Installation & Assembly

ManualsBrandsWade Logan ManualsCeiling LightsDowney 1-Light Single Cylinder Pendant

1of2

Assembly Instruction

Package Contents

Crossbar Assembly

6” Rod

12” Rod

12” Rod with Nipple

STEP 1 - Install Bulbs and Shade

IMPORTANT:

A. This fixture uses G9 Xenon clear

bulb (K). Maximum 60 watts.

Insert bulb and push snugly into

place.

B. Place Inner Shade (K) over the

Socket Assembly (F), line up the

hole on the Inner Shade (H) and

the mounting hole on the Socket

Assembly. Threading Long Stick

(G) into the mounting hole, tighten

until sung.

C. Place Outer Shade (I) over the

Inner Shade (H), line up the hole

on the Outer Shade (I) and the

mounting hole on the Long Stick

(G). Threading Short Stick (J) into

the Long Stick (G), hand tighten

until sung.

Do not touch the

bulb with bare hands use a cloth or

glove.

Ceiling

Canopy

Figure 1

Socket

Assembly

Long

Stick

Inner

Shade

Outer

Shade

Short

Stick

(1)G9XenonClearbulb(supplied),60WMaximumLightSource:

ToolsRequired:Flatheadscrewdriver, Phillips screwdriver,pliers,wirecutters,wirestrippers,electricaltape,safetyglasses.

Preparation:Identifyandinspectallpartsbeforebeginninginstallation.Checkpackagecontentlistanddiagramsbelowtobesureallpartsare

present.Ifanypartsaremissingordamaged,donotattempttoassemble,install,oroperatethefixture.Contactcustomerserviceforreplacement

parts.

EstimatedAssemblyTime:30-45 minutes

Warnings and Cautions

Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.

These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly

recommend that a licensed, professional electrician perform the installation.

Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject

glass parts to any shock while in operation or shattering may result.

Do not touch the bulb with bare hands use a cloth or glove.

G9 Xenon

Clear Bulb

STEP 2 - Install Ceiling

Canopy, Rods and Socket

Assembly together

A. Determine the Rods (B/C/D)

to be assembled to the Socket

Assembly with Shades

according to your hanging

height.

B. Pass the supply wires and

ground wire through the

chosen rods (B/C/D) and the

Ceiling Canopy (E). Thread

the Socket Assembly with

Shades, the chosen Rods

(B/C/D) and the Ceiling

Canopy (E) together. Hand

tighten until snug.

Suggested rods for Ceiling

height :

8’ ceiling : use (2) 12” rods

9’ ceiling : use (2) 6” rods and

(2) 12” rods

Supply Wires

and Ground Wire

Figure 2

Socket Assembly

with Shades

STEP 3 Install Crossbar Assembly-

A. Pass the supply wires through the

Crossbar Assembly (A). Attach the

Crossbar Assembly (A) to the Outlet Box

with the head of the Green Ground Screw

facing you. Secure it with Outlet Box

Screws (not included). Tighten until snug.

Supply Wires

with Ground Wire

Outlet Box Screws

(not included)

Outlet

Box

Figure 3

STEP 4 Fit Ceiling Canopy to

Crossbar Assembly

Ceiling Canopy to the

Ceiling Canopy

ceiling

Remove mounting balls from the

Crossbar Assembly (A). Fit the

(E)

Crossbar Assembly (A) and

secure with mounting balls. Note:

The (E) should be

snug against the and the

Mounting

Screw

Hex Nut and

Lock Washer

Mounting Ball

mounting balls. If not, adjust the length of the nipple on the Crossbar

Assembly (A) by unscrewing the preassembled hex nut and lock

washer and then screwing the mounting screws in or out of the

Figure 3

Summary of content (2 pages)

PAGE 1
Assembly Instruction Tools Required: Flathead screwdriver, Phillips screwdriver, pliers, wire cutters, wire strippers, electrical tape, safety glasses. Light Source: (1) G9 Xenon Clear bulb (supplied), 60W Maximum Estimated Assembly Time: 30-45 minutes Preparation: Identify and inspect all parts before beginning installation. Check package content list and diagrams below to be sure all parts are present. If any parts are missing or damaged, do not attempt to assemble, install, or operate the fixture.
PAGE 2
crossbar until the correct length is achieved. Once the Ceiling Canopy (E) is secure, remove the mounting ball and Ceiling Canopy (E) and proceed to Step 5. STEP 5 - Wire Connections A. Use standard wire connectors (not included) to make all wire connections. (Connectors are not included with fixture.) Twist connectors until wires are tightly joined together. Wrap each connection with approved electrical tape and carefully stuff all the connected wires into the Outlet Box. STEP 6 - Install Fixture Body A.