or clean the tip with your finger. High pressure fluid can cause injection injury. 2 1. Lock the spray gun. 2. Rotate spray tip 180 degrees from its current position.
SPRAYING TROUBLESHOOTING - CLEAN THE INLET FILTER i If the spray pattern becomes distorted or stops spraying completely while the gun is triggered, the inlet filter could be clogged. Follow the steps below. YOU WILL NEED • • 1 Warm, soapy water for latex material Mineral spirits for oil based materials Make sure your floors and furnishings are covered with drop cloths to prevent accidental drips. Attention PAGE 7 2 1. Perform the Pressure Relief Procedure, page 7. 2.
SHORT TERM STORAGE i This procedure should be used when taking a short term break or when ending your project for the day. If your break is longer than 16 hours follow Cleanup instructions, pages 14-15. YOU WILL NEED • • • • k 1 Water Plastic bag Damp rags Stir stick i Instructions are for latex materials only! If using oil based material follow instructions for Cleanup on pages 14-15. PAGE 7 2 SHUTDOWN AND 1. Perform the Pressure Relief Procedure, page 7. 2. Turn spray tip 90º.
CLEANUP CLEANING NOTES - READ BEFORE CLEANING FOLLOW THESE STEPS WHENEVER CLEANING WITH MINERAL SPIRITS: • When using latex material, clean sprayer and components with warm, soapy water. For oil based material use mineral spirits. Never use mineral spirits with latex materials. • If spraying or cleaning with oil-based materials, the spray gun must be grounded while preparing the spray hose or cleaning. • • • NEVER use gasoline to clean sprayer.
CLEANUP - CONTINUED 6 6. Perform Pressure Relief Procedure (page 7). 7. Remove the inlet filter. Clean by hand using a soft-bristled brush. Snap back into place when clean. k Remove the tip guard and spray tip from the cleaning solution. Clean by hand using a soft bristled brush. 8. IMPORTANT STEP: Fill the tank with warm, soapy water. Following steps 5-7 in the “Spraying” section, spray at least one gallon of warm, soapy water.
LONG TERM STORAGE i Follow these steps to prepare your sprayer for longterm storage. YOU WILL NEED 1 • Light household oil (such as 10W30 motor oil or vegetable oil for example) / All Guard • • Rags 1. Pull trigger guard from gun housing. 2. Tighten the wrench over the wrench flats (a). Unscrew the gun housing using a wrench. 3. Tip the spray gun upside down and pour a few drops of All Guard inside the gun housing nut (DO NOT remove the nut).
MAINTENANCE - CLEANING THE INLET VALVE i Cleaning or servicing the inlet valve may be required if the unit has priming problems. Priming problems may be prevented by properly cleaning the sprayer and following the long-term storage steps. YOU WILL NEED • • • • • 1 1 8 mm (5/16”) hex wrench Needle nose pliers 2 Warm, soapy water if using latex material Mineral spirits for oil based material Household oil (such as 10W30 motor oil or vegetable oil for example) TAPER 1.
MAINTENANCE - CLEANING THE OUTLET VALVE i Cleaning or servicing the outlet valve may be necessary if spray performance remains poor after following the steps in the Troubleshooting section. Call Technical Service (1-800-3288251) to order a new outlet valve assembly. YOU WILL NEED 1 • • • • Two 6” adjustable wrenches 1. Place a wrench on the outlet valve to secure it. Using the second wrench, remove the spray hose. 2.
TROUBLESHOOTING PROBLEM CAUSE SOLUTION A. The sprayer does not turn on. 1. The sprayer is not plugged in. 2. The sprayer is turned OFF (0). 3. The sprayer shuts off while under pressure. 1. Plug the sprayer in. 2. Switch the sprayer ON (l). 3. Motor will cycle ON and OFF while spraying to regulate pressure. This is normal. 4. Reset circuit breaker or find another outlet. 5. Refer to General Information. 4. No power is coming from power outlet. 5.
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS MAIN ASSEMBLY • ENSEMBLE PRINCIPAL • MONTAJE PRINCIPAL 1 4 5 2 3 # 130 Description Description Descripción 1 0580538A Tank lid Couvercle de la réservoir Tapa de la tanque 2 0580072A Outlet valve assembly Ensemble de la soupape de sortie Conjunto de la válvula de salida 3 0580070 Set screw Vis de pression Tornillo de ajuste 4 0580662A Inlet filter Filtre d'entrée Filtro de entrada 5 0580732 Inlet valve kit Trousse de la soupape d'
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS SPRAY GUN ASSEMBLY • PISTOLET DE PULVÉRISATION • PISTOLA DE ROCIADORA 1 2 3 Replacement parts available by calling customer service On peut obtenir des pièces de rechange en appelant le Service à la clientèle. 4 Los repuestos están disponibles llamanado al servicio a clientes.
ACCESSORIES • ACCESSOIRES • ACCESORIOS PART NO.
WARRANTY AIRLESS PAINT SPRAY EQUIPMENT This product, manufactured by Wagner, is warranted to the original retail purchaser against defects in material and workmanship for two years from date of purchase. This warranty does not cover damage resulting from improper use, accidents, user’s negligence or normal wear. This warranty does not cover any defects or damages caused by service or repair performed by anyone other than a Wagner Authorized Service Center. This warranty does not apply to accessories.
QUESTIONS? BESOIN D’AIDE? Call Wagner Technical Service at: Appelez le service technique Wagner Register your product online at: Enregistrement du produit en ligne sur le site : 1-800-328-8251 1-800-328-8251 www.wagnerspraytech.com www.wagnerspraytech.com ¿NECESITA AYUDA? Llame Wagner Technical Service al: 1-800-328-8251 Regístrelo del producto en línea en: www.wagnerspraytech.
