Navigation Contents USER’S MANUAL USB FOR WINDOWS AND MACINTOSH Index
WACOM PenPartner User’s Manual for USB (Windows and Macintosh), February 03, 1999 International English V1.0 for USB Copyright WACOM Company, Limited, 1999 All rights reserved. No part of this manual may be reproduced except for your express personal use. WACOM reserves the right to revise this publication without obligation to provide notification of such changes.
RADIO AND TELEVISION INTERFERENCE The equipment described in this manual generates, uses, and can radiate radio-frequency energy. If it is not installed and used properly—that is, in strict accordance with WACOM instructions—it may cause interference with radio and television reception. FCC NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device in accordance with the specifications in Part 15 of FCC rules.
CE DECLARATION The PenPartner digitizing tablet, model CT-0405-U, has been tested by the TÜV Rheinland in Japan (an accredited EMC laboratory) and found to comply to the following harmonized European Norms: • EN 50 082-1 (electromagnetic immunity) • EN 55-022 Class B (electromagnetic emissions). Based on the results of these tests, WACOM declares that the above mentioned devices conform to Article 10.1 of the European Council Directive 89/336/EEC and indicates this conformity by the CE-sign on each device.
NAVIGATING THE MANUAL Use the navigation controls to move through the manual: Go to front page. Contents Index Go to Table of Contents. Go to Index. Go to Navigating the Manual. Page back, or page forward. HEADING TEXT Go to beginning of section. Text Go to topic. Topic section continued. The Acrobat Reader provides you with additional tools for using and printing the manual. Refer to the Acrobat Reader Online Guide for more information.
ABOUT THE MANUAL This combined interactive User’s Manual for Windows and Macintosh provides quick access to information about PenPartner. Just click on a navigation button or highlighted word to move through the document. The information is common to both platforms, unless otherwise noted. Windows screen captures are shown. • The Table of Contents enables you to go directly to a topic by clicking on it. • Installation shows you how to install the hardware and software.
Certain kinds of information are not included in this manual. • Information about your specific computer hardware. • Information about your operating system. • Information about application software. To use the pressure-sensitive UltraPen with your favorite drawing application, refer to instructions in that application’s manuals. You can find information about pressure-sensitive and eraser-aware applications at WACOM’s web site (see Product information). • Information about other WACOM tablets.
TABLE OF CONTENTS Trademarks Radio and television interference FCC Notice CE Declaration BZT Notice Navigating the manual About the manual Caring for PenPartner Replacing the pen tip CUSTOMIZING PENPARTNER Opening the control panel Customizing the pen Adjusting tip feel Make double-clicking easier Adjusting eraser feel Choosing pen or mouse like movement Simulating mouse buttons Simulating keyboard modifier keys Returning to default settings INSTALLATION PenPartner box contents Windows installation Macin
Troubleshooting tables General problems Windows-specific problems Macintosh-specific problems Application-specific problems Contacting technical support Linking to the Web page Pre-contact checklist Who to call USA, Canada, Central and South America Europe, Middle East and Africa Japan Asia Pacific Parts and accessories Tablets Pens Other parts and accessories GLOSSARY INDEX APPENDICES Uninstalling the software Product specifications PenPartner tablet (Model CT-0405-U) UltraPen (Model UP-703E) License an
INSTALLATION PenPartner is compatible with all Windows and Macintosh applications that support a mouse. If you have not already done so, now is a good time to check the PenPartner box contents. The PenPartner CD-ROM contains a Readme file with late-breaking news, this User's Manual, and software drivers that enable your computer and tablet to communicate. You can install PenPartner even if you already have a mouse or trackball; the tablet can be used alone or with your other pointing devices.
PENPARTNER BOX CONTENTS You should find the following items in your PenPartner box: Registration Card Spare Nib CD-ROM UltraPen (UP-703E) Pen Stand Tablet (CT-0405-U) Illustrations not to scale.
WINDOWS INSTALLATION To use PenPartner, you must install the tablet software from the PenPartner CD-ROM. When installing PenPartner, you may be prompted to install some Windows system files. Please have your Windows system disc available. 1. Turn your computer on. After Windows has started, insert the PenPartner CD-ROM into your computer. 2. Plug the PenPartner USB connector into an active USB port. The PenPartner LED will light. If the LED does not light, your computer may not be USB Ready. 3.
MACINTOSH INSTALLATION 1. Plug the PenPartner USB connector into an active USB port on your computer or an active USB hub. 2. If your computer is off, turn it on now. The tablet LED will light to indicate PenPartner has registered as a USB device. If the LED does not light, your USB port may not be functioning properly; go to Having Trouble? PenPartner is working in mouse emulation mode. You should now be able to use your UltraPen on the tablet to move the screen cursor.
MAIL IN REGISTRATION Please complete and mail in the WACOM Registration Card that came with your tablet. PRODUCT INFORMATION To learn more about which software applications currently support PenPartner, visit the WACOM web site for your region: USA, Canada, Central and South America Europe, Middle East and Africa Japan Asia Pacific (English) Contents Index http://www.wacom.com/productinfo http://www.wacom.de/productinfo http://tablet.wacom.co.jp http://www.wacom.co.
USING PENPARTNER The quickest way to learn about PenPartner is to become familiar with its appearance and features. As you explore, you will find the UltraPen easy to use for drawing and erasing, or as a mouse substitute. PenPartner can be used in all applications that support a mouse.
APPEARANCE AND FEATURES The PenPartner tablet and UltraPen include a variety of features.
USING THE ULTRAPEN Think of the tablet’s active area as a mapped representation of your computer screen. Wherever you place the UltraPen on the tablet’s active area, the screen cursor will jump to the corresponding point on the screen. For example, when you position your pen tip in the upper right corner of the tablet, the cursor appears in the upper right corner of your screen. This is called “absolute positioning,” and makes tracing possible—something you cannot do with a mouse.
POINTING The UltraPen controls a pointer (or cursor) on your screen. Screen cursors have different shapes, such as an arrow or I-beam, depending on the type of application you are running. Move the screen cursor by lifting the UltraPen and placing it at a new location on the tablet. The cursor instantly jumps to the new location (absolute positioning).
CLICKING Clicking. To click, tap the tablet once with the tip of the UltraPen, or touch the pen to the tablet with enough pressure to simulate pressing a mouse button. Double-clicking. To double-click, quickly tap the tablet twice in the same place with the pen tip. This is like clicking twice with a mouse button. Be sure to hold the UltraPen so that you press downward on the pen tip. Hint: You may find it easier to set the side switch to double-click automatically when pressed.
DRAGGING Dragging means moving a selected (highlighted) object on the screen. Point to the object, then press the UltraPen to the tablet and drag the pen along the tablet’s active area. The selected object will move across the screen. To select text with this method, move the screen cursor to the beginning of some text then press and drag the UltraPen across the tablet until the text is highlighted.
PROXIMITY The tablet can recognize the UltraPen’s position whenever it is within proximity, 5 mm (.2 inch), above the tablet’s active area. This enables you to trace a drawing or photograph as long as the pen tip remains within proximity height. Also, you do not have to touch the pen tip to the tablet in order to position the screen cursor or use the side switch. 5 mm (.
DRAWING WITH PRESSURE The UltraPen responds to the nuance and inflection of your hand movements, enabling you to create natural-looking pen and brush strokes. Many graphics applications have drawing tools that respond to the pressure you place on the UltraPen. For example, in some drawing programs sliders are used to vary brush characteristics (width, color, jitter, opacity, and graininess). These characteristics can be controlled by the UltraPen’s pressure sensitivity.
ERASING WITH EASE The eraser on the UltraPen works like the eraser on a pencil. In graphics applications that support the UltraPen’s eraser, you can erase intuitively and naturally—without manually selecting another tool. The eraser-aware application will automatically switch to the eraser tool. PenPartner will also erase in some non-graphics applications; though not pressure-sensitive you can use the eraser to select and delete text.
CARING FOR PENPARTNER Regular cleaning with a soft, damp cloth will help prolong the life of your tablet surface and pen tip. You can also use a very mild soap (such as dishwashing liquid) diluted with water. Do not use volatile liquids, such as paint thinner or benzene, because they may damage the plastic case. Keep the tablet in a clean, dry place and avoid extremes in temperature. Room temperature is best.
CUSTOMIZING PENPARTNER After you master the basics of using the tablet, you may want to customize the way your UltraPen works. Use the control panel to adjust the tip feel, simulate mouse buttons, or to change a variety of other settings.
OPENING THE CONTROL PANEL You customize your pen and tablet from the PenPartner control panel. For Windows: Open the Control Panel window by clicking on the Windows Start button. Then select Settings and Control Panel, and double-click on the PenPartner icon. Or... For Macintosh: From the Apple menu, choose Control Panels and double-click on the PenPartner icon. Double-click here to open the PenPartner control panel. Windows Control Panel shown above.
CUSTOMIZING THE PEN PenPartner’s control panel allows you to customize your pen and tablet. Balloon Help, which provides quick information and useful tips, is available for most control panel items. Software driver version. Returns control panel settings to factory defaults. Customizes amount of pressure needed to erase with the UltraPen. Closes control panel. Selects side switch function. Customizes amount of pressure needed to click or draw with the UltraPen.
ADJUSTING TIP FEEL The Tip Feel slider adjusts the sensitivity of the UltraPen tip. With one easy adjustment, you can set the UltraPen for the tip feeling you prefer when clicking or drawing pressure-sensitive lines. To set the amount of pressure needed to click or draw: In the PenPartner control panel, drag the Tip Feel slider to one of the five settings from Soft to Firm. Your changes take effect immediately.
MAKE DOUBLE-CLICKING EASIER Double-clicking with a pen is somewhat different than with a mouse. To double-click, quickly click twice on the same screen pixel. To make double-clicking easier: expand the tap area that accepts a double-click (the double-click distance), or set the pen’s side switch to automatically double-click when pressed.
ADJUSTING ERASER FEEL The UltraPen’s eraser is pressure sensitive, enabling you to erase naturally and expressively. Eraser Aware. Applications that support the UltraPen’s eraser are called eraser-aware. They take advantage of the pen’s eraser in different ways, depending on what makes sense for the application. Context Aware. When you use the eraser to select text or objects, PenPartner automatically senses whether the screen cursor is over an object that can be erased.
CHOOSING PEN OR MOUSE LIKE MOVEMENT You can choose how the screen cursor reacts to the motion of your UltraPen on the tablet: Pen Mode. When you select Pen Mode, the tablet acts as a mapped representation of your computer screen. Wherever you place the UltraPen on the tablet, the cursor jumps to the same corresponding point on the screen. This is called “absolute positioning.” Mouse Mode.
SIMULATING MOUSE BUTTONS You can set the side switch on the UltraPen to simulate mouse button functions. To simulate mouse buttons: 1. In the PenPartner control panel, open the side switch function pull-down menu. 2. Select a click option from the menu. Your changes take effect immediately. For Windows: Select Left Click, Left Double Click, Left Click Lock, Right Click, or Middle Click. For Macintosh: Select Click, Double Click, or Click Lock.
SIMULATING KEYBOARD MODIFIER KEYS Many applications use modifier keys to constrain sizing or the placement of objects. You can set the side switch on the UltraPen to simulate holding down the Shift, Ctrl, Alt, Option (Macintosh only), or Command (Macintosh only) modifier keys. To simulate keyboard modifier keys: 1. In the PenPartner control panel, open the side switch function pull-down menu. 2. Select Modifiers... from the menu.
RETURNING TO DEFAULT SETTINGS You can return to the tablet default settings at any time. In the PenPartner control panel, click on the Default button. Your changes take effect immediately. Returns control panel settings to factory defaults. Your tablet and UltraPen are now set to their original default conditions.
HAVING TROUBLE? Most of the time your tablet will work flawlessly. But if you are having trouble, WACOM recommends you do the following: 1. Refer to the troubleshooting procedures described in this chapter. 2. Look in the troubleshooting tables. Your problem may be described there and you can try the solution offered. 3. Open the PenPartner Readme file for late-breaking information. 4.
TROUBLESHOOTING WINDOWS TROUBLESHOOTING MACINTOSH TROUBLESHOOTING WINDOWS TROUBLESHOOTING If the PenPartner LED does not light after plugging in PenPartner, see the sections below: Checking USB cable connection(s), PCs, Verifying your computer is USB ready, and Testing the hardware, PCs. Checking USB cable connection(s), PCs Make sure your computer is turned on and the operating system has finished loading. 1. Verify that the USB cable is securely connected to a USB port. 2.
Verifying your computer is USB ready PenPartner requires Windows 98. Many PCs that shipped with Windows 95 have the USB port disabled in the BIOS. If you upgraded to Windows 98, verify that the USB ports are enabled in the BIOS and that all necessary system software has been installed. Refer to your system documentation or contact your system manufacturer for information on enabling USB support for your computer.
4. Now, without applying pressure to the pen tip, press the side switch; the status LED should again change from orange to green. 5. Turn the pen over; the status LED should change from orange to green when the eraser enters proximity. If any of the above tests failed, you may have a defective pen or tablet. See Contacting technical support.
Verifying your Macintosh is USB ready If the tablet LED does not light, your computer may not have the necessary USB software installed, or may not be configured properly. • If you have an iMac, you will need Macintosh OS 8.5, Mac OS ROM 1.2.1, and iMac Update 1.1 (located on the PenPartner CD-ROM). • If you added a USB interface card you must also install system software to support the USB card. • Otherwise, if your computer came from the factory with a USB port installed, it should be USB ready.
4. Now, without applying pressure to the pen tip, press the side switch; the status LED should again change from orange to green. 5. Turn the pen over; the status LED should change from orange to green when the eraser enters proximity. If any of the above tests failed, you may have a defective pen or tablet. See Contacting technical support. Resolving software conflicts If the WACOM tablet icon appears with a red X through it when starting your computer, the WACOM tablet driver failed to load properly.
3. Try changing the loading order of the tablet driver. Place a space before the name “Tablet Driver” in the Extensions folder. This causes the PenPartner driver to load earlier than other control panels. Restart your computer and watch for the WACOM tablet successful startup icon. 4. If the PenPartner driver still does not load, locate the conflicting extension in the System Folder. • Go to the System Folder and create a new folder titled, “Disabled Extensions”.
5. If the PenPartner driver still does not load, locate the conflicting control panel. • Go to the System Folder and create a new folder titled, “Disabled Control Panels”. Drag your third-party control panels to this new folder. • Restart your computer. If you see the successful startup icon, you have a conflict with one of the control panels. If the PenPartner driver still does not load, drag your third-party control panels back to the Control Panels folder and delete the Disabled Control Panels folder.
TROUBLESHOOTING TABLES If you encounter problems with your UltraPen or tablet, refer to the following tables. Your problem may be described here, and you can try the solution offered. Be sure to see the tables both for general problems and for your specific platform. If you have difficulty in an application, you can check the table for application-specific problems.
Double-clicking is difficult. The tip switch does not function. The side switch does not work. Be sure you are quickly tapping the tablet twice in the same place on the tablet’s active area. WACOM recommends using the side switch to double-click (review the technique in Clicking). Try increasing the Double Click Distance (see Make double-clicking easier). Try using a lighter Tip Feel (see Adjusting tip feel). Refer to Testing the hardware, PCs or Testing the hardware, Macintosh.
Pen selects everything or will not stop drawing. Eraser selects everything or will not stop erasing. There is a delay at the beginning of pen strokes when using the UltraPen for drawing or selecting. You have to press hard with the pen when clicking or drawing. Try increasing the pen tip click pressure in the PenPartner control panel by moving the Tip Feel slider toward Firm. Refer to Testing the hardware, PCs or Testing the hardware, Macintosh.
The screen cursor jumps back when using a mouse. Cannot move the cursor where you want to on the screen, or the line you are drawing does not line up with the location of the pointer in paint applications. When your pen is not in use, place it in the pen stand or some location near the tablet, but not on the tablet. Leaving your pen on the tablet may interfere with screen cursor positioning when using other input devices. Open the PenPartner control panel and verify that Pen Mode is selected.
WINDOWS-SPECIFIC PROBLEMS The PenPartner LED is on but the UltraPen does not move the screen cursor. After changing the display resolution, part of the tablet or display is unreachable. The UltraPen does not control the screen cursor when using a full screen DOS window in Windows 98. After pressing Ctrl+Alt+Del, the screen cursor cannot be controlled with the UltraPen. The Windows HID driver was installed. Run Setup from the PenPartner CD-ROM and install the PenPartner driver software.
When the pen tip contacts the tablet surface, the cursor jumps to the top left corner of the screen, or the error message, “Unable to implement function”, appears within the PenPartner control panel. You may have had another manufacturer’s tablet, and the drivers are still loaded on your system: ACECAT: Edit your SYSTEM.INI. Go to the drivers=line in the [boot] section and remove awintab. Then go to the [drivers] section and remove the awintab=awintab.drv line.
APPLICATION-SPECIFIC PROBLEMS MetaCreations Painter: Versions of Painter older than V5.0.3 (running on Windows 98) may have intermittent problems with pressure not functioning. MetaCreations Expression: Versions of Expression older than V1.0.5 (running on Windows 98) may have intermittent problems with pressure not functioning. Microsoft Access V2.0 for Windows: Using the pen to click or double-click in a field causes the screen cursor to freeze. Upgrade to Painter V5.0.3 or greater.
CONTACTING TECHNICAL SUPPORT If you have a problem with your WACOM tablet, first check Installation and Having Trouble? to be sure the tablet is installed correctly. If you cannot find the answer in this manual, you may find updated information about your problem in the Readme file located on the PenPartner CD-ROM. Check also the WACOM Home Page on the Internet. If you are unable to solve the problem, contact WACOM Technical Support.
WHO TO CALL If you think your WACOM tablet is not working properly, contact the WACOM support staff for the area where your product was purchased. If you have a modem, you can download the latest software drivers from the Internet or the WACOM bulletin board. USA, Canada, Central and South America Contact your local distributor, or: Worldwide Web: http://www.wacom.com/productsupport Anonymous FTP Site: Phone: ftp.wacom.
Europe, Middle East and Africa Contact your local distributor, or: Worldwide Web: Anonymous FTP Site: Phone (Austria): Phone (Belgium): Phone (France): Phone (Germany): Phone (Great Britain): Phone (Italy): Phone (Netherlands): Phone (Switzerland): Phone (other countries): FAX: Internet email: http://www.wacom.de ftp.wacom.
Japan Contact your local distributor, or: Worldwide Web: http://tablet.wacom.co.jp Phone: FAX: Internet email: ++81-(0)3-5322-3905 ++81-(0)3-5322-3916 tablet@wacom.co.jp Software updates and information. (Japanese) Technical Support. (Japanese) Technical Support. (Japanese) Technical Support and sales. (Japanese) Asia Pacific Contact your local distributor, or: Worldwide Web: http://www.wacom.co.jp/asia-pacific Phone: FAX: Internet email: ++81-(0)480-78-1213 ++81-(0)480-78-1217 asia-pacific@wacom.
APPENDICES A procedure for uninstalling the PenPartner software is included in this section. You will also find product specifications, license and warranty information, and a list of available parts and accessories for PenPartner.
UNINSTALLING THE SOFTWARE To remove PenPartner’s software driver from your system: For Windows: 1. 2. 3. 4. Click the Windows Start button. Then choose Settings and Control Panel. In the Control Panel window, double-click on the Add/Remove Programs icon. In the dialog box that appears, choose the WACOM Tablet option. Click on the Add/Remove... button and follow the prompts to remove the tablet software driver. For Macintosh: 1.
PRODUCT SPECIFICATIONS PENPARTNER TABLET (MODEL CT-0405-U) Active area (W x D) Physical size (W x D x H) Cable length Weight Power requirements Power consumption Resolution Accuracy (overall with pen) Pressure levels Reading height Report rate Communication interface Connector Operating temperature Storage temperature Operating relative humidity Storage relative humidity Compliance 128.0 x 96.0 mm (5.04 x 3.78 in) 196.0 x 181.0 x 7.0 mm (7.72 x 7.13 x 0.28 in) 2.0 m (6.6 ft) 430 g (0.
ULTRAPEN (MODEL UP-703E) Side switch color Eraser color Pen tip travel Eraser tip travel Physical size (L x D) Weight Tip refill type Light green Light green 0.1 mm (0.004 in) or less 2.0 mm (0.079 in) 140.5 x 11.4 mm (5.53 x 0.45 in) 11.2 g (0.395 oz) Polyacetal (Part No.
LICENSE AND WARRANTIES (Worldwide, except for Europe, Africa and Middle East) SOFTWARE LICENSE This legal document is an agreement between you, the end-user, and WACOM Technology Corporation (WACOM). 1. Grant of License. The enclosed product includes computer programs embedded in firmware and accompanying diskette or CD-ROM (the “Software”).
LIMITED WARRANTY WACOM warrants the product, except for the Software, to be free from defects in materials and workmanship under normal use and service as long as the product remains in production and in possession of the original owner, but not less than one (1) year, as long as you own the product as evidenced by a copy of the receipt and a registration card that has been returned to WACOM within 30 days of purchase. The Software is licensed “as is.
EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE, THERE ARE NO OTHER WARRANTIES MADE BY WACOM ON THIS PRODUCT. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY WACOM, ITS DEALERS, DISTRIBUTORS, AGENTS, OR EMPLOYEES SHALL CREATE A WARRANTY OR IN ANY WAY INCREASE THE SCOPE OF THIS WARRANTY, AND YOU MAY NOT RELY ON ANY SUCH INFORMATION OR ADVICE. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, WHICH VARY FROM STATE TO STATE.
WARRANTY ON SALES OUTSIDE OF U.S. AND CANADA For products purchased or used outside of the United States and Canada, the warranty is one (1) year from the date of purchase, and upon discovery of a defect in the product, except in the Software, within the Warranty Period you should notify your local dealer or distributor. In all other respects the terms of the warranty as set forth above apply to such sales.
LICENSE AND WARRANTIES (EUROPE) (Europe, Africa and Middle East) SOFTWARE LICENSE This legal document is an agreement between you, the end-user, and WACOM Europe GmbH (“WACOM”). 1. Grant of License. The enclosed product includes a computer program embedded in firmware and accompanying diskette or CD-ROM (the “Software”). The Software is licensed to you for use only upon the terms of this license, and WACOM reserves any rights not expressly granted to you.
LIMITED WARRANTY AND LIABILITY WACOM warrants to you as the original end-user that the product hardware is free from defects in materials and workmanship under normal use and service for a period of TWO (2) YEARS after the date of purchase, provided that they are unused at the time of such purchase. WACOM further warrants to you the accompanying diskettes against defects in materials and workmanship for a period of SIX (6) MONTHS) after the date of purchase. The Software is licensed and distributed “AS IS”.
EXCEPT FOR THE LIMITED WARRANTY DESCRIBED ABOVE THERE ARE NO OTHER WARRANTIES OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE MADE BY WACOM ON THIS PRODUCT. NO ORAL OR WRITTEN INFORMATION OR ADVICE GIVEN BY WACOM’S DEALERS, DISTRIBUTORS, AGENTS OR EMPLOYEES MAY ALTER OR INCREASE THE SCOPE OF THIS WARRANTY IN ANY WAY.
PARTS AND ACCESSORIES To order additional pens and other accessories, contact your WACOM dealer. TABLETS PenPartner (CT-0405-U) This is an entry-level tablet. Used as a mouse alternative or drawing tool, it enables you to more naturally point, click, draw, edit photos, and personalize projects. PENS UltraPen (UP-703E) This pressure-sensitive pen is an all-purpose tool to use for drawing, erasing, and typical mouse operations.
GLOSSARY Absolute positioning. A method for positioning the screen cursor. Wherever you place the pen on the tablet, the cursor will jump to the same corresponding point on the screen. This is normal pen behavior. See also relative positioning. Active area. The drawing area of the tablet where the pen is detected. Context aware. A WACOM feature that provides eraser support for some non-eraser aware applications.
Nib. The UltraPen’s replaceable tip. Non-eraser aware application. An application that does not have built-in support for the UltraPen’s eraser. See also eraser-aware application. Pixel. The smallest unit of measurement on your monitor screen. To double-click with the UltraPen, you must tap the tablet twice in the same place (same screen pixel). Pressure-sensitive application. Any application that supports input pressure.
Screen cursor. The cursor on the monitor screen. Screen cursors have different shapes, such as an arrow or a box, depending on the type of application you are running. Wintab. An interface standard used by Windows applications for receiving tablet information. PenPartner supports all Wintab-compatible applications under Windows. USB. Universal Serial Bus. A hardware interface standard for connecting computer peripheral devices.
INDEX About the manual Absolute positioning defined how to set when using pen Accessories and parts Active area, defined Appearance and features Application-specific problems, troubleshooting Box contents PenPartner Caring for pen and tablet Checklist, pre-contact Cleaning, how to Clicking how to making easier Conflicts, resolving for Macintosh Context aware, defined Control panel opening window Cursor controlling with pen defined Contents Index Customizing PenPartner Default settings, returning to DOS re
Information, product Installation Macintosh Windows Interference, radio and television Learning to use PenPartner License and Warranties (Europe, Africa and Middle East) License and Warranties Macintosh installation Macintosh troubleshooting Macintosh-specific problems, troubleshooting Manual, about Modifier keys, how to simulate Mouse buttons, how to simulate Movement mouse-like pen-like Nib defined replacing Non-eraser aware application, defined Parts and accessories Pen adjust for double-clicking adjusti
Pressure-sensitive application, defined Product information Proximity defined with the pen Radio and television interference Registration, mailing Relative positioning defined how to set Replacement parts ordering Screen cursor defined movement choosing pen or mouse like Side switch pen proximity required setting to simulate keyboard modifier keys to simulate mouse buttons Software driver, downloading the latest Specifications pen tablet Contents Index Tablet caring for cleaning specifications storing Tap
Tracing, maximum thickness allowed Troubleshooting application-specific problems general problems Macintosh Macintosh-specific problems Windows Windows-specific problems UltraPen, described Uninstalling software USB, defined Using PenPartner WACOM International Offices Warranties and License (Europe, Africa and Middle East) Warranties and License Web page, linking to Windows installation Windows troubleshooting Windows, customizing the pen in Windows-specific problems, troubleshooting WINTab, defined Conte
WACOM INTERNATIONAL OFFICES WACOM Technology Corporation WACOM Europe GmbH 1311 S.E. Cardinal Court Vancouver, WA 98683 U.S.A. Telephone General: ++1-360-896-9833 Fax: ++1-360-896-9724 Hellersbergstrasse 4 D-41460 Neuss Germany Telephone General: ++49-(0)2131-12390 Fax: ++49-(0)2131-101760 WACOM Co., Ltd.
