multisprayer ™ Owner’s Manual Read this manual for complete instructions Français - page 15 / Español - página 29 Contents 2 3 4 5 6 7 8 0211 Important Safety Information Before You Begin Features Setup Practice Spraying Spraying Technique Spraying Troubleshooting • Form No.
Important Safety Safety Information Read all safety information before operating the equipment. Save these instructions Indicates a hazardous situation which, if not avoided, could result in death or serious injury. a) To reduce the risks of fire or explosion, electrical shock and the injury to persons, read and understand all instructions included in this manual. Be familiar with the controls and proper usage of the equipment. Grounding Instructions This product must be grounded.
Safetyyou begin: Before This page contains information that is necessary in order to operate the sprayer properly. Material Preparation: • It is important to mix the material thoroughly before you begin. Do not shake the material to mix it. Always stir the material gently but thoroughly before use. • Remove any skin that has formed on the top of the material. Do not mix the skin into the material. The skin can break up and clog the sprayer. Older paint may need to be strained.
Features e a b f b h g1 Sprayer b Spray tip c Suction tube d 1 quart container e Flow control knob f Trigger g Pump assembly g c Features a i g g1 - Locking nut g2 - Atomizer valve (2) g5 g1 g2 g4 d g3 - Pump housing g4 - Spring g3 g5 - Piston h Cleaning brush i Spray tip removal tool English 4
Setup 1 2 3 (a) Start You will need: (b) MULTI-PURPOSE OIL • Household oil Note: The cup will give you approximately 3-5 minutes of continuous spraying time. iMPORTANT: Avoid running the cup dry. An empty cup will allow air to become sucked into the sprayer, which leads to globbing and spitting. 1. Remove the cup. 2. Fill the container with the material to be used. 3. Place a few drops of household oil down the intake (a) and return openings (b) in the pump housing. 5 4 4.
Safety Practice Spraying Start You will need: • a scrap piece of wood or cardboard Important - read before spraying Flow Control Knob The spray pattern is controlled by the Flow Control Knob on the rear of the sprayer, and by the thickness of the material being sprayed. Turning the flow knob counterclockwise increases the amount of material flow. Turning the flow knob clockwise decreases the amount of material flow. Practice Spraying 1 2 1. Turn the flow knob fully counterclockwise to maximum. 2.
Spraying Technique 1 Keep stroke even Start Aproximately 10 to 14 inches Before you begin: Never tip the sprayer at more than a 45º angle when spraying overhead. Material could get into the motor housing and cause an electric shock. Start stroke Pull trigger Move steadily Release trigger End stroke 1. Keep your arm moving at constant speed and keep the sprayer at a constant distance from the surface.
Spraying Troubleshooting Start Material spitting a b c b. A suction tube that is not fully inserted into the intake opening. c. Tipping the sprayer too far in one direction. recommendation: Firmly install the suction tube into the intake opening. recommendation: Keep your arm even and steady when spraying. Adjust the spray tip to change spraying direction. Notice: Material “spitting” will occur any time you introduce air to the system, such as during refilling.
Cleanup Start 1 2 3 4 You will need: • Waste container • Warm soapy water if you sprayed latex materials • Mineral spirits if you sprayed oil-based materials Make sure you clean the sprayer in a well-ventilated area whenever cleaning with flammable solvents. The sprayer contains electrical parts. Do not submerge the sprayer into any liquids. 5 5. Slide the pump housing off the sprayer. 1. Unplug the sprayer. Pour the remaining material back into the original container.
Reassembly / Maintenance Start You will need: • Scrap piece of wood or cardboard • Household oil 1 2 MULTI-PURPOSE OIL 1. Slide the spring onto the front end of the piston. Insert the piston into the back of the pump housing. 4 4. Insert the atomizer valve into the front end of the pump housing. Place the spray tip onto the pump housing and turn it clockwise until it is tightened securely. English 3 5 (a) 2. Insert the pump housing assembly into the front of the sprayer. 6 (b) 5.
Replacement parts Start Notice: Parts of your sprayer wear out with use and require regular replacement. They include the atomizer valve, piston and spring. These parts are not covered by your sprayer warranty. More abrasive materials such as latex paints and stains cause these parts to wear out faster than less abrasive materials such as oil-based paints and stains, thin stains and sealers. Atomizer valve: The atomizer valve is shaped to cause the material to spin as it comes out of the sprayer.
Any attempt to open the motor housing or repair any electrical parts within the unit by anyone other than an authorized repair technician could cause serious injury and will void the warranty. Troubleshooting Problem A: Motor will not run 1. Cause No power at wall outlet. Electrical problem or defective motor. Solution Try new wall outlet. Take to Authorized Service Center for repair. Problem B: Motor has a low hum and does not spray 1. 2.
Troubleshooting Problem E: Excessive fogging 1. 2. Cause Pressure too high Holding sprayer too far from work surface Solution Turn flow control knob clockwise to reduce pressure and flow Hold sprayer closer to work surface Problem F: Runs and sags in paint 1. Cause Arm movement too slow, holding spray gun too close or work surface, or applying too much paint at one time Solution See section on spraying (page 7) Problem G: Material drips from spray tip or guard 1.
Parts List • Liste de pièces • Lista de piezas (a) (f) (b) (c) (g) (d) (h) (j) (k) (e) (i) English Français Español 42
Parts List • Liste de pièces • Lista de piezas Item Article Articulo Part No. Nº de piéce Pieza No.
WAGNER ONE-YEAR LIMITED WARRANTY - Keep on File GARANTIE LIMITÉE D’UN AN - À conserver GARANTíA LIMITADA POR UN AÑO - Manténgala archivada This product, manufactured by Wagner Spray Tech Corporation (Wagner) is warranted against defects in material and workmanship for one year following date of purchase if operated in accordance with Wagner’s printed recommendations and instructions. This warranty does not cover damage resulting from improper use, accidents, user’s negligence or normal wear.
