Translation of the Original Operating Manual Cobra 40-10 Version 10/2013 High-pressure Double Diaphragm Pumps B_04234
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Table of Contents 1 1.1 1.2 1.3 1.4 ABOUT THIS OPERATING MANUAL Preface Warnings, Notices, and Symbols in this Operating Manual Languages Abbreviations in the Text 5 5 5 6 6 2 2.1 2.2 2.3 2.4 2.5 2.5.1 2.6 2.7 CORRECT USE Device Types Type of Use Use in an Explosion Hazard Area Safety Parameters Processible Working Materials Recommended Application Areas Reasonably Foreseeable Misuse Residual Risks 7 7 7 7 7 8 8 9 9 3 3.1 3.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Table of Contents 6 6.1 6.1.1 6.1.2 6.2 6.2.1 6.2.2 6.2.3 ASSEMBLY AND COMMISSIONING Installation and Connection Installing the Pump Grounding Commissioning Safety Instructions Basic Flushing Filling with Working Material 25 25 25 26 28 28 31 32 7 7.1 7.2 7.3 7.4 OPERATION Spraying Work Interruption Decommissioning and Cleaning Long-term Storage 33 33 33 34 34 8 8.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 1 ABOUT THIS OPERATING MANUAL 1.1 PREFACE The operating manual contains information about safely operating, maintaining, cleaning and repairing the device. The operating manual is part of the device and must be available to operating and service staff. Operating and service staff should be instructed according to the safety instructions. The device may only be operated in compliance with this operating manual.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 1.3 LANGUAGES The operating manual is available in the following languages: Language Order No. Language Order No. German 2303152 English 2303675 French 2303676 Dutch 2303677 Italian 2303678 Spanish 2303679 Danish 2303680 Swedish 2303682 Portuguese 2343519 1.4 ABBREVIATIONS IN THE TEXT Order No.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 2 CORRECT USE 2.1 DEVICE TYPES Double diaphragm pump and spray pack: 2.2 TYPE OF USE The device is suitable for processing liquid materials like paints and lacquers in accordance with the classification into explosion classes IIA or IIB. 2.3 USE IN AN EXPLOSION HAZARD AREA The double diaphragm pump can be employed in explosion hazard areas (Zone 1). 2.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 2.5 PROCESSIBLE WORKING MATERIALS Fluid products such as paints and lacquers.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 2.6 REASONABLY FORESEEABLE MISUSE The following is prohibited: coating work pieces which are not grounded, unauthorized conversions and modifications to the double diaphragm pump, processing dry or similar coating products, and using defective components, spare parts, or accessories other than those described in Chapter 10 of this operating manual.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 3 IDENTIFICATION 3.1 EXPLOSION PROTECTION IDENTIFICATION As defined in Directive 94/9/EC (ATEX 95), the device is suitable for use in potentially explosive areas. European Communities Symbol for explosion protection Device class II Category 2 (Zone 1) Ex-atmosphere gas Explosion group Constructional safety Special Notes (see Chapter 3.2) 3.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 4 GENERAL SAFETY INSTRUCTIONS 4.1 SAFETY INSTRUCTIONS FOR THE OPERATOR Keep this operating manual to hand near the device at all times. Always follow local regulations concerning occupational safety and accident prevention. 4.1.1 ELECTRICAL EQUIPMENT Electrical devices and equipment To be provided in accordance with the local safety requirements with regard to the operating mode and ambient influences.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 4.2 SAFETY INSTRUCTIONS FOR STAFF Always follow the information in these instructions, particularly the general safety instructions and the warning instructions. Always follow local regulations concerning occupational safety and accident prevention. 4.2.1 SAFE HANDLING OF WAGNER SPRAY DEVICES The spray jet is under pressure and can cause dangerous injuries. Avoid injection of paint or cleaning agents: Never point the spray gun at people.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 4.2.2 GROUNDING THE DEVICE In order to avoid electrostatic charging of the device, the device must be grounded. Friction, flowing liquids, and air or electrostatic coating processes create charges. Flames or sparks can form during discharge. Ensure that the device is grounded for every spraying operation. Ground the work pieces to be coated. Ensure that all persons inside the working area are grounded, e.g.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 4.2.4 CLEANING De-energize the device electrically. Disconnect the pneumatic supply line. Relieve the pressure from the device. Ensure that the flash point of the cleaning agent is at least 5 K above the ambient temperature. To clean, use cloths and brushes moistened with solvent. Never use hard objects or spray on cleaning agents with a gun. Preferably, non-combustible cleaning agents should be used.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 4.3 USE IN AREAS SUBJECT TO EXPLOSION HAZARDS The pneumatic pump may be used in potentially explosive areas. The following safety regulations must be observed and followed. 4.3.1 SAFETY REGULATIONS Safe handling of WAGNER spray devices Mechanical sparks can form if the device comes into contact with metal. In an explosive atmosphere: Do not knock or push the device against steel or rusty iron. Do not drop the device.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 4.3.2 OPERATION WITHOUT FLUID Avoid running the pump so that it sucks in air (without fluid inside). The air, combined with the vapor of flammable fluids, can generate internal areas with an explosion hazard. Periodically check that the pump is working smoothly, paying special attention to the presence of air in the pumped fluid, which may be caused by damaged packings. Avoid operating the pump with damaged packings.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 5 DESCRIPTION 5.1 SCOPE OF DELIVERY Order No. 2301858 Designation Frame-mounted diaphragm pump Cobra 40-10 consisting of: Fluid section, air motor, connection elements The standard equipment includes: 322981 1 Sign 236219 1 Grounding cable, complete 341434 1 Double open-end wrench See Chapter 12.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL Description Air inlet (inside thread) Minimum Ø of the compressed air supply line Air consumption at 0.6 MPa; 6 bar; 87 psi per double stroke Sound pressure level at maximum permissible air pressure* Sound pressure level at 0.45 MPa; 4.5 bar; 65.27 psi air pressure* Sound pressure level at 0.3 MPa; 3 bar; 43.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 5.2.3 MEASUREMENTS AND CONNECTIONS B E D N G F P Cobra 40-10 F G A Q R C O B_02943 I B_04235 L H M K Measurement A B C D E F G H I K L M N O P Q R mm; inch 505; 19.88 313; 12.32 322; 12.68 134; 5.28 55; 2.16 182; 7.16 80; 3.15 M6 25; 0.98 G1/4" M36x2 NPSM1/4-18 149; 5.87 91; 3.58 107; 4.21 175; 6.89 7; 0.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 5.2.4 VOLUME FLOW Wagner AL nozzles inch mm Spray angle 0.007 0.009 0.011 0.013 0.015 0.017 0.019 0.021 0.023 0.025 0.027 0.029 0.031 0.035 0.043 0.052 0.18 0.23 0.28 0.33 0.38 0.43 0.48 0.53 0.58 0.64 0.69 0.75 0.79 0.90 1.10 1.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL Diagram for Cobra 40-10 Stroke frequency (DH/min) nl/min NL/min bar (MPa) 250 (25) 0 40 <3625> 80 120 160 200 240 1000 A <35> 200 (20) A <2900> 800 <28> B 150 (15) B 600 <21> C C 100 (10) 400 <1450> <14> 50 (5) 200 <725> <7> 0 0 0 B_01203 0.4 0.8 1.2 1.6 2 2.4 <0.1> <0.2> <0.3> <0.4> <0.5> <0.6> Air consumption Product pressure <2175> l/min L/min Water flow rate A = 6 bar (0.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 5.3 FUNCTION 5.3.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL WARNING Overpressure! Risk of injury from bursting components. Never change the safety valve setting. Fluid section (9) The fluid section has been designed as a double diaphragm pump with exchangeable inlet and outlet valves. Change between "spraying mode" and "circulation mode" using the relief valve (7). Positioning The Cobra pump may only be operated in a horizontal or vertical position as shown in the diagrams.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 5.3.2 1 2 3 4 5 PRESSURE REGULATOR UNIT FOR COBRA Pressure regulator Ball valve Pressure gauge Compressed air inlet AirCoat filter regulator Cobra (accessories) The AirCoat filter regulator must be mounted vertically in all installation positions for the diaphragm pump (see assembly manual for Filter Regulator, order number 2328614).
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 6 ASSEMBLY AND COMMISSIONING 6.1 INSTALLATION AND CONNECTION 6.1.1 INSTALLING THE PUMP Note: This pump can be used as part of a spraying system for Airless or AirCoat applications. The components can be found in the accessories list, provided that the system was not obtained as a spray pack. The nozzles must be selected according to the gun instructions. Procedure: 2 1 Mount the pump on a base frame, trolley (6), or wall mount.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 6.1.2 GROUNDING WARNING Discharge of electrostatically charged components in atmospheres containing solvents! Explosion hazard from electrostatic sparks. Only use a damp cloth to clean the piston pump. WARNING Heavy paint mist if grounding is insufficient! Danger of poisoning. Insufficient paint application quality. Ground all device components. Ground the work pieces to be coated.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Cable cross sections Pump Paint tank Conveyor Booth Spraying stand 4 mm2; AWG11 6 mm2; AWG10 16 mm2; AWG5 16 mm2; AWG5 16 mm2; AWG5 Procedure: 1 Screw on grounding cable with eye. 2 Clamp the grounding cable clip to a grounding connection on site. 3 Ground the product (paint) tank to an on-site grounding connection. 4 Ground the other parts of the system to an on-site grounding connection.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 6.2 COMMISSIONING 6.2.1 SAFETY INSTRUCTIONS Every time before starting up, the following points should be observed as laid down in the operating manual: - Observe all safety regulations in accordance with Chapter 4. - Carry out commissioning properly. WARNING High-pressure spray jet! Danger to life from injecting paint or solvent. Never reach into the spray jet. Never point the spray gun at people.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Before every start-up, the following points should be observed: - Secure gun with safety clip. - Check the permissible pressures. - Check all connecting parts for leaks. - Check hoses for damage. It should be ensured that the device is in the following state before carrying out any work on it: - The pressure should be released from the pump and high-pressure hose with gun. - The gun should be secured with the safety clip.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL Cobra EMERGENCY STOP In the event of unforeseen occurrences, the ball valve (1) should be vented immediately and the relief valve (2) opened.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 6.2.2 BASIC FLUSHING 1 Place empty tank (5) under return tube (4). 2 Place suction hose (7) in a tank with cleaning agent (6). 3 Adjust the pressure regulator (1) to approx. 0.05 MPa; 0.5 bar; 7.25 psi. 4 Open relief valve (3). 5 Slowly open the ball valve (2). 1 6 Adjust the air pressure on the pressure regulator (1) so that the pump runs smoothly. 7 Rinse the system until the cleaning agent that flows into the tank (5) is clean.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 6.2.3 FILLING WITH WORKING MATERIAL Positions of the ball valve 1 2 3 Open: working position Closed: The air motor can still be under pressure. Vent: Operating pressure in the air motor is vented (control pressure is still present). 3 2 1 B_04301 1 Place suction hose (7) and return tube (4) into the tank with the working material (6). 2 Adjust the pressure regulator (1) to approx. 0.05 MPa; 0.5 bar; 7.25 psi. 3 Open relief valve (3).
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 7 OPERATION 7.1 SPRAYING Positions of the ball valve 3 1 2 3 Open: working position Closed: The air motor can still be under pressure. Vent: Operating pressure in the air motor is vented (control pressure is still present). 2 1 1 2 Secure gun and place nozzle in the gun. Slowly open the ball valve. B_04301 3 Set the required working pressure on the pressure regulator. 4 Optimize the spraying results as laid down in the gun instructions.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 7.3 DECOMMISSIONING AND CLEANING Note: The device should be cleaned for maintenance purposes, etc. Ensure that no remaining product dries on and sticks to the device. Procedure: 1 Carry out work interruption -> refer to Chapter 7.2. 2 Carry out basic flushing -> refer to Chapter 6.2.2. 3 Maintain the gun according to the operating manual. 4 Clean and check the suction system and the suction filter. 6 Clean the outside of the system.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 8 TROUBLESHOOTING, MAINTENANCE, AND REPAIR 8.1 TROUBLESHOOTING AND RECTIFICATION Problem Pump does not work. Cause Air motor does not work or stops. No pressure indication on the pressure gage (air pressure regulator defective). Spray nozzle is clogged. Remedy Open and close ball valve on the pressure regulator unit or briefly disconnect compressed air supply. Disconnect compressed air supply briefly or repair or change pressure regulator.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Problem Pump runs fast when the spray gun is closed. Loss of power due to severe icing. Cause Valves worn. Remedy Replace the parts. There is a lot of condensation water Install a water separator. in the air supply. If none of the causes of malfunction mentioned are present, the defect can be remedied by a WAGNER Service Center.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 9 MAINTENANCE WARNING Incorrect maintenance/repair! Danger to life and damage to the device. Only a WAGNER service center or a suitably trained person may carry out repairs and replace parts. Only repair and replace parts that are listed in the "Spare Parts Catalogue" chapter and that are assigned to the device. Before all work on the device and in the event of work interruptions: - Disconnect the control unit from the mains.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 9.3 HYDRAULIC STAGE MAINTENANCE Dismount the device onto a stand as shown in the picture and turn it upside down. Observe the fill level marking (X) on the oil tank. 1 B_04241 B_04242 9.3.1 1 2 CHECKING THE OIL LEVEL Start up the pump for a short time without any product. Then read oil level A. A max. X Dismount the device onto a stand as shown in the picture and turn it upside down. Observe the fill level marking (X) on the oil tank.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 9.3.2 CHANGING THE OIL The oil should be changed after 500 service hours or once a year. Necessary accessories: Order No. 322911 Oil filling set NOTICE Using hydraulic oil Using the wrong hydraulic oil can cause a malfunction. Use only original hydraulic oil - Wagner Order No. 322912 (250 ml or 15 cu inch). Discharging oil Procedure: 1 Decommission and clean the device -> follow Chapter 7.3 up to and including point 6.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL CAUTION Environmental pollution caused by waste oil! Waste oil in the sewage network or spilled on the ground causes severe environmental damage. Groundwater pollution is liable to prosecution. Collect waste oil and bring it to a collection point. Waste oil is taken back by the seller when purchasing hydraulic oil. Filling hydraulic stage with oil Procedure: 1 Turn pump (mounted on the base frame) upside down.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL Vent Procedure: 1 Turn the pump upside down. Remove the threaded plug (5). 2 Slowly start up (vent) the pump until no air bubbles appear from the oil suction fitting. 3 Oil level A in the oil tank has to be within the specified markings (X). 4 Screw in threaded plug (5) and tighten with 2 Nm; 1.5 lbft. 5 Mount piston cover (1) and hood with casing. 6 The device is ready for operation again.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 10 ACCESSORIES 10.1 COBRA 40-10 ACCESSORIES Accessories list for Cobra 40-10 Order No. Designation A 2301858 Diaphragm pump Cobra 40-10 1 322912 Hydraulic oil (for pressure stage) 250 ml; 250 cc 2 236219 Grounding cable 3 m; 9.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 4 Cobra 40-10 1 3 AirCoat 2 A 53 51 52 7 12 16 17 13 14 15 11 24 25 B_04234 20 21 B_04285 43
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 11 SPARE PARTS 11.1 HOW CAN SPARE PARTS BE ORDERED? Always supply the following information to ensure delivery of the right spare part: Order number, designation, and quantity The quantity need not be the same as the number given in the " " column in the lists. This number merely indicates how many of the respective parts are used in each component.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 11.2 OVERVIEW OF THE COBRA 40-10 COMPONENTS 1 1 2 1 3 1 4 1 5 1 6 3 7 4 8 1 9 1 10 4 11 2 12 1 13 1 14 1 15 1 16 1 17 1 = Wearing parts Order No.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 11.3 COBRA 40-10 AIR MOTOR Order No. Designation 1 1 9998718 Drive fastener 2 1 367318 Shoulder screw 4 3 1 9925033 Washer 4 1 367311 Hood 4 5 1 367319 Sound absorbing mat 4 6 1 9999152 Velcro fastener coating part 7 1 9999151 Velcro fastener adhesive part 8 1 367318 Shoulder screw 4 9 1 9925033 Washer 10 1 367310 Silencer 4 11 1 9974098 O-ring 12 1 9974097 O-ring 13 3 9900325 Socket cap screw 14 3 9920103 Washer A6.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 1 2 3 Cobra 40-10 60 10-15 Nm; 7-11 lbft 60 * 4 7 6 5 54 53 8 20-25 Nm; 15-18 lbft 9 58 10 58 11* 12* 13 14 2-3 Nm; 1.5-2.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 1 4 2 1 1 1 1 2 1 1 1 1 1 2 6 1 1 1 Order No.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 49
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 11.4 COBRA 40-10 FLUID SECTION 7 51 53 111 54 55 53 70 57 60 7 62 109 61 59 29 59 63 111 34 30 31 33 32 35 B_04252 Notes: The piston rod (25) may only be mounted with the screwed-on assembly pin (108). 108 Grease all o-rings and seals lightly with grease (111) before mounting them. Cobra 40-10 fluid section Order No.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 1 2 3 Cobra 40-10 4 89 90 5 70 Nm; 52 lbft 110 6 7 105 110 90 Nm; 66 lbft 8 9 13 112 17 110 10 78 11 110 20 Nm; 15 lbft 14 78 15 103 19 93 110 98 50 Nm; 37 lbft 16 91 110 100 30 Nm; 22 lbft 99 96 94 95 97 18 69 20 23 22 21 110 92 24 25 27 102 26 66 67 40 Nm; 29.5 lbft 67 101 26 102 27 42 38 40 2 Nm; 1.5 lbft 35 110 50 34 32 33 31 46 47 49 41 20 Nm;14.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Cobra 40-10 fluid section Order No. Designation 6 8 9907234 Hexagon screw 7 10 9920107 Washer 8 2 9974184 O-ring 9 2 322411 Valve fitting 10 2 341336 Clasp 1 322914 Inlet valve set, complete (comprising 2 valves), see Chapter 11.9 11 13 1 2330810 Connection piece 14 1 322410 Fluid section 15 2 322412 Plug 16 2 9904311 Screw plug 17 1 169248 Relief valve, complete, see Chapter 11.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Cobra 40-10 fluid section Order No.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 11.9 COBRA 40-10 INLET VALVE Order No.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 11.11 RELIEF VALVE Order No. 1 1 169248 2 1 9920602 3 1 169346 4 1 9920202 5 1 9971395 1 9971486 6 7 1 9992528 8 1 9971367 = Wearing parts Designation Relief valve, complete Adjusting washer Pressure spring Washer O-ring 10x1.25 O-ring 4x2 Loctite 270 50 ml; 50 cc Spiral baking ring 4.78x1.78 1.5 Thread: Pretreated with fast cleaner 7 Loctite type 7063.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 11.12 COBRA 40-10 FRAME, COMPLETE Order No. 1 1 322052 2 1 322442 3 1 322443 4 2 9990861 5 4 9999209 6 2 9910204 7 2 9900202 8 4 9900126 = Wearing parts Designation Base frame Cobra 40-10 Base frame pressed Frame pipe Plug Saddle feet for round tubes Self-locking hexagon nut, M6 Hexagon screw M6x40 Hexagon screw M6x45 2 6 4 8 3 5 7 1 B_02292 11.13 HOPPER, COMPLETE Order No.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 11.14 TROLLEY 15 5 17 10 2 13 14 4 9 5 16 6 1 3 7 8 A B Distance: 11 1 1 2 1 3 1 4 4 5 6 6 2 7 4 8 4 9 1 10 2 11 2 12 2 13 2 14 4 15 1 16 2 17 2 = Wearing parts Order No.
ORDER NUMBER DOC 2303675 VERSION 10/2013 OPERATING MANUAL 11.16 SMALL QUANTITY CUP Order No. Designation 1 2321424 1 1 2320844 2 1 2321426 3 1 2320841 4 2 2321427 2 2321676 5 6 1 2320888 7 1 2320870 1 2320922 8 9 1 2322857 10 1 2322671 = Wearing parts Sealing plug Small quantity cup Union nut with bayonet Low-pressure mini ball valve G1/2 Gravity feed cup adapter HSM Gravity feed cup SPA easy line TA Sieve insert SPA easy line Cone connector preassembled Sealing washer Sealing sleeve Relief tube 0.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 12 3+2 YEARS GUARANTEE FOR PROFESSIONAL FINISHING 12.1 SCOPE OF GUARANTEE All Wagner professional colour application devices (hereafter referred to as products) are carefully inspected, tested, and subject to strict checks under Wagner quality assurance.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 12.4 EXCLUSION OF GUARANTEE Guarantee claims cannot be considered for parts that are subject to wear and tear due to use or other natural wear and tear, as well as defects in the product that are a result of natural wear and tear, or wear and tear due to use. This includes in particular cables, valves, packings, nozzles, cylinders, pistons, means-carrying housing components, filters, pipes, seals, rotors, stators, etc.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL 12.
VERSION 10/2013 ORDER NUMBER DOC 2303675 OPERATING MANUAL Service Network in Germany Berlin Stuttgart Tel. Fax Tel. Fax Grünstadt Munich Tel.: +49 (0) 63 59/ 87 27 55 0 Fax: +49 (0) 63 59/ 80 74 80 Ratingen Tel:. +49 (0) 89 /6 14 00 22 Fax: +49 (0) 89 / 6 14 04 33 Nuremberg Tel.: +49 (0) 21 02 / 3 10 37 Fax: +49 (0) 21 02 / 3 43 95 Tel.: +49 (0) 91 22 / 7 94 73 Fax: +49 (0) 91 22 / 7 94 75 0 Heidersdorf in Sachsen Hannover Tel.: +49 (0)3 73 61 / 1 57 07 Fax: +49 (0)3 73 61 / 1 57 08 Tel.
ED FI CERT A I DK Tel. Fax B GB Tel. Fax E Tel. Fax CH I Tel. Fax F Tel. Fax D Fax Tel. Fax NL Tel. Fax Tel. Fax CZ S Tel. Fax Tel. Fax Tel.: +49 (0) 75 44 / 505 -1664 Fax: www.wagner-group.com Subject to changes and errors.
