Owner Manual

ITEM NO: 60-6624
ARTÍCULO Nº: 60-6624
ARTICLE N°: 60-6624
INSTALLATION AND SAFETY INSTRUCTIONS
FOR YOUR SAFETY
WARNING: BE SURE THE ELECTRICITY TO THE WIRES YOU ARE
WORKING ON IS SHUT OFF; EITHER THE FUSE IS REMOVED OR
THE CIRCUIT BREAKER IS SHUT OFF.
GENERAL
You don’t need special tools to install this xture. Be sure to follow
the steps in the order given. Under no circumstances should a xture
be hung on house electrical wires, nor should a swag type xture be
installed on a ceiling which contains a radiant type heating system.
Read instructions carefully. If you are unclear as to how to proceed,
consult a qualied electrician.
NOTE: Proper wiring is essential for the safe operation of this xture.
FIXTURE ASSEMBLY
Carefully remove the xture from the carton and check that all parts
are included as shown in gure. Be careful not to misplace any of the
screws or parts, which are needed to install this xture.
INSTALLATION
IMPORTANT: Do not attach xture directly to outlet box.
Installation for SEMI-FLUSH:
STEP 1: Thread mounting screw into the matching hole of cross bar.
STEP 2: Secure the cross bar to outlet box with outlet box screws.
STEP 3: Tie the ground wires from xture and from outlet box to the
ground screw on the mounting strap.
STEP 4: Place the canopy to the outlet box by aligning the protruding
mounting screws all the way through the canopy and tighten the xture
using lock nuts provided until xture body is held rmly.
Installation for HANGING PENDANT:
Follow STEP 1 and STEP 2 (above).
STEP 3: Fasten the loop to the nipple. Fill holes of the canopy with
the Screws and Lock Nuts provided in the pendant hardware kits.
STEP 4: Using two pliers, twist open links at two ends of the chain as
show. Hook one link to the loop and the other link to the screw collar
loop. Close the links. Place a piece of cloth between the pliers jaws
and the chain link to prevent scratching the link nish.
STEP 5: Weave xture wires up through the loop, through the chain,
through the ring, through the screw collar loop and through the canopy
and through the nipple on the mounting strap.
GROUNDING INSTRUCTIONS
STEP 1: Insert the green grounding screw into the hole with two raised
dimples on the mounting bar. Wrap the ground wire from the xture (if
supplied) around the green grounding screw, then connect it to ground
wire from the outlet box (if not xed on the outlet box) using a wire
connector (not supplied). If ground wire from the xture is not supplied,
wrap the ground wire (if not xed on the outlet box) from the outlet box
around the green grounding screw and tighten it.
NEVER CONNECT GROUND WIRE TO BLACK OR WHITE
POWER SUPPLY WIRES.
STEP 2: Take note of the color of the wire(s) on your xture. Identify
which group your xture wire(s) falls into and connect the wires
according to the directions below:
GROUP A:
Connect to Black House Wire
GROUP B:
Connect to White House Wire
BLACK WHITE
* PARALLEL WIRE (round & smooth) * PARALLEL WIRE (square & ridged)
WHITE OR GREY WITH TRACER WHITE OR GREY WITHOUT TRACER
BROWN, GOLD OR BLACK
WITHOUT TRACER
BROWN, GOLD OR BLACK
WITH TRACER
NOTE: When parallel wire (SPT-I & SPT-2) is used, the tracer wire is
square shaped or ridged and the less tracer wire is round in shape or
smooth (seen best when viewed from wire end.)
STEP 3: Take your xture wire(s) from group A and place evenly against
the black wire from the outlet box. Do NOT twist wires together before
using wire connectors.
STEP 4: Fit a wire connector over the wires and screw the connector
clockwise until you feel rmness.
STEP 5: Try gently to pull the connector off the wires. If you can pull the
connector off, carefully re-do steps 3 and 4 as above, and check again
for a rm connection.
STEP 6: Connect the xture wire from group B to the white wire from
the outlet box in the same manner. Make sure no bare wires can be
seen outside wire connectors.
FINAL ASSEMBLY
STEP 1: After wires are connected, tuck them carefully inside outlet
box. Raise canopy allowing the mounting screw to protrude through
the hole in the canopy, and secure with ball nuts.
STEP 2: Install lamps (not included). Do not exceed the maximum
capacity recommended on the socket.
CLEANING
To clean, wipe xture with a soft cloth. Clean glass with a mild soap.
Do not use abrasive materials such as scouring pads or powders, steel
wool or abrasive paper.
ORDERING PARTS
Keep this sheet for future reference, and in case you need to order
replacement parts. Be sure to use exact wording from illustration when
ordering parts.
FIGURE
Line art shown may not exactly match the xture enclosed. However, the installations
do apply to this xture.
La ilustración puede no concordar exactamente con la pieza enviada. Sin embargo,
las instalaciones sí aplican para esta pieza.
Les images peuvent ne pas correspondre exactement au luminaire de la boîte.
Par contre, les directives d’installation s’appliquent au luminaire.
Mounting Screw
Ball Nut
Outlet Box
White Wire Connection
Universal Circle Cross Bar
Outlet Box Screw
Canopy
Black Wire Connection
Ground Screw
The xture can be assembled as SEMI-FLUSH or HANGING PENDANT.
If assembling as hanging pendant, the consumer needs to buy the pendant hardware kits separately.